ASA Electronics WAOM562 Bedienungsanleitung

WAOM562

Pairing Process

If your monitor is not receiving a signal from the camera;

the two may not be paired correctly.

1. Camera and monitor must be connected to 12 Volt DC

power supply.

2. Remove “ pair” button cover from the side of the camera

(using a coin or fat head screwdriver).

3. Press and hold the “ pair” button on the back of

the monitor for 3 seconds and release.

(Monitor will display “ Please press TX pairing button” )

4. Press and hold the “ pair” button on the side of the

camera for 3 seconds and release (you have 60 seconds

to press this button.)

If done correctly, monitor will display “ Pairing successful” .

If pairing is not successful, the monitor will display “ Pairing

failed” . If you receive this message, repeat steps 2 - 4.

Installing The Monitor

1. Plug power cable into the back of the monitor. (fig. 1)

2. Attach the suction cup bracket to the rear of

the monitor with the supplied screws..

3. Locate flat section of glass on your windshield

1. POWER: Press to turn the WAOM562 on.

2. SELECT: Press to toggle the active display image

Between AV1 and AV

3. BRIGHTNESS - /+ :

Press BRIGHTNESS “–“ to darken the picture.

Press BRIGHTNESS “ +” to brighten the picture.

4. VOLUME ? /? :

Press VOLUME ? to decrease the volume.

Press VOLUME ? to increase the volume.

WAOM562

Pairing Process

If your monitor is not receiving a signal from the camera;

the two may not be paired correctly.

1. Camera and monitor must be connected to 12 Volt DC

power supply.

2. Remove “ pair” button cover from the side of the camera

(using a coin or fat head screwdriver).

3. Press and hold the “ pair” button on the back of

the monitor for 3 seconds and release.

(Monitor will display “ Please press TX pairing button” )

4. Press and hold the “ pair” button on the side of the

camera for 3 seconds and release (you have 60 seconds

to press this button.)

If done correctly, monitor will display “ Pairing successful” .

If pairing is not successful, the monitor will display “ Pairing

failed” . If you receive this message, repeat steps 2 - 4.

Installing The Monitor

1. Plug power cable into the back of the monitor. (fig. 1)

2. Attach the suction cup bracket to the rear of

the monitor with the supplied screws..

3. Locate flat section of glass on your windshield

1. POWER: Press to turn the WAOM562 on.

2. SELECT: Press to toggle the active display image

Between AV1 and AV

3. BRIGHTNESS - /+ :

Press BRIGHTNESS “–“ to darken the picture.

Press BRIGHTNESS “ +” to brighten the picture.

4. VOLUME ? /? :

Press VOLUME ? to decrease the volume.

Press VOLUME ? to increase the volume.

(that does not block your vision) and Apply

suction cup. Snap the lever into the locked

position.

4. Connect the power cord to a 12 Volt DC outlet.

5. Align the antenna to its upright position,

parallel to the monitor

Operation

1. Press the power button on the monitor and turn on

your vehicle’ s parking lights.

2. The monitor will display the Voyager logo for

8 seconds and then the camera image should

appear.

3. In the top right corner of the monitor, you will see

the signal strength meter.

4. Adjust the suction cup bracket to provide the best

viewing angle.

Notice :

The changes or modifications not expressly approved

by the party responsible for compliance could void the

user’ s authority to operate the equipment.

Important note:

To comply with the FCC RF exposure compliance

requirements, no change to the antenna or the device

is permitted. Any change to the antenna or the device

could result in the device exceeding the RF exposure

requirements and void user’ s authority to operate the

device.

   



    

 

 ! " # 

  $ "

 %"  

" #   &'  #

  "   $

("  ) 

*   

  + 

)     

"%  "+ 

)     

"% "   

"% ")  

  "

" 

  





  "%+

(that does not block your vision) and Apply

suction cup. Snap the lever into the locked

position.

4. Connect the power cord to a 12 Volt DC outlet.

5. Align the antenna to its upright position,

parallel to the monitor

Operation

1. Press the power button on the monitor and turn on

your vehicle’ s parking lights.

2. The monitor will display the Voyager logo for

8 seconds and then the camera image should

appear.

3. In the top right corner of the monitor, you will see

the signal strength meter.

4. Adjust the suction cup bracket to provide the best

viewing angle.

Notice :

The changes or modifications not expressly approved

by the party responsible for compliance could void the

user’ s authority to operate the equipment.

Important note:

To comply with the FCC RF exposure compliance

requirements, no change to the antenna or the device

is permitted. Any change to the antenna or the device

could result in the device exceeding the RF exposure

requirements and void user’ s authority to operate the

device.

   



    

 

 ! " # 

  $ "

 %"  

" #   &'  #

  "   $

("  ) 

*   

  + 

)     

"%  "+ 

)     

"% "   

"% ")  

  "

" 

  





  "%+

Andere Handbücher für WAOM562

Inhaltsverzeichnis

Andere ASA Electronics Monitor Handbücher

ASA Electronics

ASA Electronics WAOM562 Bedienungsanleitung

ASA Electronics

ASA Electronics Voyager AOM-7694 Bedienungsanleitung

ASA Electronics

ASA Electronics VOYAGER VOM-783T Bedienungsanleitung

ASA Electronics

ASA Electronics AOM713WP Bedienungsanleitung

ASA Electronics

ASA Electronics Voyager AOM701 Bedienungsanleitung

ASA Electronics

ASA Electronics Voyager VOM719WP Bedienungsanleitung

ASA Electronics

ASA Electronics Voyager AOM-7694 Bedienungsanleitung

ASA Electronics

ASA Electronics Voyager AOM681 Bedienungsanleitung

ASA Electronics

ASA Electronics AOM561 Bedienungsanleitung

ASA Electronics

ASA Electronics JE1029BMK Bedienungsanleitung

ASA Electronics

ASA Electronics FlexVision LCM1511WTV Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung