Asante IntraCore GBIC 1000LX Handbuch

Dieses Handbuch passt für folgende Modelle

3

Inhaltsverzeichnis

Andere Asante Schalten Handbücher

Asante

Asante FriendlyNET FM2008 Bedienungsanleitung

Asante

Asante Universal Serial Bus Hub USB Hub-4 Bedienungsanleitung

Asante

Asante FriendlyNet FH208B Bedienungsanleitung

Asante

Asante FriendlyNET Wireless USB Adapter Bedienungsanleitung

Asante

Asante IntraCore IC3624PWR Bedienungsanleitung

Asante

Asante IntraCore 3624PWR Handbuch

Asante

Asante IntraSwitch 6200 Series Handbuch

Asante

Asante IntraCore 35160 Series Bedienungsanleitung

Asante

Asante FriendlyNet FH208P Bedienungsanleitung

Asante

Asante FriendlyNET GX4-224 Bedienungsanleitung

Asante

Asante IntraCore 3524 Series Bedienungsanleitung

Asante

Asante IntraCore IC35160-G Bedienungsanleitung

Asante

Asante FriendlyNET 7000 Series Bedienungsanleitung

Asante

Asante FriendlyNET GXS-424W Bedienungsanleitung

Asante

Asante IntraCore 3624PWR Bedienungsanleitung

Asante

Asante GX5 Bedienungsanleitung

Asante

Asante IntraCore 35516 Series Bedienungsanleitung

Asante

Asante IntraCore IC36240 Series Bedienungsanleitung

Asante

Asante IntraCore IC39240 Bedienungsanleitung

Asante

Asante IntraSwitch 5212 Bedienungsanleitung

Asante

Asante IntraSwitch 5324 Bedienungsanleitung

Asante

Asante 3500 Bedienungsanleitung

Asante

Asante FriendlyNET 4024P Bedienungsanleitung

Asante

Asante IntraSwitch 5212 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch

06-00561-00 Rev.A Asanté Technologies, Inc.

Read Me First !

Model 99-00549-01 1000BaseSX GBIC

Model 99-00550-01 1000BaseLX GBIC

This yellow sheet describes how to install, remove, and maintain Gigabit Interface Converters

(GBICs). For more details, please refer to Asanté IntraCore 9000 or IntraCore 8000 manual.

Caution Unnecessary removal/insertion of a GBIC could lead to premature failure of the GBIC. A

GBIC has a lifetime of 100 to 500 removals/insertions.

GBIC Installation

Caution: When removing or inserting a GBIC, recommend to wear an ESD wrist strap .

Note GBICs are hot-swappable.

To install a GBIC, perform these following steps:

Step 1 Remove the GBIC from its protective packaging.

Step 2 Verify that the GBIC is the correct type for your network by checking the part number. The

number indicates whether it is 1000BaseSX ( multi-mode) , 1000BaseLX ( single-mode).

Step 3 Grip the sides of the GBIC with your thumb and forefinger; insert the GBIC into the slot on

the front of the module.

Step 4 Slide the GBIC into the slot until you hear a click. The click indicates the GBIC is locked

into the slot.

Step 5 When you are ready to attach the fiber-optic cable, remove the plugs from the GBIC and

save for future use.

GBIC Removal

To remove a GBIC, perform these following steps:

Step 1 Disconnect the fiber-optic cable from the GBIC SC-type connector.

Step 2 Release the GBIC from the slot by simultaneously squeezing the plastic tabs (one on

each side of the GBIC).

Step 3 Slide the GBIC out of the slot.

Step 4 Install the plugs in the GBIC optical bores, and place the GBIC in protective packaging.

GBIC Care and Handling

Follow these GBIC care and handling guidelines:

GBICs are static-sensitive. To prevent ESD damage, follow your normal board and

component handling procedures.

GBICs are dust-sensitive. When the GBIC is stored or when a fiber-optic cable is not

plugged in, always keep plugs in the GBIC optical bores.

The most common source of contaminants in the optical bores is debris picked up on the

ferrules of the optical connectors. Use an alcohol swab or Kim-Wipe to clean the ferrules

of the optical connector.