ASENWARE AW-D302 Bedienungsanleitung
Version: V1.0 Apr 28th,2018
1
ASENWARE LTD
ADDRESS: 6 PROSPECT WAY, ROYAL OAK INDUSTRIAL ESTATE DAVENTRY,
NORTHAMPTONSHIRE, ENGLAND, NN118PL
WEBSITE: www.asenware.com EMAIL: [email protected]
Instruction Manual of AW-D302 Addressable Heat Detector
------ Please read this Manual carefully before installing and using the product. -----
II. Product features
✓It can realize electronic coding and rewrite the address via coder in situ.
✓Within a single-chip microcomputer, it can realize real-time data acquisition and processing,
realize a curve tracing for the field situation.
✓It has a temperature compensation function and a sensor fault detection function (fault reporting
to fire alarm control panel).
✓Non-polarity, two-bus connection that ensures convenient installation and maintenance.
✓Designed with an upper cover and a lower cover and installed on an independent base, it can be
installed, debugged and maintained conveniently.
✓Built-in remote indicator output terminal, drive remote indicator lit when fire alarm。
III. Technical parameters
1. Executive standard: EN54-5
2. Operating voltage: 24V (pulse modulation)
3. Product class: A2
4. Standby current: ＜0.3mA;
5. Alarm current: no remote indicator ＜1.5mA , has remote indicator ＜3.5mA
6. Work indication: The red indicator will blink in the monitoring status or remain lit in the alarm
status.
7. Weight: about 115g(with the base)
8. External dimensions: diameter: 100mm, height: 60mm (with the base)
I. Product overview
AW-D302 Addressable Heat Detector (Detector hereunder) is a mated
product of the AW-FP300 fire alarm control panel. It uses a two-bus work
mode. With an internal microprocessor, it supports electronic coding. The
detector realizes real-time acquisition of the in situ temperature data and
sends back the data to a fire alarm control panel. It can also receive and
execute the control commands given by a fire alarm control panel. When in a
routing inspection, the detector indicator will blink. When there is a fire in the
monitored area and the temperature has reached the alarm threshold, the fire
alarm control panel will confirm a fire alarm according to the received message
sent from the detector, and the detector indicator will light at the same time to
indicate a fire alarm.
The detector is suitable for such industrial and civil buildings that have a great
deal of heat when fire takes place, such as kitchens, boiler rooms, generator
rooms, drying workshops and smoking rooms and is not suitable for places
with a great deal of smoke but little heat.
Version: V1.0 Apr 28th,2018
2
ASENWARE LTD
ADDRESS: 6 PROSPECT WAY, ROYAL OAK INDUSTRIAL ESTATE DAVENTRY,
NORTHAMPTONSHIRE, ENGLAND, NN118PL
WEBSITE: www.asenware.com EMAIL: [email protected]
9. Wiring method: non-polarity two-bus system (L1, L2); the terminal 2 and 4 can connect with
the remote indicator.
10. Operating environment: Indoor, temperature: －10℃～+50℃; relative humidity: ≤95% (non-
condensing)
11. Coding mode: It can realize electronic coding via coder in situ. Address codes 1 to 324 are
available for selection.
12. Matched host machine: AW-FP300 fire alarm control panel.
IV. Appearance and dimensions (see Fig.1)
Fig.1(unit:mm)
V. Use and engineering application
1. Fig.2 is the schematic diagram of the matched mounting base.
Fig.2
Definitions of terminals(non-polarity two-wire system):
1 --Signal terminal (L1)
2 – Negative of remote indicator
3 --Signal terminal (L2)
4 – Positive of remote indicator
2. Wiring method: The detector is accessed through a compatible fire alarm control panel via a two-wire
bus. It uses non-polarity connection. The terminals L1 and L2 of the two-wire bus are connected with
the terminals 1 and 3 of the matched mounting base. Fig.3 is a schematic diagram of the connection
between multiple detectors with a fire alarm control panel.
Version: V1.0 Apr 28th,2018
3
ASENWARE LTD
ADDRESS: 6 PROSPECT WAY, ROYAL OAK INDUSTRIAL ESTATE DAVENTRY,
NORTHAMPTONSHIRE, ENGLAND, NN118PL
WEBSITE: www.asenware.com EMAIL: [email protected]
Fig.3
3. Remote Indicator connection: the negative and positive of remote indicator should respectively
connect on terminals 2 and 4,as shown in Fig.4.
Fig.4
4. Coding address: As shown in Fig.5, detector is accessed via the detector mounting base on the coder,
non-polarity connection is adopted for the terminals L1 and L2, set the coder with the coding function,
select the correct address number and press the RUN key to complete the address code setup. (Note:
See the User’s Manual of the coder for the detailed operation.)
Fig.5
Intelligent
two-bus
controller
L2
L1
Version: V1.0 Apr 28th,2018
4
ASENWARE LTD
ADDRESS: 6 PROSPECT WAY, ROYAL OAK INDUSTRIAL ESTATE DAVENTRY,
NORTHAMPTONSHIRE, ENGLAND, NN118PL
WEBSITE: www.asenware.com EMAIL: [email protected]
VI. Installation and debugging
Determine the location, mounting distance and numbers for mounting the detectors in the protection area
according to relevant provisions and regulations of the local codes.
A self-contained complete base is necessary during the installation of a detector. As shown in Fig.6, the
model, the external dimensions, the mounting hole diameter and the mounting hole spacing of the base
are DZ-912, 100mm×26.4mm (diameter×thickness), 4.5mm and 44.5mm～64.3mm respectively.
Fig.6(unit:mm)
Wiring requirement:
It is proper to use RVS twisted pairs with a section area of equal to or larger than 1.0mm2 for the signal
buses L1 and L2.
Specific installation and debugging methods:
1. Make sure the type of the detector matches the type of the host machine of the fire alarm control
panel;
2. Use two M4 screws to fix the matched mounting base on the designated position via the
mounting holes A and B shown in Fig.6 as instructed in the construction drawing and make sure
the matched mounting base has been firmly installed.
3. Use a coder to make the detector coded according to the detector address on the construction
drawing.
4. Disconnect the power supply of the fire alarm control panel and connect the detector correctly
according to the construction drawing.
5. The lower edge of the detector base raised position aligned with the groove position, and then
the detector into the base, the detector clockwise until it locks into place the detector.
6. After all the products are installed and checked, connect the power supply of the fire alarm control
panel and conduct automatic login.
7. when automatic login is success, the red indicator of the detector will blink once about every 12
seconds, which suggests that the detector has begun to operate normally.
8. Finally conduct an alarm test for the detector through some special tools or direct hot air gun
blowing. After the detector gives a fire alarm, the indicator will remain lit and the fire alarm control
panel will simultaneously give corresponding alarm prompt information. After the alarm test, reset
the fire alarm control panel and restore to the monitoring status.
Version: V1.0 Apr 28th,2018
5
ASENWARE LTD
ADDRESS: 6 PROSPECT WAY, ROYAL OAK INDUSTRIAL ESTATE DAVENTRY,
NORTHAMPTONSHIRE, ENGLAND, NN118PL
WEBSITE: www.asenware.com EMAIL: [email protected]
VII. Precautions
1. A detector can not share an address with other equipment in a single bus circuit, or else an
address conflict may occur.
2. Never dismount the protective cover delivered with the detector too early after the field
installation and before the use of the detector, or else the detector may be contaminated.
3. It is not permitted to use open flames (such as lighters) to firing thermistor during alarm tests, so
as to avoid damage to the detector. It is recommended to use a hot air gun and other heating
equipment in a simulation alarm test.
4. The protection area and quantity of the detectors should comply with relevant provisions and
regulations of the local codes
VIII. Maintenance
Warning: Before conducting maintenance for a detector, inform the related management
department that the monitoring will be stopped temporarily when the system maintenance.
Meanwhile, disable the logic control function of the area or system to be maintained to avoid
unnecessary alarm linkage. After the test, inform the management department to restore the
normal functions of the system.
1. According to the requirements of local codes, each quarter, some special testing instruments should
be used to test the detector’s operation and confirm the indication state of its indicators by batch and
stage; for a detector that has been installed and used, It is recommended to have it maintained once
every two years.
2. If a detector fails due to a material defect or a manufacturing process defect under normal conditions
of use in one year following the date of its delivery, we shall repair or replace it for free. However, the
faults of the detector due to artificial damage, improper use, or authorized adjustment, reconstruction
or disassembly are not covered in the guarantee and we shall assume no responsibilities for any the
consequence thereby caused.
3. We may provide paid repair service for products with any faults beyond the guarantee range. If you
have such products that need repair, please contact us. When sending such a product to us for repair,
you are expected to provide some important information about the product, such as the phenomenon
and possible cause of the product fault, so that we can find out the cause of the fault in the shortest
time and so the information may be used as a reference in our future product development and
improvement.
IX. Fault analysis and troubleshooting
Fault
Possible cause
Troubleshooting method
Remarks
The detector can’t be
coded.
The internal circuit is damaged.
Send the detector back to the factory for
repair.
The detector can’t be
logged into normally.
The detector has no address or has
a coincident code.
Recode the detector.
The detector reports a
fault after login.
The contact with the base is poor
Inspect and reinstall the base.
The internal circuit is damaged.
Send the detector back to the factory for
repair.
The detector reports a
fire alarm after login.
The internal circuit has failed.
Send the detector back to the factory for
repair.
The detector can’t
send out fire alarm
signal during an alarm
test.
The internal circuit is damaged.
Send the detector back to the factory for
repair.
Inhaltsverzeichnis
Andere ASENWARE Sicherheitssensor Handbücher
