Ashford DOUBLE TREADLE KIT Bedienungsanleitung

INSTRUCTIONS

DOUBLE TREADLE KIT

ASHFORD TRADITIONAL SINGLE OR DOUBLE

Tools Required: Hammer, slot screwdriver, philips (pozi) screwdriver, candlewax, Ashford Spinning Wheel Oil.

Finishing the Wood: We recommend the wood surfaces be sealed before assembly. This protects the kiln dried wood from

climatic changes and enhances its beauty. Use either the Ashford Wax Finish or the same ﬁnish as

the rest of your wheel.

Assembly Sequence: Please read these instructions right through before commencing.

Parts:

1. Remove from the crank either:

a) the split pin with a pair of pliers

b) the O-ring with a pin or needle

c) the E-clip with a small screwdriver

Take off old con rod from the crank.

2. Remove the hub pin. - Use the nail provided and a hammer. Note: on

earlier models the hub pin is in the middle of the hub. Avoid damaging

the spokes. Place a ﬂat steel object such as pliers or a spanner over the

nail and hammer it.

3. Remove the crank from the wheel.

b) On old spinning wheels use a slot screwdriver to prise the bent

1/8” diameter hub pin out.

4. Remove the wheel from the frame. Clean the bearings and wheel.

Remove any ﬁbres that may have collected around the crank.

5. Replace the wheel into position. Note: the hub pin is on the same side as

the con rods.

6. Push the double treadle crank (with the inner con rod attached)

through the wheel supports and into the hub. There are two holes in the

crank. One will ﬁt your wheel.

7. Place the nail down the hub pin slot and into the hole in the crank.

Remove the nail and replace it with the hub pin.

Ashford Handicrafts Ltd.

Factory and Showroom: 415 West Street,

PO Box 474, Ashburton, New Zealand

Telephone 64 3 308 9087

Facsimile 64 3 308 8664

Email: [email protected].nz

Internet: www.ashford.co.nz

Ashford Guarantee

Thank you for purchasing this Ashford product. In the

unlikely event there is any fault in manufacture we will

replace the item. To validate our guarantee please visit

our website or write to us.

Please also join our Ashford Club for the Wheel Magazine,

competitions and more at www.ashfordclub.co.nz

8. Loosen the bolts or screws holding the single leg to

the frame. Use either the allen key provided or a slot

screwdriver. Remove the old treadle rail.

9. Rub candle wax onto the steel pins projecting from the

new treadle rail.

10. Place the Double Treadle Assembly into position between

the two legs.

11. Push the single leg against the treadle rail. Retighten the

bolts or screws.

Special Features:

Easy to start - no need to use your hands. Just start treadling. Enjoy comfortable

heel and toe action.

New treadling action - the cranks are off set 10 degrees so you can start the wheel in either

direction.

Good posture - when you use both feet to treadle your body is naturally in balance.

Less muscle fatigue - the Double Treadle Kit reduces ankle, leg and hip fatigue.

Update kit - your spinning wheel has now been updated with the new crank and

con rod joints. No more clunky treadling.

12. Locate the nylon washer onto the end of the crank.

13. Position the outside con rod onto the end of the crank.

The nylon bearing towards the outside.

14. Push the E clip into the groove in the end of the crank

with a screwdriver.

15. Attach the con rod joints to the treadle boards with

screws. Leave about 19 mm (¾in) gap between the con

rod and treadle board.

16. If the new treadle rail touches the back leg lie the wheel

down, loosen the screws attaching the treadle rail to the

treadle board. Move it slightly away and retighten the

screws.

17. Lubricate all moving parts with Ashford Spinning Wheel

Oil. Now you can enjoy spinning on your new Ashford

Double Treadle Kit.

DTKTD14022012V2

Inhaltsverzeichnis

Andere Ashford Webwerkzeuge & Zubehör Handbücher

Ashford

Ashford DOUBLE TREADLE KIT Bedienungsanleitung

Ashford

Ashford SPINNING WHEEL MAINTENANCE KIT Bedienungsanleitung

Ashford

Ashford SampleIt Loom Stand Bedienungsanleitung

Ashford

Ashford DRUM CARDER Fine Bedienungsanleitung

Ashford

Ashford RIGID HEDDLE FREEDOM ROLLER Bedienungsanleitung

Ashford

Ashford KNITTERS LOOM STAND Bedienungsanleitung

Ashford

Ashford SPINNING CHAIR Bedienungsanleitung

Ashford

Ashford RIGID HEDDLE LOOM STAND Bedienungsanleitung

Ashford

Ashford KNITTERS LOOM STAND VARIABLE WIDTH Bedienungsanleitung

Ashford

Ashford WEAVING STARTER KIT Bedienungsanleitung

Ashford

Ashford BALL WINDER Bedienungsanleitung

Ashford

Ashford RIGID HEDDLE TABLE STAND Bedienungsanleitung

Ashford

Ashford KNITTERS LOOM SECOND HEDDLE KIT Bedienungsanleitung

Ashford

Ashford PACKER BRUSH Bedienungsanleitung

Ashford

Ashford WOODEN UMBRELLA SWIFT Bedienungsanleitung

Ashford

Ashford EDC30 Bedienungsanleitung

Ashford

Ashford KIWI 2 SPINNING WHEEL Bedienungsanleitung

Ashford

Ashford WEAVING FRAME SMALL Bedienungsanleitung

Ashford

Ashford Drum Carder Bedienungsanleitung

Ashford

Ashford SKEINER 2 Bedienungsanleitung

Ashford

Ashford QUILL SPINDLE Bedienungsanleitung

Ashford

Ashford DOUBLE TREADLE KIT Bedienungsanleitung

Ashford

Ashford Lazy Kate Super Jumbo Bedienungsanleitung

Ashford

Ashford KNITTERS LOOM STAND Bedienungsanleitung

Beliebte Webwerkzeuge & Zubehör Handbücher anderer Marken

Beadalon

Beadalon 216S-100 Bedienungsanleitung

BEKA

BEKA Yarn Swift Bedienungsanleitung

Beadalon

Beadalon TOGGLE JIG Bedienungsanleitung

Toika

Toika Eeva ES Bedienungsanleitung

Weaver

Weaver Weaver Snap Davits Bedienungsanleitung

Beadalon

Beadalon Ring Weaver Tool Bedienungsanleitung

Xiamen Rizheng Industry

Xiamen Rizheng Industry Crochet Hook Kit Set Bedienungsanleitung

Read Pleaters

Read Pleaters 24-Row Regular Bedienungsanleitung

MOKIDA

MOKIDA ZM2642501SYL-000-000 Bedienungsanleitung

Artistic Wire

Artistic Wire Findings Forms 228S-661 Bedienungsanleitung