Ask HDEX0018M1 Bedienungsanleitung
User Manual
Mini HDMI Wireless Extender
Model No. HDEX0018M1
FEATURES OF THE INTERFACE:
Picture 1.0 Transmitter (TX)
Picture 1.1 Receiver (RX)
HDMI input port
USB 5V power jack
Power status light
IR out port
Built-in reset key
HDMI Signal light
Wireless status light
IR in port
Built-in reset key
HDMI Signal light
Wireless status light
HDMI output port
USB 5V power jack
Power status light
Connection and Operation:
1. CONNECTION DIAGRAM
1.1 Connect the HDMI input port of the HDMI wireless TX to the HDMI output port of the signal source by
HDMI cable.
1.2 Connect the HDMI output port of the HDMI wireless RX to the HDMI input port of the TV/Monitor by
HDMI cable.
1.3 Connect the IR Transmitter cable to the HDMI wireless TX and the IR Transmitter cable must face to
the control target device.
1.4 Connect IR Receiver cable to the HDMI wireless RX.
1.5 Connect 5V power supplies to the TX&RX, the POWER indicator will be lit at this moment.
1.6 The device will automatically connect after power on. The STATUS indicator of TX and RX will be lit
when the connection is successful. If the HDMI input or output signal is normal, the HDMI indicator
light will be lit also. The STATUS indicator flashes continuously during normal transmission.
1.7 Note: the antenna is located on the side near the IR interface, Please point these two faces towards
each other when placing them.
HDMI-Mini HDMI cable
TX
RX
USB
HDMI-Mini HDMI cable
IR Transmitter cable
IR Receiver cable
USB
This side faces RX
Source remote control
HDTV Monitor/Projector
DVD/PS3/STB/PC
This side faces TX
2. Restore factory settings and switch wireless band:
The reset key is hidden in the RESET hole. It is able to work under power on status. To use one
long and narrow insulated stick (like toothpick) to insert the hole end to press the button as below:
2.1 Restore Factory Setting: To press the button for lasting three seconds, then the HDMI Status
Led Light will flash for three times and restart, it shows that Restore Factory Set is successful.
Note: You must to restore factory set at both transmitter and receiver.
2.2 Switch Wireless Band: Press the button to cyclic switch the 2.4G/5G (only for TX). The default
frequency is 5G.
3. Web settings:
To prevent the interference caused by the same frequency device, the Wireless HDMI Extender
support to set up the working frequency, transmit channel and SSID by the WEB. For safety, the user
should change the SSDI and the password at the first log in. Please follow the below steps:
3.1 Connect 5V power supplies to the TX&RX, and let them be connected.
3.2 Turn on the WLAN of the mobile phone / PC，search and connect SSID：Mini_HDMI_Wireless,
Enter the default password: 00000000.
3.3 Modify the IP address type of the mobile phone / PC to Auto. When you select static type, you
must be set the IP in 192.168.1. xxx address segment range, e.g. 192.168.1.100.
3.4 Open the browser and scan the QR code or enter “192.168.1.10”
in the address bar to enter the configuration page..As shown below:
3.5 Enter the default login password: admin,click “Login” open the Settings Interface. If you want
to modify the login password, please click on the " Modify ", after modified click "save" to save
and exit. Restore factory settings when click "reset".
3.6 If you have an error in setting or forgot the password, you can restore factory setting.
4. Other notes:
4.1 When transmitting over long distances, it may be necessary to adjust the position or Angle of
the product to obtain stable signals.
4.2 The operating frequency of the product is the same as that of WIFI, Users are advised to
adjust the wireless frequency band or channel to avoid the same frequency interference.
4.3 Concrete walls, Brick, Wallpaper, Metal, Bulletproof glass will shorten the signal cover range
or cause big signal loss. Please try not to allow wireless signals to pass through these
obstacles.
4.4 If you need to get around certain obstacles or get a longer transmission distance, you can add
a wireless repeater in the middle of the transmission path. Please consult the supplier for
details.
SPECIFICATIONS:
Model No.
HDEX0018M1
Model name
Mini HDMI Wireless Extender
HDMI resolution
480P/720P/1080P@50Hz/60Hz
HDMI Audio format
LPCM2.0/48KHz/16Bit
HDMI Max bandwidth
225MHz
HDMI Max baud rate
6.75Gbps
Output cable length
1080P/AWG 26 ≤12m
Antenna type
Built-in 3dBi gain antenna
Wireless standard
IEEE 802.11a/n/ac
Wireless Band
2.4GHz / 5GHz ISM Band
Max Data rates
up to 150Mbps
Transmit Output Power
14±2dBm（IPEX）
Transmission distance
up to 60m (in open space)
IR Carrier frequency
20-60KHz
Power adapter specification
AC 100~240V / USB 5V/1A
Max working current
TX≤750mA / RX≤550mA
Working temperature range
-5 ~ +40℃
Working humidity range
5 to 85%RH（No Condensation）
Storage temperature
-15 to 55℃
Storage humidity
5 ~95%RH(No Condensation)
Size
85*62.5*15 (mm)
Weight
TX 57g/RX 56g
Accessories
Manual x1, Power Adaptor x2, USB cablex2, HDMI-Mini HDMI
cable x2, IR Transmitter cable x1, IR Receiver cable x1
Inhaltsverzeichnis
Andere Ask Extender Handbücher
