Asko T411HSW Bedienungsanleitung

INSTALLATION INSTRUCTIONS

TD85

Carefully read the instructions for use before using the dryer.

Heat pump Tumble Dryer

DOMESTIC

WARNING - Risk of ﬁre.

Install the clothes dryer according to

the manufacturer's instructions and

local codes.

To reduce the risk of of severe

injury or death, follow all installation

instructions.

SAVE THESE INSTRUCTIONS FOR

FUTURE REFERENCE.

After installation, wait for 24 hours without

moving the appliance before using it for the ﬁrst time.

If the dryer has to be laid down on one of the sides

during transport or servicing, place it with its left

side, viewing from the appliance front, downwards.

90° 90°

WARNING

Clothes dryer installation must be

performed by a qualiﬁed installer.

DRYER PLACEMENT

The dryer can be either freestanding or installed

onto a washing machine.

The dryer emits heat. Therefore, do not place it in

a very small room, as the drying process may be

longer due to limited amount of available air.

Do not place the dryer in a room where

temperature can drop below 0 °C (32 °F), as the

machine may not operate correctly at such low

temperatures or may freeze, which can result in

damage to the machine.

Install the dryer in a room with adequate ventilation

and a temperature between 10 °C (50 °F) and 25 °C

(77 °F).

Do not place the dryer behind lockable or sliding

doors, or doors with a hinge on the opposite side of

the dryer door hinge. Install the dryer in such way

that the door can always be freely opened.

Never block the air exhaust (evacuation opening).

At least two persons are required to install the

tumble dryer on top of a washing machine.

Do not place the dryer on a carpet with long ﬁbres

as this may impede air circulation.

INSTALLATION

Dear Customer,

Read these instructions carefully and completely before you install the machine. The installation should

be carried out by a qualiﬁed person who is familiar with all local codes and ordinances for electrical and

plumbing connections. See also the general Safety Instructions in the Use & Care Guide.

Cosmetic damage must be reported to the ASKO dealer within ﬁve days from the date of purchase. As soon

as you unpack the machine, thoroughly check it for cosmetic damage.

The appliance may not be in contact with a wall

or adjacent furniture. For optimum dryer operation,

observe the clearance from the wall as shown in the

ﬁgure.

Freestanding appliance

The dryer may be placed adjacent to a washing

machine.

If the friction between the dryer feet and the ﬂoor is

not suﬃcient, the dryer may move during operation.

To prevent sliding, use a non-slide mat or install the

supplied vacuum feet onto both front feet.

Place the dryer so that it is stable. Use a spirit level

to level the dryer horizontally and vertically by

rotating the adjustable feet using a No. 22 (0.87")

spanner (max. 15 mm (0.59")). Then, ﬁrmly tighten

the jam nuts (counter nuts) by rotating them towards

the appliance bottom using a No. 17 (0.67") spanner

Clearance around the dryer for optimum

operation

50 mm (2")

100 mm (4")

The appliance may not be in contact with a wall

or adjacent furniture. For optimum dryer operation,

observe the clearance from the wall as shown in the

ﬁgure.

Opening the dryer door (top view)

1189 mm (47")

480 mm (19")

176°

Stacking on top of a washing machine

To stack the dryer on top of a washing machine, use

the extra vacuum feet and the tipping guard (A+B),

supplied in the cardboard box in the dryer drum.

Tipping guard part B is designed to ﬁt on ASKO

washing machines and it may be hard or impossible

to mount on appliances of other brands. If the

washing machine and dryer are not of matching

dimensions or if you have installed a hidden helper

between the two appliances, then binding plates are

available as optional accessories at the service unit

(available only for HH (accessory Hidden Helpers)

and TD75 stacked on top of WM80 or WM85; not

intended for any other combinations).

All ASKO washing machines can bear the weight of

the dryer.

Washing machine on which you wish to install

the dryer must be able to bear the weight of the dryer

(see washing machine’s rating plate or technical

information).

How to stack a dryer onto the washing machine (ASKO):

There is a cardboard box in the dryer drum, containing the vacuum feet and the tipping guard.

A B

1The tipping guard consists of two metal parts (A +

B).

Use two screws to attach the A part to the back of the

dryer.

2Undo the screw on the back side of the washing

machine.

3Use the screw to attach the tipping guard (B part)

to the back of the washing machine.

4Level the washing machine so that it is stable.

1. Level the washing machine by rotating the

adjustable feet using a No. 32 (1.26") spanner.

The feet allow levelling by +/- 1 cm (0.39").

2. After adjusting the height of the feet, ﬁrmly

tighten the jam nuts using a spanner No 17

(0.67"), by turning them towards the bottom of

the washing machine .

3. Tighten the jam nuts.

5 mm

5Set the dryer feet:

1. Tighten the front two feet all the way in.

2. Undo the back feet by 3.5 turns or 5 mm (0.2");

then, fasten the jam nuts towards the bottom of

the appliance .

6Place the dryer onto the washing machine:

1. Lift the front part of the dryer by 5 cm (2") to

10 cm (4").

2. Attach the vacuum feet onto the front feet of the

dryer.

3. Push the dryer into the tipping guard (so that

the B part is inserted into the A part) and

release it (See ﬁgure on previous page).

Make sure the tipping guard is "locked"!

CHANGING THE DOOR OPENING DIRECTION

To change the direction of door opening, proceed as follows.

1Open the door fully.

2Undo the screws and remove the door.

3Use the screwdriver to remove the door lock cover

and undo the screw on the door lock.

4Push the door lock upwards and remove it. Move

it to the other side and push it downwards.

5Fasten the screw on the door lock. Replace the

door lock cover.

6Undo the door hinge assembly (left) and the door

latch assembly (right), switch their positions, and

replace the screws (door hinge assembly to the right-

hand side, door latch assembly to the left-hand side).

Use the screwdriver to remove the plastic part

more easily.

7Undo the door ring and remove it temporarily.

8Rotate the door glass cover by 90° so that the sign

indicating the opening of the door is on the other

side.

9Rotate the door ring by 180°, install it onto the

door, and fasten it with screws.

10 Replace the door on the door hinge and fasten

the screws.

BUILT-IN

30-1/3"

770 mm

ASKO dryers can be installed beneath a cabinet

or worktop with a minimum height of 34" (864

mm). There must be a gap of about 1/2" (12 mm)

all around the machine and a minimum gap of 1"

(25 mm) between the rear edge of the machine top

panel and the back wall. The opening width must be

at least 24-1/2" (622 mm).

The condensing models work best when they have

good air circulation.

Install the dryer so the condensed water will

continuously ﬂow into a drain or sink. You will need

a drain outlet behind the unit. The maximum drain

height is 40" (1016 mm).

The height adjustment for the dryer is 33- 1/2" to

34-1/2" (850 mm to 876 mm). Do not raise it higher

than 34-1/2" (876 mm).

It is very important to avoid a buildup of heat.

The warm air that is expelled from the rear of the

dryer must be able to dissipate.

Warm air that cannot dissipate could cause a

fault.

A buildup of heat could be avoided by:

• Creating a gap for the dryer in the kitchen

furniture plinth facing.

• Creating ventilation gaps in the kitchen unit.

When build under, drying times may be longer.

The dryer should not be installed next to a

refrigeration appliance. The warm air expelled from

the rear of the dryer would increase the temperature

around the refrigeration appliance heat exchanger

causing the compressor to run continuously. If it is

not possible to install the dryer anywhere else, then

the refrigeration appliance must be sealed oﬀfrom

the dryer.

Closet Install- Ventilation Requirements

ASKO's front panel controls make it possible to

install the washers and dryers in a closet. Make sure

there is clearance between units and cabinet or wall

and a 1" (25 mm) minimum clearance between the

rear edge of the machine top panel and the cabinet

or wall. To ensure proper ventilation, we recommend

louvered doors, particularly for condenser dryers.

Otherwise there must be ventilation openings in

the door. See illustration for minimum ventilation

openings below (gray boxes):

Ensure the dryer door can be opened without

hindrance after installation.

The cool air intake panel at the front of the dryer

must not be blocked or covered. Doing so could

cause an error.

DRAINING THE CONDENSATE

The moisture from the laundry is extracted in the

condenser unit and accumulated in the condensate

tank. Condensate tank has to be emptied regularly

(see chapter "CLEANING AND MAINTENANCE" in

the instructions for use.)).

Interruption of the drying cycle due to full

condensate tank can be avoided by running the

condensate discharge hose found at the back of the

appliance directly into a drain.

Remove the small short hose from the attachment

(A).

max 1000 mm

max 39.4"

max 300 mm

max 11.8"

Connect the supplied drain hose to the same

attachment (A). The supplied drain hose has a

length of 78 3/4" (2000 mm).

Run the condensate drain hose into a drain. Tie the

hose onto a tap (B) so that it cannot slip during use.

The drain hose can also be fed into the washbasin

siphon (C) or directly into the ﬂoor drain (D).

Then, the water is pumped directly into a washbasin,

a siphon, or a ﬂoor drain.

Do not pull the drain hose, and make sure it is

not under tension, clamped, or bent.

If you decide to run the condensate drain hose

into a drain, siphon, or washbasin, make sure the

hose is securely fastened. This will prevent any

water spillage which could result in unexpected

damage.

Always use hoses that are supplied with the

appliance.

If the dryer is connected to an air exhaust

system already used for another appliance, a non-

return valve must be installed. Return ﬂow into the

dryer could damage the appliance and the non-

return valve prevents such ﬂow.

TRANSPORT/WINTER STORAGE

The machine must be transported upright!

Leave the machine to stand upright for 24 hours after

transporting. If you need to move your machine or

store it over the winter in unheated premises, make

sure that you drain the condensed water container

beforehand.

ELECTRICAL INSTALLATION

The receptacle on the rear of the machine is

designed to accommodate ASKO washers ONLY

(rated 208–240 V.) To use this receptacle, you must

use the ready-fitted plug supplied with the washing

machine or an equivalent.

ASKO washers rated 208–240 V have two internal

fuses of 15 A each.

The machine should only be connected to a

grounded wall socket.

This appliance must be properly grounded. Refer

to the “Important Safety Instructions” for grounding

instructions.

The power supply cord must be grounded. If the

machine is to be used in a wet area, the supply must

be protected by a residual current device.

Connection to a permanently wired supply point must

be made only by a qualified electrician.

As supplied: Single-phase, 230 V, 60 Hz, 3000W

heater rating 30 A circuit required.

Do not connect the machine to the mains

electricity supply by an extension lead.

Remove cover to access teminal box.

(Requires- Torx screwdriver.)

Electrical Connections

Read the Electrical requirements and grounding

instructions before connecting the tumble dryer.

Electric models of the dryer are manufactured for

a 3-wire connection system. The dryer frame is

grounded by a link to the neutral conductor on the

dryer terminal block. If local codes do not permit

grounding through the neutral, the grounding link

from the terminal block must be removed and a

separate ground wire must be used.

Only a 4-conductor cord shall be used when the

appliance is installed in a location where grounding

through the neutral conductor is prohibited.

Grounding through the neutral conductor is

prohibited for new branch-circuit installations,

mobile homes, recreational vehicles, and areas

where local codes prohibit grounding through the

neutral conductors. The grounding link on the dryer

must be removed for all 4-wire installations.

These Electrical Connection instructions provide for

installing the dryer in the following situations:

3-wire connections where local codes permit

grounding through the neutral, 3-wire connections

with a separate grounding connector where local

codes do not permit grounding through the neutral,

and 4-wire connections.

Each of the above connections can be made

with an approved power supply cord or by direct

wiring. Each connection instruction identiﬁes

the appropriate Power Supply Cord and covers

requirements for direct wiring.

In Canada, the dryer is delivered ready-ﬁtted

with a four-prong plug intended for connection to a

single-phase supply.

Connecting a 3-wire Power Cord

Before starting this procedure, be sure the power

is turned off at the breaker/fuse box.

Spade terminals

with upturned

ends

Ring

terminals

Ground

(center)

3/4" UL-listed

strain relief

Ground

This blade connects to

this conductor.

3-Wire Cord

Power Supply Cord

You will need a 3-wire power supply cord with

three No. 10 copper wires and a matching 3-wire

receptacle of NEMA Type 10-30R, as illustrated

below:

To connect a 3-wire power cord to the dryer, follow

the steps below.

The numbers in the illustration correlate to the

step numbers.

Andere Handbücher für T411HSW

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Asko Trockner Handbücher

Asko

Asko TD60.C Bedienungsanleitung

Asko

Asko TD75.13 Series Bedienungsanleitung

Asko

Asko TDC111VACS Bedienungsanleitung

Asko

Asko DC7784HP Bedienungsanleitung

Asko

Asko TL751 XXLW Bedienungsanleitung

Asko

Asko TL751G XXL Bedienungsanleitung

Asko

Asko T608HX UK Series Bedienungsanleitung

Asko

Asko TDC33 Bedienungsanleitung

Asko

Asko Professional TDC145HPS Bedienungsanleitung

Asko

Asko T2082H Bedienungsanleitung

Asko

Asko PROFESSIONAL TDC145VS Bedienungsanleitung

Asko

Asko T611VU.W.U Bedienungsanleitung

Asko

Asko T208H.W.AU Bedienungsanleitung

Asko

Asko DC7784HP.S.UK Bedienungsanleitung

Asko

Asko TLS752 Bedienungsanleitung

Asko

Asko T743C Montageanleitung

Asko

Asko TL751 XXLW Bedienungsanleitung

Asko

Asko PROFESSIONAL TDC112HPS Bedienungsanleitung

Asko

Asko DC 7171 Bedienungsanleitung

Asko

Asko T756HP Bedienungsanleitung

Asko

Asko DC7784HP.W.AU Bedienungsanleitung

Asko

Asko TD30 Bedienungsanleitung

Asko

Asko T731 Bedienungsanleitung

Asko

Asko TD75.C27X Bedienungsanleitung

Beliebte Trockner Handbücher anderer Marken

Bosch

Bosch WTA79200GB Bedienungsanleitung

Amana

Amana W10233410A Bedienungsanleitung

Miele

Miele TWH 780 WP Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Bedienungsanleitung

Bosch

Bosch Logixx 10 WTB76556GB Technisches Datenblatt

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Bedienungsanleitung

Electrolux

Electrolux EW2H328R2 Bedienungsanleitung

Beko

Beko DS8433RX1M Bedienungsanleitung

Dawlance

Dawlance Spinner DS 6000 C Bedienungsanleitung

Electrolux

Electrolux TP5080TW Bedienungsanleitung

AEG

AEG TR838P4OB Bedienungsanleitung

Indesit

Indesit IDV 75 Bedienungsanleitung

Infiniton

Infiniton SD-DG85C Bedienungsanleitung

BOMANN

BOMANN WT 5019 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Bedienungsanleitung

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Bedienungsanleitung

Frigidaire

Frigidaire CAQE7077KW0 Betriebsanleitung

Bosch

Bosch WTX8HKM9SN Bedienungsanleitung