ASL INTERCOM LP01 Bedienungsanleitung

ASL Document Ref.: U-0641-3675.docx

Issue: 01 complete, approved - Date: 24/09/21

NETWORK-SWITCH-LP01

Configuration Guide

NETWORK-SWITCH-LP01 – Configuration Guide

Application Solutions (Safety and Security) Limited

Unit 17 Cliffe Industrial Estate

Lewes - East Sussex

BN8 6JL - UK

Tel: +44(0)1273 405411 Fax: +44(0)1273 405415

www.asl-control.co.uk

Information contained in this document is believed to be accurate, however no representation or warranty is given and Application

Solutions (Safety and Security) Limited assumes no liability with respect to the accuracy of such information.

U-0641-3675.docx – Issue: 01 complete, approved

Page 2 of 28

Document Change History

Issue Amendment Summary Date

1 First Release 24/09/21

Contents

1Introduction .............................................................................................................................................. 3

1.1 Port Capabilities ......................................................................................................................... 3

1.2 Required PC Tools and PC Configuration.................................................................................. 3

1.3 Systems Containing VIPEDIA-12-PRO and/or INTEGRA-PRO................................................. 3

2Wiring and Hardware Settings................................................................................................................ 4

2.1 Wiring.......................................................................................................................................... 4

2.1.1 Power .................................................................................................................................. 4

2.1.2 Ethernet .............................................................................................................................. 4

2.1.3 Fault Relay .......................................................................................................................... 4

2.2 Hardware Settings ...................................................................................................................... 5

2.2.1 Fault Reporting ................................................................................................................... 5

2.2.2 SFP Speed.......................................................................................................................... 6

3Configuration............................................................................................................................................ 7

3.1 Login ........................................................................................................................................... 7

3.2 IP Settings and Hostname.......................................................................................................... 8

3.3 ASL Secure Loop (RSTP) ........................................................................................................ 10

3.1 Systems Containing VIPEDIA-12-PRO and/or INTEGRA-PRO............................................... 13

3.1.1 QoS (Quality of Service) ................................................................................................... 13

3.1.2 IGMP Snooping................................................................................................................. 15

3.1.3 Dante Controller................................................................................................................ 19

3.2 Save / Load Configuration ........................................................................................................ 20

3.2.1 Save Configuration to Device ........................................................................................... 20

3.2.2 Save Configuration to PC ................................................................................................. 21

3.2.3 Load Configuration from PC ............................................................................................. 22

4APPENDIX – PC Requirements............................................................................................................. 23

5APPENDIX – Factory Reset................................................................................................................... 26

Please refer to ASL downloads page for latest revisions of all user documentation.

www.asl-control.co.uk/downloads

Note:

Audinate® is a registered trademark of Audinate Pty Ltd.

Dante™ is a trademark of Audinate Pty Ltd

NETWORK-SWITCH-LP01 – Configuration Guide

U-0641-3675.docx – Issue: 01 complete, approved

Page 3 of 28

1 Introduction

This Configuration Guide describes how to configure ASL NETWORK-SWITCH-LP01 for use in an ASL

PAVA system. It covers fault reporting, SFP speed, ASL Secure Loop (RSTP), and additional configuration

for systems that include VIPEDIA-12-PRO and/or INTEGRA-PRO units.

The instructions in this document are correct for network switch software V1.0.1.S0. Newer or older software

may provide different features or have different configuration options.

Features not covered in this Configuration Guide are covered in the NETWORK-SWITCH-LP01 User

Manual. For access, go to the ASL website at www.asl-control.co.uk or scan the QR code on page 2.

1.1 Port Capabilities

NETWORK-SWITCH-LP01 has the following port capabilities:

•8 x RJ45 copper 10/100 Mbps connection speed.

•2 x SFP 100/1000 Mbps connection speed.

1.2 Required PC Tools and PC Configuration

NETWORK-SWITCH-LP01 configuration requires:

1. A PC (Windows 10) with the network interface configured correctly to communicate with the network

switch.

For instructions, refer to section 4 APPENDIX – PC Requirements on page 23.

2. A web browser.

1.3 Systems Containing VIPEDIA-12-PRO and/or INTEGRA-PRO

The NETWORK-SWITCH-LP01 is compatible with systems containing VIPEDIA-12-PRO and/or INTEGRA-

PRO units where the overall network traffic is no greater than 30 Mbps. This includes all traffic from the ASL

system, non-ASL equipment, and Dante.

Use the following figures to estimate the overall network traffic:

1. Each Dante multicast flow is between 3 Mbps (containing 1 channel, the minimum) to 11 Mbps

(containing 8 channels, the maximum).

2. Each Dante unicast flow is approximately 6 Mbps (containing up to a maximum of 4 channels).

3. Each ASL audio stream (over PMC)1is approximately 1 Mbps.

To estimate the overall network traffic, add the expected number of Dante multicast and unicast flows to the

expected number of concurrent ASL audio streams.

Other network traffic has negligible impact on the overall network traffic.

1ASL audio sources are routed to remote units over IP using ASL's PMC format.



VIPEDIA-12-PRO and/or INTEGRA-PRO audio inputs configured as Dante are automatically

configured as multicast flows when using the “Export Dante Controller File” feature in the PAVA

System Configuration Tool.

If all twelve inputs are configured, the first eight inputs are in one Dante multicast flow (approx.

11 Mbps) and the next four are in a second Dante multicast flow (approx. 5 Mbps), giving 16 Mbps

traffic.

Note that an input routed over Dante to remote units is also routed over PMC.

NETWORK-SWITCH-LP01 – Configuration Guide

U-0641-3675.docx – Issue: 01 complete, approved

Page 4 of 28

2 Wiring and Hardware Settings

2.1 Wiring

2.1.1 Power

Refer to the NETWORK-SWITCH-LP01 User Manual for the voltage range and wiring instructions for the

primary and, if required, the secondary power supply.

2.1.2 Ethernet

All NETWORK-SWITCH-LP01 units have the same factory default IP address, 192.168.2.5. The default

netmask is 255.255.255.0.

2.1.3 Fault Relay

The NETWORK-SWITCH-LP01 fault relay should be connected to an onboard or BMB01 fault contact input

in the PAVA system, and the network switch configured to report power supply and Ethernet connection

faults.

For wiring instructions for the fault relay, refer to the NETWORK-SWITCH-LP01 User Manual and the

relevant ASL product documentation

For the network switch fault relay configuration, refer to section 2.2.1 Fault Reporting on page 5.

For PAVA system onboard or BMB01 fault contact input configuration, refer to the relevant ASL product

documentation.

For EN 54-16 compliance, a separate power supply must be connected as a secondary power

source.

Do not connect network switches together until the configuration in section 3 Configuration on

page 7 is complete for each unit.

This is to prevent configuration issues due to multiple network switches with the same IP address,

and to prevent data storm due to RSTP being disabled by default.

For EN 54-16 compliance, the fault relay must be connected and configured as described above.

The PAVA system fault contact input must be configured to active low.

NETWORK-SWITCH-LP01 – Configuration Guide

U-0641-3675.docx – Issue: 01 complete, approved

Page 5 of 28

2.2 Hardware Settings

2.2.1 Fault Reporting

The network switch should be configured to monitor the Ethernet connections and power supply. This is

configured using DIP switches on the top of the unit.

1. Ensure switch 1 (PWR) and switch 2 (RPS) are ON.

2. Set switches 3 (P1) to 12 (P10) ON for each port that has a connection to the ASL Secure Loop, or

to a device that is part of the PAVA system.

The example below is configured for ASL Secure Loop connected to ports 9 and 10 (the SFP ports) and

VIPEDIA-12 connected to port 1.

For EN 54-16 compliance, the network switch must be configured to report faults as described

above and connected to an onboard or BMB01 fault contact input in the voice alarm system.

The PAVA system fault contact must be configured to active low.

NETWORK-SWITCH-LP01 – Configuration Guide

U-0641-3675.docx – Issue: 01 complete, approved

Page 6 of 28

2.2.2 SFP Speed

If SFPs are connected, the SFP ports must be configured with the connection speed that matches the SFP.

This is configured using DIP switches on the top of the unit. Switch A for port 9, and switch B for port 10.

•Set to ON if the SFP is 1000 Mbps.

•Set to OFF if the SFP is 100 Mbps.

NETWORK-SWITCH-LP01 – Configuration Guide

U-0641-3675.docx – Issue: 01 complete, approved

Page 7 of 28

3 Configuration

3.1 Login

To log in to NETWORK-SWITCH-LP01:

1. Power on and connect the configuration PC to the network switch.

2. Launch a web browser and enter the IP address of the network switch.

3. Enter the username and password, then click “Login”.

Default username and password:

•“User Name”: admin.

•“Password”: admin.



If the network switch has previously been configured, it is recommended to perform a factory reset

before continuing. If required, refer to section 5 APPENDIX – Factory Reset on page 26.

Do not connect network switches together until the configuration in the following sections is

complete for each unit.

This is to prevent configuration issues due to multiple network switches with the same IP address,

and to prevent data storm due to RSTP being disabled by default.



The default IP address for NETWORK-SWITCH-LP01 units is 192.168.2.5 and the netmask is

255.255.255.0.



For instructions on how to change the User Name and Password refer to the NETWORK-

SWITCH-LP01 User Manual.

NETWORK-SWITCH-LP01 – Configuration Guide

U-0641-3675.docx – Issue: 01 complete, approved

Page 8 of 28

3.2 IP Settings and Hostname

To configure the IP address, netmask, gateway address, and hostname of the NETWORK-SWITCH-LP01:

1. In the navigation tree, expand the “Basic Settings” item and select “System Settings”.

2. In the configuration window, configure as required:

•“Hostname”.

•“IP Address”.

•“Subnet Mask”.

•“Default Gateway”.

3. Click “Apply”.

4. The web browser may lose connection to the network switch at this point.

The IP and hostname changes are temporary and will be lost after a power cycle or reboot.

NETWORK-SWITCH-LP01 – Configuration Guide

U-0641-3675.docx – Issue: 01 complete, approved

Page 9 of 28

5. To reconnect to the network switch:

a. Configure the PC network interface as required to communicate with the new IP settings on

the network switch. For instructions, refer to section 4 APPENDIX – PC Requirements on

page 23.

b. Enter the network switch IP address.

6. Log in to the device.

7. Click the save icon in the top right corner of the configuration window.



The IP and name settings are now saved onto the device and may be powered off if required.

NETWORK-SWITCH-LP01 – Configuration Guide

U-0641-3675.docx – Issue: 01 complete, approved

Page 10 of 28

3.3 ASL Secure Loop (RSTP)

To configure ASL Secure Loop:

1. In the navigation tree, expand the “Advanced Settings” item.

2. Select “STP” item and the “General Settings” tab.

3. Set “State” to “Enable”.

4. Set “Mode” to “RSTP”.

5. Configure the primary and secondary root bridge by setting the “Priority” of the network switches:

•Primary root bridge: “4096”.

•Secondary root bridge: “8192”.

•Other network switches in the loop enter: “28672”.

6. Set “Forward Delay” to “25”.

7. Set “Max Age” to “40”.

8. Set “Hello Time” to “2” (default setting).

9. Click “Apply”.



Choose one network switch in the ASL Secure Loop to be the primary root bridge, and one to be

the secondary root bridge as follows:

•Primary root bridge: network switch that is connected to the VIPEDIA-12 or INTEGRA that is

critical for emergency broadcasts.

•Secondary root bridge: network switch that is on the opposite side of the loop from the

primary root bridge.

Inhaltsverzeichnis

Andere ASL INTERCOM Schalten Handbücher

ASL INTERCOM

ASL INTERCOM IS 640-18 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung