Assa Abloy Sargent 52-4424 Bedienungsanleitung

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

12/30/12

1 A8094B

S1/S2 Replacement Controller Instructions

52-4424, 52-4425, 52-4533, 52-4537

FOR INSTALLATION ASSISTANCE CONTACT SARGENT • 1-800-810-WIRE (9473) • www.sargentlock.com

1. On the inside of the door, remove the security screw from the battery

cover on the inside escutcheon (Fig. 1).

2. Lift and remove the battery cover (Fig. 1).

This controller has been conﬁgured as a generic replacement.

The serial number MUST be changed before it can be used!

(For serial conﬁguration, refer to Step 2 - Conﬁgure Serial Number )

NOTE: For S2 Controllers previously labeled 52-4426, use 52-4425 for the

replacement controller part number.

1 - Replace Controller

Fig. 1

6. Remove inside escutcheon assembly from door.

3a. For exit devices, continue to Step 4 (the inside lever handle does

not need to be removed in order to change the controller).

3b. For a cylindrical lock, remove the inside lever handle by inserting

the push-pin tool (provided with lock) as shown in Figure 2A.

3c. For a mortise lock, remove the inside lever handle by loosening

the lever handle set screw (Fig. 2B).

4. Remove top and bottom through-bolts from inside escutcheon.

5. Carefully separate escutcheon slightly from door and disconnect

antenna (iCLASS only), gray ribbon reader cable, green grounding wire,

motor harness, DPS harness (Fig. 2C), and hard-wired harness/PoE (if present).

Set Screw

Fig. 2B

Inside Lever

Inside of door

Push-Pin Tool

Fig. 2A

Fig. 2C

A8094B 2

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

FOR INSTALLATION ASSISTANCE CONTACT SARGENT • 1-800-810-WIRE (9473) • www.sargentlock.com

S1/S2 Replacement Controller Instructions

52-4424, 52-4425, 52-4533, 52-4537

6. Remove the four (4) Phillips screws holding the

original controller in place (Fig. 3).

Remove controller.

7. Seat the replacement controller into inside escutcheon.

Attach with the four (4) original Phillips screws.

8. Reconnect the keypad harness, ground wire, DPS

harness, motor harness, and hard-wired/PoE harness

(if present). See Figure 4.

9. Mount the inside escutcheon back on the door using

the two through-bolt screws (Fig. 4).

Reattach lever (if applicable).

10. Install batteries and battery keeper.

Fig. 3

Fig. 4

Through-bolt

1. Place (6) “AA” batteries in the compartment, being careful to align polarity properly (Fig. 5B)

2. Replace battery keeper being careful to engage tabs at top to hold it in place. (Fig. 5A)

Fig. 5A Fig. 5B

A8094B 3

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

FOR INSTALLATION ASSISTANCE CONTACT SARGENT • 1-800-810-WIRE (9473) • www.sargentlock.com

S1/S2 Replacement Controller Instructions

52-4424, 52-4425, 52-4533, 52-4537

1. Using Lock Conﬁguration Tool (LCT), connect to the

new controller.

2. From the main drop down (Fig. 6A), select “Conﬁgure

Serial Number”.

3. Click ‘Go’.

2 - Conﬁgure Serial Number

6. Click “Apply Serial Number (S/N)”.

7. Conﬁgure lock as usual.

8. Replace battery cover and install security screw.

Fig. 6B Conﬁgure Serial Number

Fig. 6A

4. Select the correct reader/human interface.

5. Select the correct lock body.

NOTE: Please conﬁrm last ﬁve (5) digits of serial number

match previous controller.

A8094B 4

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

FOR INSTALLATION ASSISTANCE CONTACT SARGENT • 1-800-810-WIRE (9473) • www.sargentlock.com

S1/S2 Replacement Controller Instructions

52-4424, 52-4425, 52-4533, 52-4537

1. Attach battery cover to inside escutcheon

making sure to line up tabs with retaining

slots in battery cover.

2. Secure with the security screw and tool

(P/N 01-0297) (Fig. 7A).

Security Tool

Retaining

slots

Tabs

Fig. 7A

3 - Replace Battery Cover

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Controller Handbücher

Assa Abloy

Assa Abloy Sargent P106 Bedienungsanleitung

Assa Abloy

Assa Abloy Incedo EAC-M90 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent IN100 Leitfaden

Assa Abloy

Assa Abloy LCU9016III Bedienungsanleitung

Assa Abloy

Assa Abloy CLIQ CLM Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 700 Bedienungsanleitung

Assa Abloy

Assa Abloy effeff TSB-Controller II Bedienungsanleitung

Assa Abloy

Assa Abloy InControl 3270 Bedienungsanleitung

Assa Abloy

Assa Abloy effeff 970-TSBC-30-10 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch