Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung
www.hkcsecurity.com
Security
Safe & Secure
An ASSA ABLOY Group brand
Universal GSM/WiFi
IP Communicator
2
Setting-up SecureComm...........................................................................................3
Commissioning the GSM-WiFi U - Standalone Mode................................................3
How to commission u
...........................................................10
......11
Technical Specifications...........................................................................................26
sing the
he HKC APP...........................
......................................................
SmartLink700 app...........................................4
Downloading t ................................................8
GSM-WiFiU Inputs & Outputs......... ........9
Example of Standalone Wiring........
Commissioning GSM-WiFi U - SecureWatch Mode.............................................
Wiring to SecureWatch Panel.....................................................................12
Menu Map for SecureWatch Panels.............................................................13
Communicators Menu - SecureWatch Panels.............................................14
SecureComm Menu - SecureWatch Panels................................................16
Commissioning GSM-WiFi U - SecureWave Mode....................................................18
Wiring to SecureWave Panel.......................................................................19
Menu Map for SecureWave Panels..............................................................20
Communicators Menu - SecureWave Panels...............................................21
SecureComm Menu - SecureWave Panels..................................................23
GSM & WiFi Status LEDs.............................................................................26
Contents
WARNING
While this system has been designed to the highest standards it does not offer guaranteed protection against burglary, fire or carbon
monoxide. Any alarm system is subject to compromise or failure to activate for a variety of reasons. Therefore, good installation practices and
regular maintenance are essential to ensure continuous satisfactory operation of the system. The transmission of messages is dependent on
the telecom service provider. HKC Security Ltd. cannot guarantee successful messaging. Messages which remain undelivered when the
validity period expires are discarded. The validity period is the time the message is submitted plus 12 hours.
COPYRIGHT
© HKC Security Ltd. All Rights reserved. No part of this publication may be reproduced, transmitted, stored in a retrieval system or translated
in another language in any form or by any means - electronic, mechanical or otherwise without the prior written permission of HKC Security
Ltd.
DISCLAIMER
HKC Security Ltd. makes no representations or warranties with respect to the contents hereof and specifically disclaim any implied warranties
of merchantability or fitness for any particular purpose. Further, HKC Security Ltd. reserve the right to revise this publication and to make
changes from time to time in the contents hereof without obligation of HKC Security Ltd. to notify any person of such revision.
This marking certifies that this product has been tested in a representative system complying with the requirements laid down in EMC
directive 2014/30/EU, RE Directive 2014/53/EU, RoHS directive 2011/65/EU and their amendments.
GSM-WiFiU Installation Manual Rev 2. 11th of November, 2020
SecureComm is HKC’s cloud-based communications service which greatly
enhances the capabilities of your system.
There are essentially 3 phases to setting up SecureComm connectivity. The first is to
setup the billing arrangements with the end user. Go to your internet browser and
type securecomm.hkc.ie into the address bar as illustrated.
Power-up the communicator as illustrated then press and hold the
Connect/Reset button for 5 seconds approx. until the WiFi and
GSM Status LEDs flash red - then release. When the LEDs are a
solid red, the unit has been factory defaulted. Next, briefly press the Connect/Reset
button again. This forces the unit to establish a GSM link to the SecureComm server
in the background. Initially, the GSM Status LED flashes orange for 15 minutes.
Here you will find an intuitive series of prompts which sets up basic account details.
Once
the process is complete, you will be issued with an installation ID number.
The second phase involves physically configuring the system i.e. powering-up the
GSM-WiFi Unit - see below and the following pages:
Also, if the end user wants, take this opportunity to select IP Reporting
Keep this
number safe for the moment
.
, it will be required later.
Setting up SecureComm
New Tab
securecomm.hkc.ie
X
Commissioning the GSM-WiFi U - Standalone Mode
112
2 3 4 5
D6
C
Inputs Outputs
Connect/Reset
Button
Press 1 sec. to Connect
or
Hold to Default
GSM Status
WiFi Status
Tamper
7
+ B 8
-A
12V
0V
100811811
S/N#
3
Essentially, you now have 15 minutes to match the GSM-WiFiU
communicator being commissioned to the relevant
SecureComm account.
Using the SmartLink700 app press the New Installation
START NOW icon
Next, select the GSM-WiFi Universal
option followed by the Commission New
GSM-WiFi Universal option.
Then, either type-in the serial number or scan the QR code
pattern from the label fitted on the circuit board.
Note: To scan the pattern, press the
Scan QR icon and place the phone’s
camera in front of the label. The
Serial Number box will auto-populate.
Type-in the SecureComm installation ID number - the one you
got when you established the billing details (page 3).
Commissioning the GSM-WiFi U - Standalone contd.
100811811
S/N#
!
1234567
100811811
4
As a minimum, you will also need to enter a Remote Code. This
remote access code will be required should you need to
reconfigure the unit in the future. Minimum length is 4
characters. Maximum length is 16. The characters can be letters
or numbers.
If you are enabling IP reporting then contact your monitoring
company (ARC), get an account number and put it into Account
Code section here.
Note: Remember to select the IP reporting option in the
securecomm.hkc.ie portal.
If the end user wants the option of control via the HKC APP they
will need a 4 to 6 digit (i.e. numerals) User Code - similar to a
traditional arm/disarm code. The “0" digit may be used.
A SecureComm Password, chosen by the installation engineer,
must also be entered. The minimum length of the password is 4
characters. Maximum length is 16. The characters can be letters
or numbers.
when the HKC APP is being set up.
Keep this password safe for the moment, it will
be required
Finally, press the Connect icon.
Commissioning the GSM-WiFi U - Standalone contd.
1234567
1234567
100811811
100811811
18867
18867
2222
2222
Wait a few moments while the customer’s details are read from
the SecureComm server.
Note: If the unit cannot connect to the SecureComm server, you may
have to briefly press the Connect/Reset button again.
Note: When the unit is successfully commissioned the GSM Status LED
will flash green. Each flash represents 20% network coverage (e.g. 4
flashes = 80%).
1234567
100811811 !
!
!
5
Commissioning the GSM-WiFi U - Standalone contd.
The customer’s details will auto-populate the relevant fields.
When complete press the Save icon.
So far, the system is only setup using the GSM network. For full
connectivity it should also be connected to a WiFi network.
Therefore...
You will see the new site added to your customer list. To add
WiFi connectivity click on the customer in question - in this
example “Sheehan’s”.
Then click on the red cloud icon to connect to the communicator.
1234567
Sheehan’s
Vincent
Walsh
Mary Sheehan
Serial Number:
SecureComm ID:
Type:
Version: 1.0.0.19
GSM-WiFi Universal
1234567
100811811
6
Commissioning the GSM-WiFi U - Standalone contd.
Press the Scan WiFi Networks icon.
The system will take about 30 seconds to scan the premises for
WiFi routers. When complete, select the router in question, enter
the router’s password and press Connect.
Then go to COMMUNICATORS and select WiFi.
sheehan home (Signal Level: 5)
7
Note: When the unit is successfully connected, WiFi Status LED
will flash green. Each flash represents 20% WiFi coverage (e.g. 4
flashes = 80%).
!
Commissioning the GSM-WiFi U - Standalone contd.
1234567
100811811
1234567
End User’s phone
Installer’s phone Installer’s phone
Once the end user has downloaded the HKC APP they will be guided to a page
where they input the installation ID (the one from page 3 of this manual) and the
password chosen by the installation engineer (from page 5 of this manual).
When done, press the Connect icon. The HKC APP is now ready to go.
To login to the site, enter the User Code that was programmed on page 5.
The GSM-WiFiU unit is now live and ready for the 3rd and final phase which
involves the end user downloading the HKC APP from: Google play®, or Apple’s
App Store®.
Note: To find the HKC APP quickly, search for HKC SecureComm in both stores.
!
8
112
2 3 4 5
D6
C
Inputs Outputs
Connect/Reset
Button
GSM Status
WiFi Status
Tamper
7
+ B 8
-A
12V
0V
0V 0V 0V 0V 0V 0V 0V 0V
100811811
S/N#
Commissioning the GSM-WiFi U - Standalone contd.
When an input is pulled down to 0V as illustrated, it is in the normal Restored state.
Removing this 0V i.e. when a switch is opened, the voltage on the terminal will pull
up to 3V and will Activate the input. These inputs are fully programmable through the
SmartLink700 App. The input triggers can also be changed so that they will activate
when 0V is applied and restore when 0V is removed. It is also possible to apply 12V
to an input to activate it. Input activations can also be delayed by up to 60 minutes.
The default input types are:
There are also 2 relay Outputs on the unit. Output 1 is a programmable Normally
Open output that by default follows the onboard tamper switch, and will also open if
a fault is detected on the GSM or Wi-Fi path. This output will be closed when the
tamper is closed and there are no faults detected on the communication paths. This
output will open if power is lost to the unit.
These outputs are fully programmable through the SmartLink700 App. The outputs
can also be inverted if required.
Output 2 is normally closed-circuit. It can be wired into a Key input and can be
controlled by the HKC app i.e., when it goes open-circuit it will arm a typical control
panel and when it goes closed-circuit it will disarm the panel.
Ireland
1 Fire
2 Panic
4 Arm/Disarm
5 Zone Inhibit
6 Mains Fail
8 Tamper
3 Verified Alarm
7 Pre-Alarm
United Kingdom
1 Fire
2 Panic
4 Open/Close
5 Zone Omitted
6 Mains Fail
8 Tamper
3 Intruder Alarm
7 Confirmed Alarm
9
Note: Slightly different
phraseology used in
Ireland and the UK.
!
Example of Standalone Wiring - non-EN compliant
112
2 3 4 5
D6
C
Inputs Outputs
GSM Status
WiFi Status
Tamper
7
+ B 8
-A
100811811
S/N#
+
-
12V
Control Panel
Fire o/p
Panic o/p
Alarm o/p
Arm/Disarm o/p
Zone programmed
for “Line Fault”
Zone programmed
for “Key”
Note: Given
that a GSM or
WiFi fault is
more likely
than a tamper
activation,
choose this
zone for “Line
Fault”.
Note: Make
sure these are
programmed
as positive
trigger.
!
!
!
Note: Choose either input 3
or 7 depending on your
monitoring company’s
preferred “channel” for a
verified alarm signal.
!
10
Remove the
mains and
battery
supply before
fitting the
GSM-WiFiU
unit
Inhaltsverzeichnis
