ASTEL MGR100 Bedienungsanleitung

MGR100

GSM

REMOTE

CONTROL

UNIT

Operating Instructions

CONTENTS

Preface............................................................................................................................................... 3

Features............................................................................................................................................. 3

Precautions ........................................................................................................................................ 3

Controls And Connectors ................................................................................................................... 4

Installation .......................................................................................................................................... 5

DC power supply and Accumulator connection............................................................................ 5

Control connections ..................................................................................................................... 6

Relays connection ................................................................................................................. 6

Digital outputs connection...................................................................................................... 6

Alarm connections ....................................................................................................................... 7

Digital inputs connection........................................................................................................ 7

Analog inputs connection.......................................................................................................7

Temperature sensors connection .......................................................................................... 8

Other connections........................................................................................................................ 8

Speaker and Microphone connection .................................................................................... 8

Remote keyboard connection................................................................................................ 8

I2C bus connection................................................................................................................ 9

RS-232 connection ................................................................................................................ 9

Instructions....................................................................................................................................... 10

Login.......................................................................................................................................... 10

Controls ..................................................................................................................................... 10

Relays.................................................................................................................................. 10

Digital outputs...................................................................................................................... 11

Alarms........................................................................................................................................ 12

Digital inputs........................................................................................................................ 12

Analog inputs....................................................................................................................... 13

Temperature sensors .......................................................................................................... 14

GPS receiver ....................................................................................................................... 15

Other alarm functions................................................................................................................. 17

Alarm set-up .............................................................................................................................. 19

Other functions .......................................................................................................................... 19

DTMF instructions...................................................................................................................... 21

SIM card locations ..................................................................................................................... 22

Technical Specifications................................................................................................................... 24

Optional Accessories........................................................................................................................ 24

Warranty........................................................................................................................................... 25

Declaration Of Conformity................................................................................................................ 26

_______________________________________________________________________________________________

PREFACE

The MGR100 is a high-efficient GSM remote

controller specially designed to use in nautical

applications. Built-in GSM module with

different interfaces enable simple and easy

control and management of complete yacht

electrical and electronic equipment through

GSM mobile phone. Built-in relays enable

remote control of different yacht devices. Alarm

inputs enable remote control of different yacht

systems like pumps, engines and other

systems, voltage measuring and measuring of

temperature and humidity. By the help of

optional GPS receiver the position

management and tracking are enable and

alarming in the case of leaving or approaching

to the hold position.

The control of the unit is possible by the help of

SMS text messages or by the help of tone

(DTMF) dialing. Alarming is possible by

receiving the SMS text messages or by alarm

calls or by the combination of both of them.

Interactive voice responder confirms the

requests during DTMF control or inform about

the kind of alarm when alarm occurs. The unit

enables also speaker and microphone

connection to remote communication.

Programming is possible by the help of SMS

text messages or with PC by the help of RS-

232 serial interface.

This GSM Remote Control Unit comes in three

versions, Basic, Advance and Reference,

every model is available also with GPS

receiver.

FEATURES

built-in GSM module with SIM interface

built-in GPS module for position

management and alarming***

SMS control

DTMF (PSTN, ISDN, GSM) control*

IVR – interactive voice responder**

temperature measuring and management*

analog voltage measuring and

management*

alarm sensor management

remote keyboard interface

speaker and microphone interface**

PC remote and local management**

wide range power supply

ABS casing

accumulator connection

PRECAUTIONS

The remote control unit has to be installed

and used in accordance with the

instructions of this manual only.

The power supply has to be disconnected

before installation.

Avoid using the remote control unit under

the presence of appliances generating

strong magnetic fields like radar, wheather

station and in places subject to direct

sunlight.

Do turn power off immediately and refer

servicing to qualified service personnel if

the remote control unit does not operate

normally following the operating

instructions.

CONTROLS AND CONNECTORS

(1) DIGITAL IN

Terminal block to connect 8 different sensors.

(2) OPEN C.*

Terminal block to connect 4 different relays or

other control units.

(3) RELAY*

Terminal block to connect 4 different devices.

(4) DC - ACCU

Terminal block to connect Accumulator and DC

power supply.

(5) GPS antenna connector***

SMA connector to connect GPS antenna.

(6) Status LED

LED to show the status, LED blinks in normal

operation.

(7) Alarm LED

LED to show the alarm status, lights when

alarm occurs.

(8) GSM antenna connector

SMA connector to connect GSM antenna.

(9) RS-232**

Terminal block to connect RS-232 control

equipment.

(10) SP – MIC**

Terminal block to connect Speaker and

Microphone.

(11) REMOTE**

Terminal block to connect external keyboard.

(12) ANALOG IN*

Terminal block to connect 4 different voltage

sources.

(13) I2C**

Terminal block to connect I2C control

equipment.

(14) SENSOR*

Terminal block to connect 3 temperature or

other sensors.

(15) GSM module LED

LED to show the GSM module status, lights in

normal operation..

INSTALLATION

All the diagrams in this manual show the installation of the GSM Remote Control Unit, model

MGR100G REFERENCE.

Note:

The main DC power supply has to be switched off before installation.

Also refer to the instruction manual of the equipment to be connected.

The total power consumption of all sensors, relays and other devices supplied from the

unit has not exceed 500mA.

The MGR100 series remote control unit have to be installed near the control board. Avoid the

installation in engine room, extremely hot places and near appliances generating strong magnetic

fields. The installation have to be realize by a qualified personel.

Note:

The GSM and GPS antennas have to be connected before the unit is switched-on.

The SIM card have to be inserted before the unit is switched-on. The SIM location 3

(password) has to be empty. The PIN code request have to be disabled.

DC power supply and Accumulator connection

The power supply have to be connected to the DC terminal block connector with right polarity and

protected with a fuse (not included). The power supply voltage have to be from 12 - 30VDC. The

back-up accumulator have to be connected to the ACCU terminal block connector with right polarity

and also protected with a fuse (not included).

Note:

The declared accumulator voltage have to be the same as the DC power supply voltage.

F0.5A F0.5A

Control connections

Relays connection*

The relay control outputs are suitable to control four different yacht electrical and electronic devices,

connected directly or through external relays. First two relays have NO and NC contacts, other two

relays have only NO contacts.

Note:

The total DC curent consumption of connected equipment to each relay must not exceed

1A when the equipment are controlled directly from the unit. The maximum voltage

connected to the relays must not exceed 30V.

Digital outputs connection*

The digital outputs are suitable to control four different yacht electrical and electronic devices

connected through external relays.

Note:

The total DC curent consumption of each connected relay must not exceed 100mA.

PP P

P+

GND

Alarm connections

Digital inputs connection

The digital inputs are suitable to connect eight different sensors like IR intruder sensors, smoke

sensors, water inlet sensors (floating switches) with NO or NC contacts. The sensors can be supplied

directly from the unit and connected to one of +ACCU terminal block.

Note:

The total power consumption of each sensor supplied from the unit must not exceed

100mA.

Analog inputs connection*

The analog inputs are suitable to connect four different voltage sources like are boat accumulators

and to measure their voltages.

Note:

Only the DC voltage can be connected to the analog inputs.

The maximum DC voltage connected to each input must not exceed 30Vdc.

S1 S3 S5 S7

S2 S4 S6 S8

Temperature sensors connection*

The unit is designed to connect maximum three temperature sensors to measure the temperature in

different places like are engine room, saloon, rooms and cockpit or fly-bridge.

Note:

Only the specified sensors can be connected to the temperature sensors inputs.

Other connections

Speaker and Microphone connection**

The unit is designed to connect the microphone which enables to listen the voice and low-power

speaker for communication and notification.

Note:

Only the specified speaker and microphone can be connected to the unit.

Remote keyboard connection**

The unit is designed to connect the simple remote keyboard which enables operating with the unit to

enable and disable the alarming and other functions.

Note:

Only the specified remote keyboard can be connected to the unit.

T1 T2 T3

I2C bus connection**

The unit is designed to connect also the devices using the I2C protocols.

Note:

Only the devices using I2C protocol can be connected to the I2C interface.

RS-232 connection**

The unit is designed to connect also the devices using the RS-232 serial interface control like

personal computer or other devices.

Note:

Only the devices using RS-232 serial interface can be connected to the RS-232 port.

KEYBOARD

I2C bus

device

INSTRUCTIONS

The default setting of password is 1234.

To send the password

PWDxxxx x=1..9

PWD1234 (if the password is 1234)

(PWD instruction should be uppercase, other instructions uppercase or lowercase)

PWD1234_instr1_instr2_instr3

(first should be sent the password then space and then instructions)

To change the password

NPWxxxx x=1..9

NPW2222 (if the new password is 2222)

Controls

Relays*

To receive a status of relays:

REL

Received SMS:

NAME

REL1:REL1:12.10.00

REL2:REL2:ON

REL3:REL3:OFF

REL4:REL4:REM

To switch-on the relay:

RELxON x=1..4

REL1ON (to switch-on the relay 1)

To switch-off the relay:

RELxOFF x=1..4

REL1OFF (to switch-off the relay 1)

To switch-on the relay for selected time duration:

RELxONhh.mm x=1..4

hh=0..24

mm=0..60

ss=0..59

REL1ON12.10.00 (to switch-on the relay for 12 hours, 10 minutes)

Inhaltsverzeichnis

Andere ASTEL Steuereinheit Handbücher

ASTEL

ASTEL TGR 100 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung