Aston Global SD908 Montageanleitung

Shower Door Model Number :SD908

INSTALLATION AND OWNER'S MANUAL

Please carefully read these instructions before you begin to install the products.

01/12 Rev B

P/N:10055-06

Thank you for purchasing your Aston shower door and tray. We hope that it will

provide you with years of satisfying use and enjoyment.

Please read this manual carefully because it contains information and instructions

about the proper installation of the unit. If you do not follow certain conditions of

installation and maintenance, your warranty may be affected.

Aston Shower door's and shower tray's feature:

ϒ⁄ Tempered Safety Glass

ϒ⁄ High quality hardware

ϒ⁄ Easy maintenance durable fiberglass reinforced acrylic

Before you start

SUPPLIED HARDWARE

SUPPLIED PARTS

SCREW PACK

(2)

SCREW PACK

(3)

M5x16.5

SCREW PACK

(4)

M4x40

expand tube

M4x12

SCREW PACK

(1) 8

M4x30 8

Please read and follow the installation instructions and guidelines in this section.

Failure to follow the recommended instructions and installation techniques may

lead to possible damage to the unit or the surrounding area and can affect

warranty claims.

ATTENTION: This unit requires assembly. A minimum of two people are

required for assembly, as several of the sections can be large and unstable until

assembled.

You will need the following tools:

ϒ⁄ Drill with screwdriver attachments

ϒ⁄ Caulk gun

ϒ⁄ Level (3 foot or longer is recommended)

ϒ⁄ Tape measure

ϒ⁄ Phillips head screw driver

ϒ⁄ Flat head screw driver

Installation Guide

75"

212"

36"

1235"

ϒ⁄ Bathroom rated silicone sealant

Before starting the installation, please ensure that you have inspected all

components of the unit and check for broken or damaged sections. If you find

damage, please contact your dealer or the manufacturer.

Locate the accessory and manual box and remove the individual screw and

hardware packages and lay them out in sequential order to aid in completing

the rest of the installation

The shower tray needs to sit on a flat level base for proper support. Ensure that

the area for the shower tray is properly prepared for installation.

Using the drawing provide place the floor drain in the proper location so that the

shower tray drain and the floor drain are in line after final installation.

Place the shower tray in the final installation position line up the drain holes and

check for level. If not level make adjustments to the floor at this time.

Preparation of base

for installation of shower tray

1. Remove and inspect all of the glass panels. If any are broken, please contact

your dealerorthe manufacturer.

NOTE: Theglasspanels are labeled to indicate the direction for the topofthe

glass panels.

2. Remove and inspect the aluminum top and bottom rails for the glass

assembly.

NOTE: Thealuminumrailsare labeledtodistinguish the top and bottom railand

their orientation within the assembly.

IMPORTANT: Please take note that Screw Pack contains several different

lengths of screws each for a specific location within the glass assembly.

During the next steps of assembly, pay close attention so the correct screw

length is used in the correct location. Failure to do this cancausedamage to

the glass panels and possibly result in leaks.

Assemble the glass panel

M5x16.5mm

SCREW PACK

(1)

3. Place the bottom aluminum rail on the floor with correct orientation up to

receive the glass panel.

4. Apply a liberal bead of sealant on the bottom rail from the slot that receives

the glass panel out to the end oftherail.

NOTE: The next steps of assembly will require two people.

5. Side glass panel and insert it into the slot onthebottomrail.

6. Take the top aluminum rail and apply a liberal bead of sealant from the slot

for the glass panel out to the end oftherail.

7. Line up the slot on the top rail with the receiving tabs on the glass panel and

insert the top rail on to the glasspanels.

8. Apply some sealant to the end of the aluminum channels, then u sing the

screws provided follow the diagram to insert the correct screw length in to the

correct location.

M4X30mm

SCREW PACK

(2)

9. After all the screws are in place and secure, wipe any excessivesealant and

use the excess to fill any cracks or gaps betweenthejoints.

10. Cover the exposed screw heads with decorative plastic screwheadcovers

Place the assembled glass wall panel onto the shower tray and mark the predrilled

holes onto the wall. Remove after marking the walls.

Mark the Glass panel mounting holes

Inhaltsverzeichnis

Beliebte Tür Handbücher anderer Marken

ENFORCER

ENFORCER Enforcer SK-990A Bedienungsanleitung

Electri-Chef

Electri-Chef TR18 Betriebsanleitung

BEA

BEA PBR45x Bedienungsanleitung

GE 19298 Bedienungsanleitung

Sterling Plumbing

Sterling Plumbing Frameless Bypass Shower Door SP5465-45 Bedienungsanleitung

GE 19214 Bedienungsanleitung

Ives

Ives 55 Bedienungsanleitung

Algoma Hardwoods

Algoma Hardwoods STC 39 Bedienungsanleitung

Ives

Ives Surface Bolt 43 Bedienungsanleitung

Therma-Tru

Therma-Tru Double-door Bedienungsanleitung

Erreka

Erreka PREMIS 200 Bedienungsanleitung

Ives

Ives Surface Bolt 144 Bedienungsanleitung

Lennox Hearth Products

Lennox Hearth Products MPB-35 Bedienungsanleitung

Ives

Ives Offset Top Pivot 7245F Bedienungsanleitung

KitchenAid

KitchenAid KBAU181V Handbuch

Ives

Ives 670 Bedienungsanleitung

Ives

Ives Mortise Bolt S48 Bedienungsanleitung

American Standard

American Standard Acrylux 6000Y1.BE5 Bedienungsanleitung