Asus AAEON PICO-APL4-SEMI Bedienungsanleitung

Quick Installation Guide

PICO-APL4-SEMI

This document will guide you through

the basic installation process for your

new PICO-APL4-SEMI.

PICO-APL4-SEMI

Item Description Remark/PN

PICO

-APL4 Board MB

Top Chassis

M17KBU4000

Bottom

Chassis M17KBU4010

Cooler

17592SEMI1

Accessory kits

Power Button Cable x1

1709100109

Screw.M3. Black x8pcs

S1D3004031

Screw.M3

Nickel x4pcs S1D5106010

Packing

2 3 41 5

PICO-KBU4-SEMI Quick Installation Guide

Install Guide Steps

Step 1: On the thermal assembly, remove the plastic covering as shown.

Step 2: Place the top chassis onto the thermal assembly. Note the orientation of the chassis with the thermal

assembly. Secure with four black screws.

Step 3: On the PICO-APL4 board, remove the nut and washer from the power input port.

Step 4: Connect the thermal fan cable to the

PICO-APL4 board as shown.

Step 5: Insert the PICO-APL4 board into the chassis

assembly with the processor side toward the thermal

assembly. DO NOT place the CMOS battery between

the board and thermal assembly.

Step 6: Check that the I/O ports are properly aligned. Secure board with four nickel screws.

Step 7: Thread the power button cable through the hole for the power button. Plug the cable into the

front panel connector (the 2nd connector from the front, CN3 in user manual), then gently push the

power button in until it is secure (you will hear a ‘snap’). NOTE: Be careful not to tangle the power

button cable with the CMOS battery cable.

Step 8: Peel the backing off of the tape on the CMOS battery. Gently press the battery onto the PICO-

KBU4 board to secure it.

Step 9: Attach the bottom chassis by first lining up the right side, then swivel the chassis into place.

NOTE: the bottom chassis does not slide directly on, it must swivel into place as shown in the figure.

Step 10: Ensure the bottom chassis is properly lined up and attached. Use black screws to secure, two

screws on the bottom and one screw on the left and right sides of the chassis.

Step 11: Replace the washer and nut for the power input port.

Dieses Handbuch passt für folgende Modelle

Andere Asus Industrie-PC Handbücher

Asus

Asus AAEON BOXER-6840-CFL Bedienungsanleitung

Asus

Asus Aaeon BOXER-6641-A1-1110 Bedienungsanleitung

Asus

Asus AAEON BOXER-6642-CML Bedienungsanleitung

Asus

Asus Aaeon BOXER-8254AI Bedienungsanleitung

Asus

Asus EBE-4U Bedienungsanleitung

Asus

Asus EBE-4U Bedienungsanleitung

Asus

Asus AAEON BOXER-8221AI-B Bedienungsanleitung

Asus

Asus AAEON PICO-EHL1 Bedienungsanleitung

Asus

Asus Aaeon EPIC-CFS7-PUC Bedienungsanleitung

Asus

Asus Aaeon BOXER-6639M Bedienungsanleitung

Asus

Asus Aaeon GENESYS-APL7 Bedienungsanleitung

Asus

Asus Aaeon BOXER-8331AI Bedienungsanleitung

Asus

Asus AAEON BOXER-6615 Bedienungsanleitung

Beliebte Industrie-PC Handbücher anderer Marken

Chipsee

Chipsee PPC-A72-101 Bedienungsanleitung

Advantech

Advantech UNO-2184G Bedienungsanleitung

MSI

MSI MS-9A76 Bedienungsanleitung

Stackrack

Stackrack THOR200 Bedienungsanleitung

Moxa Technologies

Moxa Technologies DA-682C Series Bedienungsanleitung

Nodka

Nodka eBOX-3000-ETC Bedienungsanleitung

Siemens

Siemens SIMATIC IPC627E Bedienungsanleitung

Artila

Artila Matrix-516 Bedienungsanleitung

MSI

MSI MS-9A89 Bedienungsanleitung

Siemens

Siemens SIMATIC Rack PC 840 V2 Bedienungsanleitung

Advantech

Advantech IPPC-6152A Bedienungsanleitung

Beckhoff

Beckhoff CX9020 Bedienungsanleitung

Dell

Dell Embedded Box PC 5000 Bedienungsanleitung

IBASE Technology

IBASE Technology ASB200-918 Series Bedienungsanleitung

Lenovo

Lenovo ThinkCentre M90q Betriebsanleitung

IXXAT

IXXAT Econ 100 Bedienungsanleitung

Kontron

Kontron KBox A-151-TGL Bedienungsanleitung

AXIOMTEK

AXIOMTEK ICO500-518 Series Bedienungsanleitung