Asus A7V-VM Gebrauchsanweisung

A7V-VM

Athlon® / Duron®

MicroATX Motherboard

Quick Start MANUAL

E854

2A7V-VM User’s Manual

1. FEATURES

Specifications

1. FEATURES

1.1 The A7V-VM Motherboard

The A7V-VM motherboard is carefully designed for the demanding PC user who

wants high-performance features in a small package.

1.1.1 Specifications

•AMD Athlon™/Duron™ Processor Support: Supports AMD Athlon™/

Duron™ processor designed for the AMD Athlon™/Duron™ Processor Mod-

ule (462-pin Socket A).

•North Bridge System Chipset: VIA VT8365A™ (ProvSavage KM133) inte-

grated system controller with AGP 4x Graphics core supports a 266MHz Front

Side Bus (FSB), supports up to 1.5GB of PC133 SDRAM/Virtual Channel

Memory (VCM) SDRAM, complies with AGP 2.0 specifications for 4X, 2X,

and 1XAGPmodes and PCI 2.2. bus interface with support for 5 PCI masters. It

is optimized to deliver enhancedAMDAthlon™/Duron™ processor system per-

formance.

•South Bridge System Chipset: VIA VT82C686B PCIset with PCI Super I/O

integratedperipheralcontroller supportsUltraDMA/100,whichallows burstmode

data transfer rates of up to 100MB/sec.

•PC100/PC133 Memory Support: Equipped with two DIMM sockets to

support PC100/PC133-compliant SDRAMs (16, 32, 64, 128, 256, 512MB) up

to 1GB.

• Super Multi-I/O: Provides two high-speed UART compatible serial ports and

one parallel port with EPP and ECP capabilities.

•Expansion Slots: Provides three 32-bit PCI 2.2 slots and one AGP expansion

slot. PCI supports up to 133MB/sec maximum throughput. Each PCI slot can sup-

port a Bus Master PCI card, such as a SCSI card.

•Wake-Up Support: Supports Wake-On-LAN activity with onboard network

support.

•AGP Slot: Supports an Accelerated Graphics Port card for high performance

component level interconnect targeted at 3D graphical display applications us-

ing 4X, 2X, or 1X mode bus.

•USB: Supports up to 4 USB ports, two on the back panel and two midboard for

more peripheral connectivity options.

•UltraDMA100/66/33: Comes with an onboard PCI Bus Master IDE controller

with two connectors that support four IDE devices on two channels. Supports

UltraDMA100/66/33, PIO Modes 3 & 4 and Bus Master IDE DMA Mode 2, and

Enhanced IDE devices, such as DVD-ROM, CD-ROM, CD-R/RW, LS-120, and

Tape Backup drives.

•Onboard LAN Controller: Features the Realtek 10/100Mb Fast Ethernet Con-

troller, which supports Wired for Management, remote wake-up, and OnNow

initiative to reduce Total Cost of Ownership (TCO).

A7V-VM User’s Manual 3

1. FEATURES

Specifications

•OnboardAudio: HardwareAC’97 V2.1 CODEC compliant, Crystal’s 3D sound

circuitry, sample rate conversion from 7kHz to 48kHz.

1.1.2 Performance

• 100MHz/ 100MHzand 133MHz/133MHzSynchronousHost/DRAMClock

Support: CPU frequency can operate at 133MHz while system memory

operates at 133MHz.

•Concurrent PCI: Concurrent PCI allows multiple PCI transfers from PCI mas-

ter buses to memory to CPU.

• SDRAM Optimized Performance: This motherboard supports Synchronous

Dynamic Random Access Memory (SDRAM), which increases the data transfer

rate of 800MB/s max using PC133-compliant SDRAMs.

• ACPI Ready: ACPI (Advanced Configuration and Power Interface) provides

more Energy Saving Features for future operating systems (OS) supporting OS

Direct Power Management (OSPM) functionality. With these features imple-

mented in the OS, PCs can be ready around the clock, yet satisfy all the energy

saving standards. To fully utilize the benefits of ACPI, an ACPI-supported OS,

such as Windows 98, must be used.

• New Compliancy: Both the BIOS and hardware levels of the motherboard meets

PC 99 compliancy. The new PC 99 requirements for systems and components are

based on the following high-level goals: Support for Plug and Play compatibility

and power management for configuring and managing all system components,

and 32-bit device drivers and installation procedures for Windows 95/98/NT/ME/

2000/XP.

1.1.3 Intelligence

• Fan Status Monitoring and Alarm: To prevent system overheat and system

damage, the CPU, power supply, and system fans can be monitored for RPM

and failure. All the fans are set for its normal RPM range and alarm thresholds.

• Remote Ring On (requires modem): This allows a computer with this mother-

board to be turned on remotely through an internal or external modem. With this

feature, users can access their computer from anywhere in the world!

4A7V-VM User’s Manual

2. HARDWARE SETUP

Motherboard Layout

2. H/W SETUP

FLOPPY

PRIMARY IDESECONDARY IDE

HP_PANEL

A7V-VM

Audio

Codec

Buzzer

VIA

VT82C686B

Chipset

DIMM Socket 1 (64/72-bit, 168-pin module)

DIMM Socket 2 (64/72-bit, 168-pin module)

CPU_FAN

Accelerated Graphics Port (AGP)

VIA

VT8365A

Chipset

CR2032 3V

Lithium Cell

CMOS Power

PS/2

T: Mouse

B: Keyboard

COM2

HP_USB

USB

T: USB1

B: USB2

Top:

RJ-45

DUCT_FAN

PCI Slot 1

PCI Slot 3

PCI Slot 2

AUX

Realtek

Fast

Enternet

CLRTC

GAME_AUDIO

Mic

Line

Out

Line

PS_FAN

SPEAKER

ATX Power Connector

WOLCON

Socket A

Flash EEPROM

(Programable BIOS)

CPU_TYPE

LCDTV

COM1

PARALLEL PORT

VGA

2.1 A7V-VM Motherboard Layout

A7V-VM User’s Manual 5

2. HARDWARE SETUP

Layout Contents

2. H/W SETUP

2.2 Layout Contents

Expansion Slots

1) DIMM1, DIMM2 p. 8 168-Pin DIMM Memory Support

2) Socket A p. 9 Central Processing Unit (CPU)

3) PCI1, PCI2, PCI3 p.10 32-bit PCI Bus Expansion Slots

4) AGP p.12 Accelerated Graphics Port

Connectors

1) PS2KBMS p.13 PS/2 Mouse Connector (6-pin female)

2) PS2KBMS p.13 PS/2 Keyboard Connector (6-pin female)

3) USBLAN p.14 Fast-Ethernet Port Connector

4) USBLAN p.14 Universal Serial Bus Ports 0 & 1 (Two 4-pin female)

5) PRINTER p.14 Parallel Port Connector (25-pin female)

6) COM1/COM2 p.15 Serial Port Connectors (9 pins, 10-1 pins)

7) GAME_AUDIO p.15 Game/MIDI Connector (15-pin female)

8) GAME_AUDIO p.16 Audio Port Connectors (Three 1/8”female)

9) VGA p.16 Monitor Output Connector (15-pin female)

10) PRIMARY/SECONDARYIDE p.17 Primary/Secondary IDE Connectors (Two 40-1pins)

11) PS_, CPU_, DOCT_FAN p.18 PowerSupply, CPU, ChassisFanConnectors(Three3-pin)

12) FLOPPY p.18 Floppy Disk Drive Connector (34-1pins)

13) HP_USB p.19 USB Header (12-2 pins)

14) CD,AUX, MODEM p.19 Internal Audio Connectors (Three 4 pins)

15) ATXPWR p.20 ATX Power Supply Connector (20 pins)

16) LCDTV p.20 LCDTV Headers (18 pins, 18-1 pins)

17) MLED (PANEL) p.21 System Message LED Lead (2 pins)

18) SMI (PANEL) p.21 System Management Interrupt Switch Lead (2 pins)

19) SPK (PANEL) p.21 System Warning Speaker Connector (4 pins)

20) RESET (PANEL) p.21 Reset Switch Lead (2 pins)

21) PLED (PANEL) p.21 System Power LED Lead (3 pins)

22) IDELED (PANEL) p.21 IDE Activity LED Lead (2 pins)

23) PWR (PANEL) p.21 ATX Power / Soft-Off Switch Lead (2 pins)

6A7V-VM User’s Manual

2. HARDWARE SETUP

2.3 Hardware Setup Procedure

Before using your computer, you must complete the following steps:

•Check Motherboard Settings

•Install Memory Modules

•Install the Central Processing Unit (CPU)

•Install Expansion Cards

•Connect Ribbon Cables, Panel Wires, and Power Supply

WARNING! Computer motherboards and expansion cards contain very delicate Inte-

grated Circuit (IC) chips. To protect them against damage from static electricity, you

should follow some precautions whenever you work on your computer.

1. Unplug your computer when working on the inside.

2. Use a grounded wrist strap before handling computer components. If you do not have

one, touch both of your hands to a safely grounded object or to a metal object, such as

the power supply case.

3. Hold components by the edges and try not to touch the IC chips, leads or connectors, or

other components.

4. Place components on a grounded antistatic pad or on the bag that came with the compo-

nent whenever the components are separated from the system.

5. Ensure that the ATX power supply is switched off before you plug in or remove the

ATX power connector on the motherboard.

Motherboard Settings

2. H/W SETUP

A7V-VM User’s Manual 7

2. HARDWARE SETUP

2. H/W SETUP

System Memory

2.4 System Memory (DIMM)

NOTE: No hardware or BIOS setup is required after adding or removing memory.

This motherboard uses only Dual Inline Memory Modules (DIMMs). Sockets are

available for 3.3Volt (power level) unbuffered Synchronous Dynamic Random Ac-

cess Memory (SDRAM) of 16, 32, 64, 128MB, 256 or 512MB to form a memory size

between 16MB and 1GB. One side (with memory chips) of the DIMM takes up one

row on the motherboard.

To use the chipset’s Error Checking and Correction (ECC) feature, you must use a

DIMM with 9 chips per side (standard 8 chips/side + 1 ECC chip).

Install memory in any combination as follows:

Location 168-pin DIMM Total Memory

DIMM1 (Rows 0&1) SDRAM 16, 32, 64, 128, 256, 512MB x1

DIMM2 (Rows 2&3) SDRAM 16, 32, 64, 128, 256, 512MB x1

Total System Memory (Max 1GB) =

2.5.1 General DIMM Notes

•This motherboard supports SPD (Serial Presence Detect) DIMMs. This is the

memory of choice for best performance vs. stability.

•This motherboard does NOT support registered memory.

•SDRAM chips are generally thinner with higher pin density than EDO (Ex-

tended Data Output) chips.

•Single-sided DIMMs come in 16, 32, 64,128, 256MB; double-sided come in 32,

64, 128, 256, 512MB.

•For optimum signal integrity, inserting the DIMMs in the following order is

recommended: DIMM1, DIMM2.

•SDRAMs used must be compatible with the current PC133/PC100 SDRAM

specification.

IMPORTANT

8A7V-VM User’s Manual

2. HARDWARE SETUP

2.4.2 DIMM Memory Installation

Insert the module(s) as shown. Because the number of pins are different on either

side of the breaks, the module will only fit in the orientation shown. DIMM mod-

ules are longer and have different pin contact on each side and therefore have a

higher pin density. SIMM modules have the same pin contact on both sides.

A7V-VM

A7V-VM 168-Pin DIMM Sockets

Lock

20 Pins

60 Pins

88 Pins

TheDIMMs mustbe3.3VUnbufferedfor thismotherboard.To determinetheDIMM

type, check the notches on the DIMMs (see figure below).

168-Pin DIMM Notch Key Definitions (3.3V)

DRAM Key Position Voltage Key Position

Unbuffered

RFU

Buffered Reserved

3.3V

5.0V

The notches on the DIMM module will shift between left, center, or right to identify

the type and also to prevent the wrong type from being inserted into the DIMM slot

on the motherboard. You must ask your retailer the correct DIMM type before pur-

chasing. This motherboard supports four clock signals.

System Memory

2. H/W SETUP

A7V-VM User’s Manual 9

2. HARDWARE SETUP

CPU

2. H/W SETUP

A7V-VM Socket A

A7V-VM

AMD™Athlon

NOTCH

LOCK

LEVER

BLANK

1. Locate the Socket 462 and open it by pulling

thelever gentlysideways away from the socket.

Then lift the lever upwards. The socket lever

must be fully opened (90 to 100 degrees).

2. Insert the CPU with the correct orientation.The

notched corner of the CPU must be oriented

toward the inner corner of the socket base

nearest to the lever hinge.

CAUTION! The CPU fits in one orientation

and should drop easily into place. Do not force

the CPU into the socket to avoid bending the

pins. If the CPU does not fit, check its

alignment and look for bent pins.

3. Once completely inserted, press the CPU firmly and close the socket lever until it

snaps into its locked position.

4. Place the CPU fan and heatsink on the CPU. The heatsink should entirely cover

the CPU. Carefully attach the heatsink locking brace to the plastic clips on the

socket base. With the added weight of the CPU fan and heatsink locking brace,

no extra force is required to keep the CPU in place.

CAUTION! Take care not to scrape the motherboard surface when mounting a

clamp-style processor fan, or else damage may occur. When mounting a heatsink

onto your CPU, make sure that exposed CPU capacitors do not touch the

heatsink, or else damage may occur! Refer to heatsink/CPU documentation.

NOTE! Do not forget to set the correct Bus Frequency and Multiple (available

only on unlocked processors) to avoid start-up problems.

2.5 Central Processing Unit (CPU)

The motherboard provides a Socket 462 or SocketAfor CPU installation.Afan and

heatsink should be attached to the CPU to prevent overheating. Purchase and install

a fan and heatsink before turning on the system.

10 A7V-VM User’s Manual

2. HARDWARE SETUP

2.6 Expansion Cards

WARNING!Unplug your power supply when adding or removing expansion

cards or other system components. Failure to do so may cause severe damage to

both your motherboard and expansion cards.

2.6.1 PCI Expansion Card Installation Procedure

1. Read the documentation for your expansion card and make any necessary hard-

ware or software settings for your expansion card, such as jumpers.

2. Remove your computer system’s cover and the bracket plate on the slot you

intend to use. Keep the bracket for possible future use.

3. Carefully align the card’s connectors and press firmly.

4. Secure the card on the slot with the screw you removed above.

5. Replace the computer system’s cover.

6. Set up the BIOS if necessary

7. Install the necessary software drivers for your expansion card.

2.6.2 Assigning IRQs for Expansion Cards

Some expansion cards need an IRQ to operate. Generally, an IRQ must be exclu-

sively assigned to one use. In a standard design, there are 16 IRQs available but

most of them are already in use, leaving 6 IRQs free for expansion cards. If your

motherboard has PCI audio onboard, an additional IRQ will be used. If your moth-

erboard also has MIDI enabled, another IRQ will be used, leaving 4 IRQs free.

Expansion Cards

2. H/W SETUP

Andere Handbücher für A7V-VM

Inhaltsverzeichnis

Andere Asus Hauptplatine Handbücher

Asus

Asus Pro H410M-C Bedienungsanleitung

Asus

Asus P5B Deluxe WiFi-AP Bedienungsanleitung

Asus

Asus P5RD2-VM Bedienungsanleitung

Asus

Asus Rog Maximus X Apex Bedienungsanleitung

Asus

Asus K8V Bedienungsanleitung

Asus

Asus P5GD2 PREMIUM Bedienungsanleitung

Asus

Asus F1A75-I DELUXE Bedienungsanleitung

Asus

Asus P4B-LA Bedienungsanleitung

Asus

Asus P8H61 PLUS R2.0 Bedienungsanleitung

Asus

Asus P4GPL-X Bedienungsanleitung

Asus

Asus P5KPL-AM - SE Motherboard And Intel Core 2... Bedienungsanleitung

Asus

Asus H87M-E Bedienungsanleitung

Asus

Asus M2N68-AM PLUS ION SI Bedienungsanleitung

Asus

Asus ROG STRIX TRX40-E GAMING Bedienungsanleitung

Asus

Asus F2A85-V PRO Bedienungsanleitung

Asus

Asus PRIME B650M-A WIFI Bedienungsanleitung

Asus

Asus H61M-G Bedienungsanleitung

Asus

Asus P9X79 Bedienungsanleitung

Asus

Asus MAXIMUS III FORMULA Bedienungsanleitung

Asus

Asus PRIME B650M-A WIFI Bedienungsanleitung

Asus

Asus TUF Z270 MARK 2 Bedienungsanleitung

Asus

Asus M3A78-CM - Motherboard - Micro ATX Bedienungsanleitung

Asus

Asus H87I-PLUS Bedienungsanleitung

Asus

Asus STRIX Z270E GAMING Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung

Epson

Epson S5U13700P00C000 Bedienungsanleitung

Gigabyte

Gigabyte GA-K8N Ultra-SLI Bedienungsanleitung

Albatron

Albatron PX925XE Series Bedienungsanleitung

Medion

Medion MS-7091 Bedienungsanleitung