Asus CUW-AM Bedienungsanleitung
CUW-AM User’s Manual 1
1. FEATURES
Specifications
1. FEATURES
1.1 The CUW-AM
The CUW-AM motherboard is carefully designed for the demanding PC user who
wants advanced features processed by the fastest processors.
1.1.1 Specifications
•Latest Intel Socket 370 Processor Support
Intel Pentium
®
III 100MHz FSB Coppermine core FC-PGA
Intel Celeron™ 66MHz FSB Mendocino core PPGA
•Latest Intel 810 Chipset! The 810 (GMCH+ICH) supports 66/100MHz FSB
and UltraDMA/66.
•IntegratedGraphics!Controller supports 3D hyper pipelined architecture, par-
allel data processing and compression, precise pixel interpolation, full 2D hard-
ware acceleration, and motion video acceleration.
•Custom Graphics Driver! You can gain about 12% performance over that of
the standard graphics driver (2D highend graphics WinMark) using the custom
graphics driver. The custom graphics driver also provides more features and
provides selection of higher refresh rates and resolutions.
•Versatile Memory Support! DRAM controller supports asymmetrical address-
ing and two DIMM sockets support Intel PC100-compliant SDRAMs (16, 32,
64, 128, or 256MB) up to 512MB. (supports a maximum of 4 sides)
• Latest Low Pin Count Multi-I/O: Provides two high-speed UART compatible
serial ports and one parallel port with EPP and ECP capabilities.
• Integrated IDE! Controller supports UltraDMA/66 up to 66MB/s, UltraDMA/
33 up to 33MB/s, and PIO Mode 4 up to 17MB/s.
•Firmware Hub! Provides security and other latest power computing features.
•Enhanced ACPI & Anti-Boot Virus Protection! Programmable BIOS (Flash
EEPROM),offering enhancedACPIforWindows98compatibility,built-infirm-
ware-based virus protection, and autodetection of most devices for virtually au-
tomatic setup.
•Highest Audio Quality! AC’97 DAC/ADC (software audio) built into the au-
dio codec reduces noise to improve audio quality and performance for a SNR
(signal to noise ratio) of +90dB. These features greatly improve voice synthesis
and recognition. If more quality is required, an optional onboard Crystal PCI
audio improves audio quality beyond software audio.
E546
2CUW-AM User’s Manual
Specifications
1. FEATURES
1. FEATURES
1.1.2 Performance
•UltraPerformance! Onboard IDE Bus Master controller with two connectors
that support four IDE devices in two channels. Supports UltraDMA/66,
UltraDMA/33 (IDE DMA Mode 2), PIO Modes 3 & 4, and supports Enhanced
IDE devices, such as Tape Backup, CD-ROM, CD-R/RW, and LS-120 drives.
• Dual Speeds! CPU frequency can operate at either 66MHz or 100MHz while
system memory operates at 100MHz. This asynchronous design can optimize the
VGA performance under shared memory configuration.
• DoubleorQuadrupletheIDETransferSpeed!IDEtransfers using UltraDMA/
33 Bus Master IDE can handle rates up to 33MB/s and up to 66MB/s using
UltraDMA/66 technology. The best of all is that these new technology is com-
patible with existing ATA-2 IDE specifications so there is no need to upgrade
current IDE devices or cables.
•Concurrent PCI! Concurrent PCI allows multiple PCI transfers from PCI mas-
ter buses to memory to CPU.
• SDRAM Optimized Performance! ASUS smart series motherboards support
the new generation memory, Synchronous Dynamic Random Access Memory
(SDRAM), which increases the data transfer rate to 800MB/s max using PC100
SDRAM.
• ACPIReady!ACPI provides more Energy Saving Features for future operating
systems (OS) supporting OS Direct Power Management (OSPM) functionality.
With these features implemented in the OS, PCs can be ready around the clock,
yet satisfy all the energy saving standards. To fully utilize the benefits of ACPI,
an ACPI-supported OS such as Windows 98 must be used.
•Extreme Graphics! The integrated motion compensation allows for smooth
MPEG1 or MPEG2 video playback. Fast 3D graphics engine allows for an ex-
citing gameplay experience.
CUW-AM User’s Manual 3
1. FEATURES
Specifications
1. FEATURES
1.1.3 Intelligence
• Auto Fan Off: The system fans will power off automatically even in standby
mode. This function reduces both energy consumption and system noise, and is
an important feature in implementing silent PC systems.
• Dual Function Power Button: Pushing the power button for less than 4 sec-
onds when the system is in the working state places the system into one of two
states: sleep mode or soft-off mode, depending on the BIOS or OS setting. When
the power button is pressed for more than 4 seconds, the system enters the soft-
off mode regardless of the BIOS setting.
4CUW-AM User’s Manual
2. HARDWARE SETUP
2.1 CUW-AM Motherboard Layout
Motherboard Layout
2. H/W SETUP
SECONDARY IDEPRIMARY IDE
PANEL
WOL_CON
FLOPPY
01
DIMM Socket 2 (64/72-bit, 168-pin module)
DIMM Socket 1 (64/72-bit, 168-pin module)
Row
23
01
COM1
PARALLEL PORT
VGA
PS2KBMS
T: Mouse
B: Keyboard
PS_FAN
Intel 810
Graphics &
Memory
Controller
Hub (GMCH)
LCDTV
Intel I/O
Controller
Hub (ICH)
CUW-AM
PCI Slot 2
PCI Slot 1
PCI Slot 3
CR2032 3V
Lithium Cell
CMOS Power
ATXPWR
4Mbit
Firmware
Hub
(FWH)
GAME_AUDIO
Mic
In
Line
Out
Line
In
USB
T: Port 1
B: Port 2
SYS_FAN
CD_IN
COM2
AUX_IN
Audio
Codec
USBV1
Socket 370
Power
Controller
Clock
Generator
Super
I/O
CUW-AM User’s Manual 5
2. HARDWARE SETUP
Layout Contents
2. H/W SETUP
2.2 Layout Contents
Expansion Slots
1) DIMM1, DIMM2 p. 7 168-Pin DIMM Memory Support
2) Socket 370 p. 9 Central Processing Unit (CPU) Socket
3) PCI1, PCI2, PCI3 p.10 32-bit PCI Bus Expansion Slots
Connectors
1) PS2KBMS p.11 PS/2 Mouse Connector (6-pin female)
2) PS2KBMS p.11 PS/2 Keyboard Connector (6-pin female)
3) USB p.12 Universal Serial Bus Ports 1 & 2 (Two 4-pin female)
4) PRINTER p.12 Parallel Port Connector (25-pin female)
5) COM1 p.12 Serial Port COM1 Connector (9-pin male)
6) VGA p.13 Monitor (VGA) Output Connector (15-pin female)
7) GAME_AUDIO p.13 Game/MIDI Connector (15-pin female) (optional)
8) GAME_AUDIO p.13 Audio Port Connectors (Three 1/8”female) (optional)
9) PRIMARY/SECONDARYIDE p.14 Primary/Secondary IDE Connectors (Two 40-1pins)
10) FLOPPY p.14 Floppy Disk Drive Connector (34-1pins)
11) WOL_CON p.15 Wake-On-LAN Connector (3 pins)
12) COM2 p.15 Serial Port COM2 Header (10-1 pins)
13) CPU_FAN, PS_FAN p.16 CPU and Power Supply Fan Connectors (3 pins)
14) LCDTV p.16 TV Out Connector (Two 20-1 pins)
15) CD_IN, AUX_IN p.17 Internal Audio Connector (4-pins) (optional)
16) USBV1 p.17 USB Header (6-1 pins)
17) MLED (PANEL) p.18 System Message LED (2 pins)
18) KLOCK (PANEL) p.18 Keyboard Lock Switch Lead (2 pins)
19) EXSMI (PANEL) p.18 System Management Interrupt Switch Lead (2 pins)
20) SPEAKER (PANEL) p.18 System Warning Speaker Connector (4 pins)
21) PWR (PANEL) p.18 ATX Power / Soft-Off Switch Lead (2 pins)
22) HDLED (PANEL) p.18 IDE Activity LED (2 pins)
23) PLED (PANEL) p.19 System Power LED Lead (3-1 pins)
24) RESET (PANEL) p.19 Reset Switch Lead (2 pins)
25) ATXPWR p.20 ATX Power Supply Connector (20 pins)
6CUW-AM User’s Manual
2. HARDWARE SETUP
Motherboard Settings
2. H/W SETUP
2.3 Hardware Setup Procedure
Before using your computer, you must complete the following steps:
•Check Motherboard Settings
•Install Memory Modules
•Install the Central Processing Unit (CPU)
•Install Expansion Cards
•Connect Ribbon Cables, Panel Wires, and Power Supply
2.4 Motherboard Settings
WARNING! Computer motherboards and expansion cards contain very delicate
Integrated Circuit (IC) chips. To protect them against damage from static electric-
ity, you should follow some precautions whenever you work on your computer.
1. Unplug your computer when working on the inside.
2. Use a grounded wrist strap before handling computer components. If you do
nothave one, touch bothof your hands toa safely grounded objector to a metal
object, such as the power supply case.
3. Hold components by the edges and try not to touch the IC chips, leads or con-
nectors, or other components.
4. Placecomponents ona groundedantistatic pad or on the bag thatcame withthe
component whenever the components are separated from the system.
5. Ensure that the ATX power supply is switched off before you plug in or
remove the ATX power connector on the motherboard.
WARNING! Make sure that you unplug your power supply when adding or
removing system components. Failure to do so may cause severe damage to
your motherboard, peripherals, and/or components. The onboard LED when
lit acts as a reminder that the system is in suspend or soft-off mode and not
powered OFF.
CUW-AM User’s Manual 7
2. HARDWARE SETUP
System Memory
2. H/W SETUP
Install memory in any combination as follows:
Location 168-pin DIMM SDRAM Total Memory
DIMM1 Single-Sided/Double-Sided x1
(Rows 0&1) 16, 32, 64, 128MB, or 256MB
DIMM2 Single-Sided/Double-Sided x1
(Rows 2&3) 16, 32, 64, 128MB, or 256MB
Total System Memory (Max 512MB) =
2.5.1 General DIMM Notes
•ASUS motherboards support SPD (Serial Presence Detect) DIMMs. This is the
memory of choice for best performance vs. stability.
•SDRAM chips are generally thinner with higher pin density than EDO (Extended
Data Output) chips.
•Single-sided DIMMs come in 16, 32, 64,128MB; double-sided come in 32, 64,
128, 256MB.
2.5 System Memory (DIMM)
NOTE: No hardware or BIOS setup is required after adding or removing memory.
This motherboard uses only Dual Inline Memory Modules (DIMMs). Sockets are
available for 3.3Volt (power level) unbuffered Synchronous Dynamic Random Ac-
cess Memory (SDRAM) of 16, 32, 64, 128MB, or 256MB.
This chipset does not support ECC. However, ECC memory modules may still be
used, but the ECC function will not be available.
8CUW-AM User’s Manual
2. HARDWARE SETUP
2.5.2 DIMM Installation
Insert the module(s) as shown. Because the number of pins are different on either
side of the breaks, the module will only fit in the orientation shown. DIMM mod-
ules are longer and have different pin contact on each side and therefore have a
higher pin density. SIMMs have the same pin contact on both sides.
0 1
CUW-AM
CUW-AM 168-Pin DIMM Sockets
Lock
FRONT
20 Pins
60 Pins
88 Pins
TheDIMMs mustbe 3.3VUnbufferedforthis motherboard.To determinethe DIMM
type, check the notches on the DIMMs (see figure below).
168-Pin DIMM Notch Key Definitions (3.3V)
DRAM Key Position Voltage Key Position
Unbuffered
RFU
Buffered Reserved
3.3V
5.0V
The notches on the DIMM will shift between left, center, or right to identify the type
and also to prevent the wrong type from being inserted into the DIMM slot on the
motherboard.You must ask your retailer the correct DIMM type before purchasing.
This motherboard supports four clock signals per DIMM slot.
System Memory
2. H/W SETUP
CUW-AM User’s Manual 9
2. HARDWARE SETUP
CPU
2. H/W SETUP
2.6 Central Processing Unit (CPU)
The motherboard provides a ZIF Socket 370. The CPU that came with the mother-
board should have a fan attached to it to prevent overheating. If this is not the case,
then purchase a fan before you turn on your system.
WARNING!Be sure that there is sufficient air circulation across the processor’s
heatsink by regularly checking that your CPU fan is working.Without sufficient
circulation, the processor could overheat and damage both the processor and the
motherboard. You may install an auxiliary fan, if necessary.
To install a CPU, first turn off your system and remove its cover. Locate the ZIF
socket and open it by first pulling the lever sideways away from the socket then
upwards to a 90-degree angle. Insert the CPU with the correct orientation as shown.
The notched corner should point towards the end of the lever. Because the CPU has
a corner pin for two of the four corners, the CPU will only fit in the orientation as
shown. The picture is for reference only; you should have a CPU fan that covers the
face of the CPU. With the added weight of the CPU fan, no force is required to
insert the CPU. Once completely inserted, close the socket’s lever while holding
down the CPU.
CAUTION! Be careful not to scrape the motherboard when mounting a clamp-
style processor fan or else damage may occur to the motherboard.
0 1
CUW-AM
CUW-AM Socket 370
Socket 370 CPU
(Top) Socket 370 CPU
(Bottom)
Notch Celeron
Gold Arrow Coppermine
10 CUW-AM User’s Manual
2. HARDWARE SETUP
Expansion Cards
2. H/W SETUP
2.7 Expansion Cards
WARNING! Make sure that you unplug your power supply when adding or
removing expansion cards or other system components. Failure to do so may
cause severe damage to both your motherboard and expansion cards.
2.7.1 Expansion Card Installation Procedure
1. Read the documentation for your expansion card and make any necessary hard-
ware or software settings for your expansion card, such as jumpers or switches.
2. Remove your computer system’s cover and the bracket plate with screw on the
slot you intend to use. Keep the bracket for possible future use.
3. Carefully align the card’s connectors and press firmly.
4. Secure the card on the slot with the screw you removed above.
5. Replace the computer system’s cover.
6. Set up the BIOS if necessary.
7. Install the necessary software drivers for your expansion card.
Inhaltsverzeichnis
Andere Asus Hauptplatine Handbücher
Asus
Asus H370 MINING MASTER Bedienungsanleitung
Asus
Asus P5GD1 Pro Bedienungsanleitung
Asus
Asus P5P800-MX Bedienungsanleitung
Asus
Asus P6T DELUXE/OC PALM - Motherboard - ATX Bedienungsanleitung
Asus
Asus PRIME B250M-J Bedienungsanleitung
Asus
Asus AAEON GENE-APL6 Bedienungsanleitung
Asus
Asus H170 PRO GAMING Bedienungsanleitung
Asus
Asus P5N-MX - Motherboard - Micro ATX Bedienungsanleitung
Asus
Asus STRIX X99 Bedienungsanleitung
Asus
Asus TUF GAMING B660M-E D4 Bedienungsanleitung
Asus
Asus ROG STRIX B550-F GAMING (WI-FI) Bedienungsanleitung
Asus
Asus B150M-K D3 Bedienungsanleitung
Asus
Asus Blitz Formula Bedienungsanleitung
Asus
Asus PRIME X370-PRO Bedienungsanleitung
Asus
Asus P4S800-MX SE Bedienungsanleitung
Asus
Asus Trooper B85 Bedienungsanleitung
Asus
Asus P5GPL Bedienungsanleitung
Asus
Asus UPX-EDGE-TGL01 Bedienungsanleitung
Asus
Asus P5WD2-E Premium Kurzanleitung
Asus
Asus ProArt B760-CREATOR Bedienungsanleitung
Beliebte Hauptplatine Handbücher anderer Marken
Texas Instruments
Texas Instruments ADS8372EVM Bedienungsanleitung
Commell
Commell MS-C73 Bedienungsanleitung
IBT Technologies
IBT Technologies MB860 Bedienungsanleitung
Nvidia
Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung
Biostar
Biostar M7VIT Bravo Bedienungs- und Montageanleitung
Intel
Intel D33217CK Bedienungsanleitung
