AT&T MDC 9000 Bedienungsanleitung

AT&T

MDC 9000 Cordless

Business Telephone

Quick Reference

Contents

Handset Controls

Handset Display 2

Line Status Indicators 2

Base Controls 3

Base Connectors 4

Troubleshooting 5-6

MDC 9000 Compatibility 7-12

Personal Directory back cover

Remember to press the [On/Off] button to turn on your cordless

phone, before pressing any other button.

Help!

For more information, see the MDC 9000 Cordless Business

Telephone Installation booklet. If you need assistance, call the

AT&T Helpline at 1 800 628-2888.

AT&T 503-801-100 Issue 1 (May 1994)

Comcode 107169047

1994 AT&T

AT&T

Handset Controls

Headset On/Off

Button

Press to turn the

User

Instructions

headset on and off.

Provides reference

information for most

common cordless phone

features.

Antenna

Headset Jack

Insert adapter

cord when using

a headset.

Directory Card

Handset Display

Displays status of

lines and range.

For detailed descrip-

tion, see "Handset

Diplay" on page 2.

Press to transfer

a call to another

extension.

Extension Label

Outside Line/

Earpiece

Volume

Control Switch

Slide switch to adjust

volume of earpiece.

Two positions:

Normal

and

High.

Status

Press to turn on

display when

handset is off, or to

update display when

STAT

indicator

appears.

On/Off

Press to turn the

handset on.

appears in handset

display. To turn off,

press again. Turn on

to make or answer

a call, and turn off

to “hang up.”

Conf

(Conference)

Press to conference

in (add) another

party to your call.

(Behind cover)

Battery Charging

Contacts

Handset battery

charges through

these contacts.

Programmable/

Intercom/Drop

Buttons (6)

See “MDC 9000

Compatibility” on

page 7 for system

button assignments.

HoId

Press to put a call

on hold.

Feat

(Feature)

Press to enter

programming mode

or to use dial-code

features. Not used

on System 25,

System 75, System

85, or DEFINITY

system.

Trans

(Transfer)

Write the extension

number on this label

using a pencil or

ball-point pen only.

Handset Display

➀

➁

➂

Line Status Indicators See below.

➃

➄

P appears when in programming mode.

STAT appears when handset is out of range. Remains until

all line status indicators are updated.

MSG appears when message LED lights on base.

BATT indicates low battery voltage. Handset also emits 4

short beeps. Place handset on base to recharge.

RANGE indicates handset is out of range when [On/Off] or

[Status] (off only) is pressed. Handset also emits 2 beeps. To

make or receive calls, move handset closer to the base.

ON indicates handset has been turned on by pressing [On/Off] .

➅

➆

Line Status Indicators

There are six line status indicators. Each indicator corresponds

to a specific outside line/programmable/intercom/drop button.

The indicators show either a triangle of a rectangle, signifying

activity as follows:

PARTNER Systems

Arrow ( ▲ or ▼ ) indicates activity at YOUR extension.

Rectangle () indicates activity at ANOTHER extension.

All Other Systems:

Rectangle () indicates activity at YOUR extension.

Arrow ( ▲ or ▼ ) indicates activity at ANOTHER extension.

Base Controls

Handset Hook

Rotate for wall

mounting.

Battery Charging

Talk LED

Contacts

Lights when handset

The handset battery

is removed from base

charges through

and switched ON.

these contacts.

Antenna

Base Extension

Label

Ringer Volume

Controls

Write this phone's

extension number

on this label using a

pencil or ball-point

pen only.

Base Ringer

Rings when a call

comes in. Adjust

volume or turn ringer

off using the Ringer

Volume Controls.

Message LED

Press appropriate but-

ton to adjust base's

Charge LED

ringing volume. Base

ringer turns off at bot-

tom of range (unless

handset is on the base).

When the handset is on

the base, only the base

rings. When the hand-

set is off the base, both

base and handset ring.

Lights when handset

is placed properly on

base and battery is

charging.

Base Connectors

Power Cord

Channel

TeIephone Line

Cord Channel

Desk mounting only. Desk mounting only.

Power Cord

Mounting Stand

Slot

For attachment of the

mounting stand.

Channel

Power Cord

Jack

Power cord is

inserted here.

Wall mounting only.

Mounting Stand

Slot

Telephone Line

Cord Jack

Telephone line cord

is inserted here.

For attachment of

the mounting stand.

Troubleshooting

If you have a problem with your cordless phone, you may be

able to solve it by following the procedures listed here. If you

cannot resolve a problem using these procedures, call the

AT&T Helpline at 1 800 628-2888, 24 hours a day.

Symptom

Possible Causes Possible Causes

RANGE

indicator Handset is out of range of Move closer to the base.

appears on the

the base.

handset display.

STAT

indicator

Handset is too far from the Move closer to the base;

appears on the base for display to be or

handset display. updated automatically. Press

[Status]

to update

indicators on display.

BATT

indicator Battery pack power is low.

Recharge battery pack

appears on the by placing the handset on

handset display. the base.

Range for calls is

Something in the area may

Relocate base to see if

lower than expected. be interfering with your

the range improves (see

radio transmissions (for

“Positioning the Base" in

example, metal reinforced

the Installation booklet)

ceilings, brick walls; or

personal computers,

Turn off or unplug nearby

facsimile machines).

equipment (for example,

computer, modem) to see if

it is causing interference. If

it is, make sure it is on a

different power line or

relocate it further from the

base, if possible.

Headset use is limiting the Move closer to the base or

range. use the handset.

Background noise

Radio Frequency Move base to higher

occurs while on a call.

Interference.

location

Move base a few feet to the

side, front or back.

Battery pack goes

Power outage or base is Plug base into an outlet not

dead when handset unplugged. controlled by a switch.

is in base.

Troubleshooting

Symptom Possible Causes

Possible causes

No ring on incoming Handset is out of range of

Move closer to the base.

call, or handset

the base.

makes hissing

sounds.

Base antenna is not in

Rotate antenna on base

upright position. into upright position.

If you have more than one Place correct handset in

MDC 9000 phone, wrong

base for at least 10 seconds.

handset is placed in the

base.

System is programmed Reprogram extension so

so line does not ring at

the line rings (see system

extension.

documentation).

Base makes clicking There is an open connec- Check the wiring and

sounds.

tion between the base unit

modular connections.

and the connecting switch.

Charge LED does Battery contacts need to Rub battery contacts lightly

not light when hand-

be cleaned.

with a soft eraser. Be sure

set is in base. battery contacts on handset

touch contacts on base.

Base not powered. Plug base into an outlet not

controlled by a switch.

Charge LED flashes

No battery pack or defective Remove battery pack, then

when handset is in

battery pack in handset. reinsert it. If problem recurs,

base. replace battery pack.

Handset does not

Recent occurence of

Remove handset from base

respond to repeated

lightning or strong then replace for 10 seconds;

button presses. electrical interference.

Unplug base from AC

wall outlet for one minute,

plug back into outlet, and

place handset on base for

10 seconds;

Unplug line cord from

base for one minute, then

reconnect it;

Remove handset battery for

one minute, replace, then

place handset on base for

10 seconds.

MDC 9000 Compatibility

PARTNER® systems: the MLC-6 Cordless Telephone; the

MERLIN®, MERLIN plus, and MERLIN II systems: a

MERLIN LEGEND® systems: a 10-button ATL set.

System 25: a 10-button set.

System 75, System 85, and DEFINITY systems: a 7303s set.

Your cordless phone is compatible with the phone systems

listed below. To use your phone, follow the programming and

call handling instructions that come with your phone system,

or the specific phone identified below.

■MDC 9000 is fully compatible with the PARTNER

family of phone systems.

■

5-button phone.

■

Carefully note the functional differences between your cordless

phone and the one identified above, as described in the

foIlowing sections.

Entering Station Programming Mode

■ To enter programming mode, turn the handset on, then

press [Feat] followed by [0] [0] .

■ To exit programming mode, press [Feat] followed by [0] [0]

or turn the handset off.

NOTE:

The above instructions do not apply on System 25, System 75,

System 85, and DEFINITY systems. On those systems, program-

ing buttons are assigned by your system administrator.

PARTNER, MERLIN, MERLIN LEGEND and DEFINITY are registered trademarks

of AT&T

MDC 9000 Compatibility

Programming System Features

PARTNER Systems:

■ PARTNER II and PARTNER Plus system buttons should be

assigned as follows; 1, 2, 3, and 4 are line or feature buttons

(for a PARTNER system, buttons 1 through 4 are line only):

MERLIN Systems:

■

It is recommended that you use MERLIN 206/410/820

systems installed with Feature Package 2 with your

cordless phone.

You must disable the Voice Announce feature. This phone

does not have a speaker function.

You should not be assigned to a paging group.

To program the Ringing Option feature, use the “arrow” and

“rectangle” indicators in the display as the equivalent of red

and green LEDs, respectively.

For MERLIN II system users, if you program an Auto Intercom

button, idle line preference must be set to intercom.

If any of your incoming lines has the call waiting feature,

program the Recall feature on one of the programmable

buttons and press it before you pick up a waiting call. You

can dial #50 before you pick up a waiting call on the follow-

ing: MERLIN 206/410/820 systems only with Feature Package

2, and all MERLIN Plus, MERLIN II and MERLIN 1030/3070

systems. Pressing [On/Off] will disconnect the call.

MDC 9000 Compatibility

■ MERLIN 206/410/820 systems and MERLIN Plus system

buttons should be assigned as follows; 2, 3, 4, and 5 are

line or feature buttons:

■ To use MERLIN LEGEND feature codes with this phone,

program the top right-hand button as a System Feature

button. This will permit you to use the wide array of

LEGEND system features by turning the set on, pressing

the System Feature button, and dialing the appropriate

"*" code number. Your cordless phone’s [Feat] button only

allows you to enter programming mode. It does not work

when using the MERLIN LEGEND system features.

■ MERLIN 1030/3070, MERLIN II, and MERLIN LEGEND

system buttons should be assigned as follows; 3, 4, and

5 are line or feature buttons:

Andere Handbücher für MDC 9000

Inhaltsverzeichnis

Andere AT&T Schnurloses Telefon Handbücher

AT&T

AT&T TL92271 Bedienungsanleitung

AT&T

AT&T 900 MHz Bedienungsanleitung

AT&T

AT&T E5908 Bedienungsanleitung

AT&T

AT&T TL86103 Bedienungsanleitung

AT&T

AT&T E2901 Bedienungsanleitung

AT&T

AT&T E5937 Bedienungsanleitung

AT&T

AT&T E2912 Bedienungsanleitung

AT&T

AT&T CL81114 Bedienungsanleitung

AT&T

AT&T E580-2 Bedienungsanleitung

AT&T

AT&T E6012B Bedienungsanleitung

AT&T

AT&T SL81108 Bedienungsanleitung

AT&T

AT&T HS8240 Bedienungsanleitung

AT&T

AT&T TL96271 Bedienungsanleitung

AT&T

AT&T DLP73450 Bedienungsanleitung

AT&T

AT&T TL78108 Bedienungsanleitung

AT&T

AT&T 1145 Bedienungsanleitung

AT&T

AT&T SB67118 DECT 6.0 Bedienungsanleitung

AT&T

AT&T 1160 Bedienungsanleitung

AT&T

AT&T HS-8200 Bedienungsanleitung

AT&T

AT&T 9353 Bedienungsanleitung

AT&T

AT&T TL92328 Bedienungsanleitung

AT&T

AT&T 2230 Bedienungsanleitung

AT&T

AT&T CL82229 Bedienungsanleitung

AT&T

AT&T EL52100 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

Panasonic

Panasonic KX-TGP700 Bedienungsanleitung

GE 27930 Bedienungsanleitung

Radio Shack

Radio Shack 43-3557 Bedienungsanleitung