AT&T TL71108 Bedienungsanleitung

Quick start guide

TL71108/TL71208/TL71308

5.8 GHz cordless

telephone with caller ID/

call waiting

Installation preparation

Avoid placing the telephone base too close to:

• Communication devices such as: television sets, VCRs, or other cordless

telephones.

• Excessive heat sources.

• Noise sources such as a window with traffic outside, motors, microwave ovens,

refrigerators, or fluorescent lighting.

• Excessive dust sources such as a workshop or garage.

• Excessive moisture.

• Extremely low temperature.

• Mechanical vibration or shock such as on top of the washing machine or work

bench.

If you subscribe to high-speed Internet service (Digital Subscriber Line - DSL)

through your telephone lines, you must install a DSL filter between the

telephone base and the telephone wall jack (see page 2). The filter will prevent

noise and caller ID problems caused by DSL interference. Please contact your

DSL service provider for more information about DSL filters.

Your product may be shipped with a protective sticker covering the handset or

telephone base display - remove it before use.

For customer service or product information, visit our website at

www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial

1 (866) 288-4268.

WALL

DESK DESK

Telephone base installation

If you subscribe to high-speed Internet service (Digital Subscriber Line - DSL)

through your telephone lines, you must install a DSL filter between the

telephone base and the telephone wall jack. The filter will prevent noise

and caller ID problems caused by DSL interference. Please contact your DSL

service provider for more information about DSL filters.

Install the telephone base as shown below.

5. Plug the other end

of the telephone

line cord into a

telephone jack.

1. Plug the small

end of the larger

power adapter into

the power jack at

the bottom of the

telephone base.

3. Route cords

through slots.

4. Plug the large end

of the larger power

adapter into a power

outlet not controlled

by a wall switch.

Power

adapter

2. Plug one end of the

telephone line cord

into the telephone

jack at the bottom of

the telephone base.

DSL filter (not included),

required if you have DSL

high-speed Internet service.

Telephone

line cord

Battery installation & charging

Install the battery as shown below. After installing the battery, you can make

and receive short calls, but replace the handset in the telephone base or

additional charger when not in use. For optimal performance, charge the

handset battery for at least 16 hours before use. When fully charged, the

handset battery provides approximately five hours of talk time or three days

of standby time.

If the battery is depleted, it may take approximately four minutes to charge

the handset before it can resume screen display. The screen will continue to

display LOW BATTERY until the battery has charged for approximately one

hour.

THIS SIDE UP

WARNING:DO NOT BURN OR

PUNCTURE BATTERIES

MADE IN CHINA

Battery Pack

BT5633/BT6823

3.6V 550mAh Ni-MH

THIS SIDE UP

WARNING:DO NOT BURN OR

PUNCTURE BATTERIES

MADE IN CHINA

Battery Pack

BT5633/BT6823

3.6V 550mAh Ni-MH

THIS SIDE UP

WARNING:DO NOT BURN OR

PUNCTURE BATTERIES

MADE IN CHINA

Battery Pack

BT5633/BT6823

3.6V 550mAh Ni-MH

THIS SIDE UP

WARNING:DO NOT BURN OR

PUNCTURE BATTERIES

MADE IN CHINA

Battery Pack

BT5633/BT6823

3.6V 550mAh Ni-MH

Plug the battery

securely into the plug

inside the handset

battery compartment,

matching the color-

coded label.

Insert the supplied

battery with the label

THIS SIDE UP facing up

as indicated.

Align the cover flat

against the battery

compartment cover,

then slide it upwards

until it clicks into

place.

Step 3

Step 2

Step 1

Battery installation & charging

Charge the handset by placing the handset face

up in the telephone base or in the additional

charger. The CHARGE light will be on when

charging.

Step 4

IMPORTANT INFORMATION

Use only the battery supplied with this product. To order a replacement or spare battery (AT&T

model 27910, part number 89-0099-00-00) or equivalent, visit our website at

www.telephones.att.com, or call 1 (800) 222-3111. In Canada dial

1 (866) 288-4268.

IMPORTANT INFORMATION

Use only the power adapter supplied with this product. To order a replacement power adapter,

visit our website at www.telephones.att.com, or call

1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.

2. The power adapters are intended to be correctly oriented in a vertical or floor mount position.

The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-

table or cabinet outlet.

1. Plug the small end

of the smaller power

adapter into the jack

on the underside of the

charger, then route the

cord through the slot

as shown.

Charger installation

2. Plug the large end

of the smaller power

adapter into a power

outlet not controlled by a

wall switch.

CID

Press to display caller ID

information.

DIR

Press to display directory

entries.

PHONE/FLASH

Press to make or answer

a call.

During a call, press to

receive an incoming call if

call waiting is activated.

MUTE/REMOVE

During a call, press to

mute microphone.

While reviewing the caller

ID history, press to delete

an individual entry, or

press and hold to clear

the caller ID history. While

predialing, press to delete

digits.

SPEAKER

Press to turn on the

handset speakerphone.

Press again to resume

normal handset use.

MENU/SELECT

Press to enter the menu.

While in the menu, press to

select an item or save an

entry or setting.

OFF/CLEAR

During a call, press to hang

up.

While using menus, press

to cancel an operation,

back up to the previous

menu, or exit the menu

display.

REDIAL/PAUSE

Press to view redial

memory.

While entering numbers,

press and hold to insert a

dialing pause.

INT

Press to begin an intercom

conversation or to transfer

a call.

Quick reference guide

CHARGE

On when the handset is

charging in the telephone

base or charger.

VOLUME

Press on the side of the

handset to adjust listening

volume. Each press of

the button increases or

decreases the volume.

Press or to scroll up

or down while in menus.

While entering names or

numbers, press or to

move the cursor to the left

or right.

Handset

IN USE

On when handset is in

use, or when you are

registering a handset.

Flashes when another

telephone is in use

on the same line, or

you are deregistering

handset(s) from the

telephone base.

Flashes quickly when

there is an incoming

call.

•

VOICEMAIL

Flashes when you

have new voicemail.

Voicemail is offered by

your telephone service

provider.

Telephone base

HANDSET LOCATOR

Press to initiate beeping

to locate misplaced

handsets.

Feature menu Feature menu

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

Panasonic

Panasonic KX-TGP700 Bedienungsanleitung

GE 27930 Bedienungsanleitung

Radio Shack

Radio Shack 43-3557 Bedienungsanleitung