AT&T Trimline TR1909 Bedienungsanleitung

Quick start guide

TR1909

Trimline® telephone

with caller ID/call waiting

Getting started

Handset layout

MEMORY

Press to access phone

numbers stored in the

memory.

Listening volume

Adjust the handset listening

volume to LO,MED, or HI.PAUSE/REDIAL

When the handset is lifted, press

to redial the last number dialed.

When storing a number in the

memory or directory, press to

insert a 3-second pause in the

dialing sequence.

PROG

Press to store a phone number in

the memory.

M1, M2, M3

Press to dial a one-touch

number from the memory.

MUTE

Press and hold MUTE to silence

the microphone to prevent the

other party from hearing you,

but you will still be able to hear

the other party. Release MUTE

to return to the original two-

way conversation.

Switch hook

When held, the telephone is in

idle mode.

When released, the telephone is

ready to make a call.

OPTION

Press to display the setting

options.

While in the option menu, press

to save the selection and move

to the next feature.

FLASH

When there is a call waiting signal,

press FLASH to put the current

call on hold and connect to the

new call. Press FLASH again to

return to the original call. Also,

press FLASH to activate other

telephone company subscriber

services such as three-way calling.

IN USE

Flashes quickly when there is an

incoming call.

Flashes slowly when the

telephone line cord is not

plugged into a wall jack or

another telephone at the same

line is in use.

CALL LIST /

When the telephone is in idle

mode, press to display caller ID

information.

REMOVE

While viewing the call log,

press to delete entry currently

displayed, press and hold to

remove all entries.

CLEAR

Press to exit dialing, to exit storing

a number in memory, to exit the

call log, or to return to the idle

screen anytime without saving the

changes.

DISPLAY DIAL

Press to dial the number currently

displayed.

Getting started

Screen display messages

CALL# Call number in the call log.

NEW New (unreviewed) call.

REP Repeat call from the same number.

The telephone line cord is not plugged into a wall jack.

The telephone or another telephone on the same line

is in use.

•

The battery power is low.

Screen icons

Screen display messages

REMOVE ALL? Remove all call log entries.

END OF LIST You have reached the end of the call log

entries.

Pro Program a one-touch or two-touch memory.

LIFT RECEIVER A caller ID entry is ready to be dialed by

lifting the handset.

TOTAL XX NEW XX The total and new (unreviewed) calls in the

call log.

CALL#

NEW

REP 0110 : 03AM 12/01

800-222-3111

TOTAL 12 NEW 01

Getting started

Battery installation

Before using the telephone, you should install four good AA alkaline batteries

(not included) to provide memory backup and enable the use of some features.

The four AA batteries are required for caller ID features and the IN USE light to

work. If good batteries are not installed, the display only works when you lift

the handset.

If you unplug the telephone from the wall jack, or you lose telephone service

for over 10 minutes, and good batteries are not installed, the following

information is lost: call list, numbers stored in one- and two-touch memory,

redial list, and all settings in the feature menu. It is recommended that you

initially install new batteries and change the batteries soon after the low

battery icon appears.

Press on the tab to open the cover of the battery compartment.

Install four new AA batteries (not included) in the battery compartment

according to the label + and - engraved in the compartment.

Close the battery compartment cover. Make sure it clicks into place.

NOTES:

Do not mix old and new batteries and do not mix alkaline and standard

(carbon-zinc) batteries.

When the batteries are installed, the screen will show 12:00 and the clock

will begin to run. It will reset to the correct time when the first caller ID

data is received.

Always disconnect all telephone lines from the wall outlets before replacing

batteries.

Install new batteries every six months to maintain the call log and

telephone memory.

•

Press this

tab to

open.

Step 1 Step 2 Step 3

Getting started

Telephone installation

If you subscribe to high-speed Internet service (digital subscriber line - DSL)

through your telephone lines, you must install a DSL filter between the

telephone line cord and the telephone wall jack. The filter prevents noise and

caller ID problems caused by DSL interference. Please contact your DSL service

provider for more information about DSL filters. Install the telephone as shown

below.

Plug one end of the coiled

handset cord into the handset

jack on the left side of the

telephone base. Plug the other

end into the handset.

One end of the telephone line

cord has been plugged into the

telephone jack on the bottom

of the telephone base. Double

check that it is plugged in firmly.

Thread the cord through the

channel and out of the mounting

area as shown.

Plug the other end of the

telephone line cord into a

telephone wall jack.

Put the handset on the

telephone base.

DSL filter

(not included)

Getting started

Installation options

Wall installation

To install the telephone base in the wall mount position, make sure that you

first unplug all cords connected to the telephone base.

Lift the handset and place it aside. On the telephone base, pull out the

handset tab and rotate it 180 degrees. Replace the handset tab back to the

grooves until it clicks into position.

Your telephone base is ready for tabletop use. If you want to mount your

telephone on a wall, use the provided wall mount bracket to connect with

a standard dual-stud telephone wall mounting plate. If you do not have this

mounting plate, you can purchase one from many hardware or consumer

electronic retailers. You might need a professional to install the mounting

plate.

3. Rotate the bracket to the wall

installation position, push the

bracket upwards as shown below

until it clicks into place.

2. Remove the bracket from the

base, hold the telephone base

with both hands, slide the

bracket upwards as the arrows

indicate.

Getting started

4. Route the telephone line cord through

the slot as shown below and plug the

other end of the telephone line cord

into a telephone wall jack. To mount

the telephone on the wall, position

the mounting holes A and B over

the telephone outlet mounting studs.

Slide the bracket down firmly so the

telephone is held securely on the

telephone outlet mounting studs.

5. Place the handset back on the

telephone base.

Installation options

Tabletop installation

To return the bracket from the wall installation to tabletop use, follow the

instructions below.

2. Lift the handset and place it aside. On the telephone base, pull out the

handset tab and rotate it 180 degrees. Replace the handset tab back to the

grooves until it clicks into position.

1. Remove the telephone base from the wall mounting plate. Unplug the

telephone line cord from the telephone wall jack and remove the cord from

the slots under the telephone base.

DSL filter

(not included)

Getting started

Installation options

3. Remove the bracket from the base,

hold the telephone base firmly,

slide the bracket downwards as the

arrows indicate.

4. Rotate the bracket to the tabletop

installation position, push the

bracket down as shown below

until it clicks into place.

5. Route the telephone line cord through

the slot as shown below. Plug the

other end of the telephone line cord

into the telephone wall jack.

6. Place the handset back on

the telephone base.

www.telephones.att.com

AT&T and the AT&T logo are trademarks of AT&T Intellectual Property II, L.P. d/b/a

AT&T Intellectual Property licensed to Advanced American Telephones, San Antonio, TX 78219.

Trimline® is a registered trademark of Advanced American Telephones.

Printed in China. Issue 4 AT&T 3/09

Andere Handbücher für Trimline TR1909

Inhaltsverzeichnis

Andere AT&T Telefon Handbücher

AT&T

AT&T DEFINITY 8101 Bedienungsanleitung

AT&T

AT&T CL2909 Bedienungsanleitung

AT&T

AT&T Partner MLS 12D Bedienungsanleitung

AT&T

AT&T CL81211 Bedienungsanleitung

AT&T

AT&T MS2085 Bedienungsanleitung

AT&T

AT&T BELL 2563HB Bedienungsanleitung

AT&T

AT&T Trimline TR1909 Bedienungsanleitung

AT&T

AT&T CL84250 Bedienungsanleitung

AT&T

AT&T Merlin Bedienungsanleitung

AT&T

AT&T Private Pay Phone Bedienungsanleitung

AT&T

AT&T E5865 Bedienungsanleitung

AT&T

AT&T PARTNER CIB 3169 Bedienungsanleitung

AT&T

AT&T Partner 34D Bedienungsanleitung

AT&T

AT&T Merlin Legend MLX-10D Bedienungsanleitung

AT&T

AT&T CL84109 Bedienungsanleitung

AT&T

AT&T CL2939 Bedienungsanleitung

AT&T

AT&T Partner MLS 34D Bedienungsanleitung

AT&T

AT&T CL4939 Bedienungsanleitung

AT&T

AT&T 831 Series Bedienungsanleitung

AT&T

AT&T ML17929 Bedienungsanleitung

AT&T

AT&T 1450 Bedienungsanleitung

AT&T

AT&T CL84100 Bedienungsanleitung

AT&T

AT&T CL84107 Bedienungsanleitung

AT&T

AT&T Merlin Bedienungsanleitung

Beliebte Telefon Handbücher anderer Marken

GE 2-9480 Bedienungsanleitung

Geemarc

Geemarc PHOTOPHONE 155 Bedienungsanleitung

Interquartz

Interquartz Gemini IQ333 Bedienungsanleitung

SSS Siedle

SSS Siedle HT 840-0 Bedienungsanleitung

Motorola

Motorola TITANIUM Bedienungsanleitung

Panasonic

Panasonic ICX Bedienungsanleitung

LG H870DS Bedienungsanleitung

Samsung

Samsung GT-I9500 Bedienungsanleitung

Selta

Selta zenyth 600 Bedienungsanleitung

Doro

Doro AFTI 20 Bedienungsanleitung

UNIQCELL

UNIQCELL A1 Bedienungsanleitung

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Bedienungsanleitung

BT Decor 425 Bedienungsanleitung

NEC

NEC SV8500 Bedienungsanleitung

Teledex

Teledex PEARL Bedienungsanleitung

Ericsson

Ericsson Dialog 3213 Bedienungsanleitung

Yealink

Yealink VP530 Bedienungsanleitung

Axess Telecom

Axess Telecom ACW-1xP800 Bedienungsanleitung