•An extension cord should not be used unless absolutely necessary. Use
of an improper extension cord could result in the risk of fire, electric
shock or electrocution.
• Do not operate charger if it has received a sharp blow, been dropped
or otherwise damaged in any way. Have it checked by an electrician or
power tool repairer.
• Do not disassemble charger. Take it to an electrician or power tool
repairer when service or repair is required. Incorrect reassembling may
result in a risk of electric shock, electrocution or fire.
•To reduce risk of electric shock, unplug charger from the outlet before
attempting any cleaning. Removing the battery pack will not reduce
this risk.
• Never attempt to connect 2 chargers together.
• DO NOT store or use the tool and battery pack in locations where the
temperature may reach or exceed 40ºC (such as outside sheds or metal
buildings in summer).
•The charger is designed to operate on standard household electrical
power (120 Volts). Do not attempt to use it on any other voltage!
The battery pack is not fully charged out of the carton. First read the
safety instructions and then follow the charging notes and procedures.
•The longest life and best performance can be obtained if the battery
pack is charged when the air temperature is between 18 - 24ºC. Do not
charge the battery pack in an air temperature below 10o C or above
40ºC. This is important and will prevent damage to the battery pack.
• Do not incinerate the battery pack even if it is seriously damaged or is
completely worn out. The battery can explode in a fire.
• Never attempt to open the battery pack for any reason. If the plastic
housing of the battery pack breaks or cracks, immediately discontinue
use and do not recharge.
This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety.
Charging the Battery
This tool has been shipped in a low charge condition
and should be fully charged prior to use.
Plug the 120V charger adaptor (12) into an appropriate
AC power outlet and switch on.
Connect the charger plug (11) of the AC adaptor into
the charging socket (7) of the screwdriver.
The red charge indication LED (6) will illuminate.
The batteries will take 3-5 hours to charge. This may vary up to 7 hours due
to the level of charge left in the batteries and also the ambient temperature.
NOTE: The charge indicator LED (6) will always be illuminated when the
charger is plugged in and turned on!
Initial Charge
Charge your battery for 5-7 hours then use it until it runs down and only
slowly operates. Recharge for 5-7 hours again.
Once again run your tool until only a small amount of charge remains.
Repeat the above cycle about 4 or 5 times, this should set the battery
“memory”, then charge as earlier stated.
Caution: This charger does not automatically turn off when the battery is
fully charged. Please take care not to leave the tool on the charger turned
on for excessive periods of time.
Switch off the charger at mains when charging is complete.
NOTE: The charge indicator LED (6) will be illuminated when the charger is
plugged in charging the screwdriver. The charge indicator LED (6) will turn
off when the screwdriver is fully charged.
Inserting Driver Bits
Important! Always unplug the charger and make sure
the forward/reverse lever (5) is in the lock position. Refer
to Forward / Reverse Lever in the coming instructions.
The screwdriver has a quick connect chuck (1) feature,
simply slide the collar of the quick connect chuck (1)
back towards the torque collar (2) to either insert or extract the driver bits
you are using. Release the collar once you have inserted the driver bit
to lock in your bit.
Replacement Driver Bits can be purchased at any tool store.
Always ensure that you only use single ended 2 .
For driver bits shorter than 50mm, it must be used with bits holder which is
also included in this kit. Otherwise, shorter driver bits may become stuck or
hard to remove from the screwdriver.
On/Off Switch
Depress the On/Off trigger (8) to start the screwdriver and keep holding it
for continuous operation.
To stop the screwdriver, release the On/Off trigger (8).
Note: This screwdriver does not have variable speed!
Additional Safety Instructions For Chargers
And Batteries (cont.)
Operation
Forward / Reverse Lever
To select the forward or reverse on your screwdriver
simply push the forward/ reverse slide lever (5) to the
left side for reverse (R) or the right side for forward (F).
To lock the screwdriver simply ensure that the
forward/reverse lever (5) is placed in between forward
or reverse position.
Torque Settings
When using your screwdriver for various driving applications, it becomes
necessary to increase and decrease the power and torque in order to
prevent the possibility of damaging screw heads, threads, work piece, etc.
In general, power and torque should correspond to the size of the screw
and the material type that the screw is being driven into.
To Adjust Torque
• Locate the arrow on the front of torque collar (2).
• Identify the drill bit icon or non torque setting and
6 torque settings on the front of the drill.
• Rotate the torque collar (2) to the desired setting
aligning the number on the front of the screwdriver
with the arrow torque collar (2).
•To increase or decrease torque, rotate torque
collar (2). The lower the number, the lower the torque or twisting action
the screwdriver will produce. The higher the number, the higher the
torque or twisting action the screwdriver will produce.
Always check that the correct torque setting is selected by practicing on
scrap material prior to carrying out a job.
Pre Drilling your Material
It is recommended to pre drill holes in the material you are about to screw
into. Pre drilling holes will assist the screwdriver when driving screws and
enable your tool to operate efficiently.
Operation Of The Screwdriver
Only use driver/drill bits which can be securely fastened in the quick
connect chuck (1) and for which the bits have been designed.
Before using the screwdriver check whether the screw-bit is inserted cor-
rectly. Avoid over-tightening screws, otherwise the screw head may be
damaged or stripping of the threads may occur.
Screw Insertion
Set the direction of rotation of the screwdriver to the clockwise/forward
direction using the forward/reverse lever (5). Insert the required driver bit
into the head of the screw. Hold the driver bit in line with the head of the
screw, otherwise the screw or the screw head may be damaged. Always
keep constant pressure while driving in the screw to avoid damage to the
driver bit or screw head.
Depress the On/Off switch (8) to start driving the screw into your workpiece.
Always hold the screwdriver firmly and when the screw is completely
screwed in, release the On/Off switch (8), otherwise the screw or the screw
head may be damaged. If the On/Off switch (8) is not released immediately
the high torque could also damage the driver bit or the screwdriver.
Screw Removal
Set the direction of rotation of the screwdriver to the anticlockwise/reverse
direction using the forward/reverse lever (5). Insert the required driver bit
into the head of the screw. Hold the driver bit in line with the head of the
screw, otherwise the screw or the screw head may be damaged.
Always keep constant pressure while driving or removing the screw to
avoid damage to the driver bit or screw head.
Depress the On/Off switch (8) to start removing the screw from your workpiece.
Always hold the screwdriver firmly and when the screw is completely
removed, release the On/Off switch (8).
Rotating Rear Handle
This screwdriver has two different handle configurations to assist with your
job requirements. Inline will assist you in hard to reach areas where
additional reach is required. Bent or “L” shape will provide you with
additional grip for those jobs where more torque is required.
To return the handle to the original position press the rotating handle lock
button (4) and rotate the handle clockwise till the handle locks into position.
,,
