ATEQ F6 Profinet Series Bedienungsanleitung

F6 Series – Profinet

Manual

 
 
1 / 75 
 
FG_F6_PROFINET_EN_04 / 2020-06-17 
Table of Contents 
Safety advisory / Warranty 
Good practices and safety instructions..........................................................................................3 
Preamble 
Introduction .................................................................................................................................4 
Basic notions................................................................................................................................5 
Hardware installation 
Hardware configuration................................................................................................................7 
Cabling.........................................................................................................................................8 
Configuration of the ATEQ device (slave) 
Setup of the station name ............................................................................................................9 
Setup of the Profinet configuration mode................................................................................... 10 
Setup of the IP address...............................................................................................................11 
Configuration of the master 
Installation of the Profinet module .............................................................................................12 
Configuration files ...................................................................................................................... 13 
Selection of the master card.......................................................................................................14 
Setup of the station name .......................................................................................................... 15 
Setup of the IP address...............................................................................................................16 
Setup of the Profinet configuration modes..................................................................................18 
Functional description of an ATEQ device 
Introduction ...............................................................................................................................23 
Configuration .............................................................................................................................32 
Cycle .......................................................................................................................................... 61 
Results ....................................................................................................................................... 66 
 
 
 

FG_F6_PROFINET_EN_04 / 2020-06-17

2 / 75

ATEQ Manufacturer Plants –Measurement Solution, Global Leader

ATEQ

15, rue des Dames, Z.I.

78340 LES CLAYES-SOUS-BOIS

FRANCE

info@ateq.com

ateq.com

T.: +33 1 30 80 1020

F.: +33 1 30 54 1100

ATEQ K.K.

3 –41 ATEQ Building, Ikehata

Chiryu-city, Aichi-pref

JAPAN

info@ateq.co.jp

ateq.co.jp

T.: +81 566-84-4670

F.: +81 566-84-4680

ATEQ China

98 Jian Peng Lu

Shanghai

CHINA

shanghai@ateq.com.cn

ateq.com.cn

T.: +86 21 6763 9508

F.: +86 21 6763 9528

ATEQ SYSTEMS ANALYSIS TAIWAN CO.,

LTD.

NO. 3, LAN 223, San Jia Dong Street

40642, TAICHUNG

TAIWAN

ateqtaiwan@ateq.com.tw

ateq.com.tw

T.: +886 4 2437 5278

F.: +886 4 2437 3675

ATEQ CORP.

35980 Industrial Road Suite L

Livonia MI 48150

UNITED STATES

leaktest@atequsa.com

atequsa.com

T.: +1 734-838-3100

F.: +1 734-838-0644

We continuously work on improving our products. This is why inforamtion contained in this manual,

the device and the technical specifications may be modified without prior notification.

Pictures and figures in this manual are non contractual

3 / 75

FG_F6_PROFINET_EN_04 / 2020-06-17

Safety advisory / Warranty

GOOD PRACTICES AND SAFETY INSTRUCTIONS

Safety recommendations

If the device is supplied with 100 / 240 V AC, it is mandatory to connect it to the ground with a good

link to the ground, to protect against electric hazard or electrocution.

It is dangerous to change the status of the outputs.

They can control power actuators or other equipment (mechanical, pneumatic, hydraulic, electrical or

other) which can cause serious personal injury and damage to surrounding material.

For safety and quality measurement reasons, it is important, before powering on the device, to ensure

that it is air supplied with a minimum operating pressure (0.6 MPa ± 15%).

Recommendations for the test environment

Keep the test area as clean as possible.

Recommendations for operators

ATEQ recommends that the operators who use the devices have training and a level of qualification

that correspond to the job to perform.

General recommendations

—

Read the user manual before using the device.

—

All electrical connections to the device must be equipped with safety systems (fuses, circuit

breakers, etc.) adapted to the needs and in accordance with the applicable standards and rules.

—

To avoid electromagnetic interference, electrical connections to the device must be shorter than 2

meters.

—

Power supply plug must be grounded.

—

Disconnect the device from the mains before performing any maintenance work.

—

Shut off the compressed air supply when working on the pneumatic assembly.

—

Do not open a connected device.

—

Avoid splashing water on the device.

ATEQ is at your disposal for any information concerning the use of the device under maximum safety

conditions.

We draw your attention to the fact that ATEQ cannot be held responsible for any accident related to

a misuse of the measuring instrument, the workstation or non-compliance of the installation with

safety rules.

In addition, ATEQ declines any responsibility for the calibration or the fitting of their instruments that

is not done by ATEQ.

ATEQ also declines any responsibility for any modification (program, mechanical or electrical) of the

device done without their written consent.

FG_F6_PROFINET_EN_04 / 2020-06-17

4 / 75

Preamble

INTRODUCTION

This manual intends to help you for the configuration and the use of your ATEQ F6 device on the

Profinet network.

For more information on your ATEQ equipment, refer to the Quick Start Manual.

5 / 75

FG_F6_PROFINET_EN_04 / 2020-06-17

BASIC NOTIONS

The numerical values used in the ATEQ device are coded on a Long format.

ATEQ devices are configured in Little Endian format. It means that the Least Significant Byte is sent

first on the network.

Word

A word is a 16-bit data. It is coded with two bytes (8bits):

—

The first byte is the Least Significant Byte ( LSB )

—

The second byte is the Most Significant Byte ( MSB )

Example of a word:

Reminder: “h” indicates a hexadecimal code, “(d)” indicates a decimal code.

Long format (Signed Double word)

A Long format data is coded with two words (of 16 bits).

In the memory range of the ATEQ device or when they are transmitted, both words are coming in the

following order:

—

The first word is the least significant word

—

The second word is the most significant word

—

Example of a Long format:

Address value

All address values are treated with the Long format.

Example –address of the “millibar” unit in the Unit table (see Unit table):

FG_F6_PROFINET_EN_04 / 2020-06-17

6 / 75

Numerical value

All the numerical values are treated with the Long format with fixed comma (10-3).

Thus, their value is expressed in thousandths of unit. So, this value must be multiplied by 1000 to get

the value in units.

For example, a value of 207055 represents 207.055. So, any numerical value must be divided by 1000

to get the real value:

—

207.055 = 207055 ÷ 1000

Example –Pressure:

Negative numerical value

All the negative numerical values are treated with Signed long format with fixed comma (10-3).

Thus, they must be multiplied by 1000 to get the value in units.

Example –Leak value (signed long):

7 / 75

FG_F6_PROFINET_EN_04 / 2020-06-17

Hardware installation

HARDWARE CONFIGURATION

Connect your ATEQ equipment to the Profinet fieldbus using its Profinet connectors and compatible

cables.

Your device has a Profinet internal board and two Profinet connectors.

The Profinet internal board is located inside your device. Two versions are available:

—

COMX 100

—

COMX 51

You can see the version installed using your user interface (see Identification of the version of the

Profinet module).

Your device has two M12 D coded type connector - 4 pins female connector.

For more information on your ATEQ equipment, refer to the Quick Start Manual.

M12 D coded type connector - 4 pins female connector

Pin number

Signal

Ethernet Tx + (Transmit Data +)

Ethernet Rx + (Receive Data +)

Ethernet Tx - (Transmit Data -)

Ethernet Rx - (Receive Data -)

FG_F6_PROFINET_EN_04 / 2020-06-17

8 / 75

CABLING

M12 - RJ45 cable

Cable with male M12 D coded type connector and an RJ45 connector (4 or 8 pins)

Male M12 Pin

number

Wire color

Signal

RJ45 - 4 pins Pin

number

RJ45 - 8 pins Pin

number

White/orange

Ethernet Tx + (Transmit Data +)

White/green

Ethernet Rx + (Receive Data +)

Orange

Ethernet Tx - (Transmit Data -)

Green

Ethernet Rx - (Receive Data -)

9 / 75

FG_F6_PROFINET_EN_04 / 2020-06-17

Configuration of the ATEQ device

(slave)

Use this procedure to set the name and the configuration mode of your device.

This configuration can be done with the front panel of your ATEQ device or with the ATEQ Fieldbus

Configurator software.

SETUP OF THE STATION NAME

The station name must be the same on slave and master.

Use the prefix ateqf6 and a suffix number using three digits (eg. ateqf6001).

From the ATEQ device

From the MAIN MENU screen of your ATEQ

device:

➢CONFIGURATION

➢AUTOMATISM

➢FIELDBUS

➢ADDRESS

From the ATEQ Fieldbus Configurator software

Andere Handbücher für F6 Profinet Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ATEQ Prüfgeräte Handbücher

ATEQ

ATEQ F600 Bedienungsanleitung

ATEQ

ATEQ F670 Bedienungsanleitung

ATEQ

ATEQ F600HP Bedienungsanleitung

ATEQ

ATEQ VT Bedienungsanleitung

ATEQ

ATEQ F600 Bedienungsanleitung

ATEQ

ATEQ F600 Bedienungsanleitung

ATEQ

ATEQ AX6000 Bedienungsanleitung

ATEQ

ATEQ CDP60 Bedienungsanleitung

ATEQ

ATEQ Hydra Betriebsanleitung

ATEQ

ATEQ H6000 Bedienungsanleitung

ATEQ

ATEQ ADSE 550 Bedienungsanleitung

ATEQ

ATEQ VT47 Bedienungsanleitung

ATEQ

ATEQ TPMS Bedienungsanleitung

ATEQ

ATEQ VT TRUCK Bedienungsanleitung

ATEQ

ATEQ VT TRUCK 2.0 Bedienungsanleitung

ATEQ

ATEQ F6 Profinet Series Bedienungsanleitung

ATEQ

ATEQ F5200 Gebrauchsanweisung

ATEQ

ATEQ F670 Bedienungsanleitung

ATEQ

ATEQ G620 Bedienungsanleitung

ATEQ

ATEQ D6 Series Bedienungsanleitung

ATEQ

ATEQ D6 Series Bedienungsanleitung

ATEQ

ATEQ PRIMUS F Series Bedienungsanleitung

ATEQ

ATEQ WU47 Bedienungsanleitung

ATEQ

ATEQ VT66MB Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung