Atlantic Technology 3.1 HSB Bedienungsanleitung

Instruction Manual

3.1 HSB

High Performance

Front Channel Speaker Base

with powered H-PAS Subwoofer

3.1 HSB Speaker Base System with H-PAS

Model: 3.1 HSB

H-PAS SPEAKER BASE SYSTEM

Thank you for choosing Atlantic Technology products. Your new speaker is

precision-crafted to give you years of enjoyable, trouble-free service. This manual

covers the Atlantic Technology 3.1 HSB H-PAS Speaker Base system. It will show you

how to incorporate this speaker into your home theater setup.

The 3.1 HSB can be used with current and past sound formats from Dolby, DTS and

Auro.

Table of Contents

3 Important Safety information

5 Description

5 Placement

6 Connecting Your System

8 Recommended set up

9 Care of your Speaker

9 Trouble shooting guide

10 Speciﬁcations

11 Warranty

For Future Reference

Record the serial number and date of purchase for the speaker here.

The serial number is found on the back of the enclosure.

Serial Number Date of Purchase

be duplicated or reproduced by any means, whether physical, electronic or otherwise without prior written

consent from Atlantic Technology International, Corp.

Atlantic Technology and the Atlantic Technology logo are registered trademarks of Atlantic Technology

International, Corp.

Speciﬁcations are those in effect at the time of printing. As part of our ongoing program of continuous

product improvement, Atlantic Technology reserves the right to change speciﬁcations or appearance at any

time without notice or obligation to modify existing product.

Instruction Manual

Important Safety Information

This product was designed and manufactured to

meet strict quality and safety standards. There are,

however, some installation and operation precau-

tions which you should be particularly aware of.

1. Read Instructions. All the safety and operating

instructions should be read before the system

is operated.

2. Retain Instructions. The safety and operating

instructions should be retained for future

reference.

3. Heed Warnings. All warnings on the appli-

ances and in the operating instructions should

be adhered to.

4. Cleaning. Unplug the appliance from wall

outlet before cleaning. Do not use liquid

cleaners or aerosol cleaners. Use a damp

cloth for cleaning.

5. Attachments. Do not use attachments not

recommended by the product manufacturer

as they may cause hazards.

6. Water and Moisture. Do not use this appli-

ance near water: for example, near a bath

tub, washbowl, kitchen sink, or laundry tub,

in a wet basement, or near a swimming pool,

and the like.

7. Accessories. Do not place this appliance on an

unstable stand, bracket, or table. The product

may fall, causing serious injury to a child or

adult, and serious damage to the product.

8. Power Sources. This product should be

operated only from the type of power source

indicated on the marking labels. If you are not

sure of the type of power supply to your home,

consult your dealer or local power company.

9. Grounding or Polarization. This product may

be equipped with polarized alternating-current

line plugs (plugs having one blade wider than

the other). This plug will ﬁt into the power

outlet only one way. This is a safety feature.

If you are unable to insert the plug fully into

the outlet, try reversing the plug. If the plug

should still fail to ﬁt, contact your electrician

to replace your obsolete outlet. Do not defeat

the safety purpose of the polarized plug.

10. Power Cord Protection. Power-supply cord

should be routed so that it is not likely to be

walked on or pinched by items placed upon

or against it, paying particular attention to

cords at plugs, convenience receptacles, and

the point where they exit from the appliances.

11. Lightning. Unplug the product from the

wall outlet for added protection during a

lightning storm, or when it is left unattended

and unused for long periods of time. This

will prevent damage to the product due to

lightning and power-line surges.

12. Overloading. Do not overload wall outlets and

extension cords as this can result in a risk of

ﬁre or electric shock.

13. Object and Liquid Entry. Never push objects of

any kind into this product through openings,

as they may touch dangerous voltage points

or short out parts that could result in a ﬁre or

electric shock. Never spill liquid of any kind

on this product.

14. Servicing. Do not attempt to service this

product yourself, as opening or removing

covers may expose you to dangerous volt-

age or other hazards. Refer all servicing to

qualiﬁed service personnel.

15. Damage Requiring Service. Unplug this

product from wall outlets and refer servic-

ing to qualiﬁed service personnel under the

following conditions:

a. When the power supply cord or plug is

damaged.

b. If liquid has been spilled, or objects have

fallen into the product.

c. If the product has been exposed to rain

or water.

d. If the product does not operate normally

by following the operating instructions. Ad-

just only those controls that are covered by

the operating instructions, as an improper

adjustment of other controls may result in

damage and will often require extensive

work by a qualiﬁed technician to restore

the product to its normal operation.

e. If the product has been dropped or the

3.1 HSB Speaker Base System with H-PAS

4 Important Saftey Information (cond't)

cabinet has been damaged.

f. When the product exhibits a distinct

change in performance this indicates a need

for service.

16. Replacement Parts. When replacement parts

are required, be sure the service technician

has used replacement parts speciﬁed by the

manufacturer or that the parts have the same

characteristics as the original part. Unauthor-

ized substitutions may result in ﬁre, electric

shock or other hazards.

17. Safety Check. Upon completion of any service

or repairs to this product, ask the service

technician to perform safety checks to deter-

mine that the product is in proper operating

condition.

18. This product is not intended for use outdoors.

CAUTION: To prevent electric shock, match

wide blade of plug to wide slot, insert

fully.

CAUTION: No naked flame sources,

such as candles, should be placed on

the product.

PRODUCT DISPOSAL: Certain in-

ternational, national and/or local

laws and/or regulations may apply

regarding the disposal of this prod-

uct. For further detailed information,

please contact the retailer where you

purchased this product or the Atlantic Technology

Importer/Distributor in your country. A listing of

Atlantic Technology Importer/Distributors can be

found on the Atlantic Technology website www.

atlantictechnology.com or by contacting Atlantic

Technology at: 343 Vanderbilt Avenue, Norwood,

MA 02062, USA. Phone: 781.762.6300.

NOTE: This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference in a residential instal-

lation. This equipment generates, and can radiate

radio frequency energy, and, if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to radio

or television reception, which can be determined

by turning the equipment off and on, the user is

encouraged to try to correct the interference by one

or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment

and receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is con-

nected.

• Consult the dealer or an experienced technician

for help.

Unpacking the Speaker

Use care when unpacking the speaker.

Remember to save all packing materials

until you are certain that the speaker

has not suffered damage in shipment. If

you ﬁnd such damage, either visible or

internal, contact your dealer immediately.

We recommend you save the carton,

packing pieces and plastic bags that came

with your speaker. They may be useful if

you move or need to ship your speaker for

any reason.

Instruction Manual

Description

The 3.1 HSB Speaker Base is an integrated high-performance loudspeaker system con-

taining all three front channel speakers (LCR) and a powered subwoofer in a single

elegant, slim enclosure. Used in tandem with any A/V receiver and you have a spec-

tacular full featured home theater system. The subwoofer is powered by an internal 80

watt ampliﬁer that uses the SUB line level output from the A/V receiver. The subwoofer

also incorporates H-PAS technology to produce the lowest frequency response possible

from a cabinet this size, down to room shaking 35 Hz. The front channels require the

external ampliﬁers, found in all A/V receivers to power them. All this is wrapped up in a

4 3/4" tall cabinet designed to ﬁt directly under your ﬂat screen TV.

The 3.1HSB is designed for use with the latest generation of ﬂat screen video displays.

The advanced design of this speaker base delivers detailed, articulate sound for a dra-

matic viewing experience. Each of the three separate internal chambers contains a

complete speaker system. Each speaker system is comprised of two 3 ½-inch (89mm)

composite paper cone woofers, and an advanced 3/4-inch (19mm) ferroﬂuid-cooled,

damped soft-dome tweeter.

The drivers are mounted in an acoustically inert, heavily braced MDF enclosure that will

support a ﬂat screen display weighing up to 100lbs.

The 3.1 HSB Speaker Base is designed to support the weight of

today's ﬂat-panel video displays, in sizes up to 65 inches weighing up

to 100 lbs (45kg), and must be placed upon a ﬂat, level, and sturdy

surface, capable of safely supporting the total weight involved.

Cautions:

• The video display's stand or feet must rest fully within the ﬂat area of the top of the 3.1 HSB speaker base,

and not on its grille. This ﬂat area is 33 x 14 5/8" (838 x 372mm).

• As recommended by many display makers, we also strongly suggest that you tether the display to the wall,

especially if there are children in your home.

• Do not place objects between the speaker base and the surface it sits on - they could interfere with the

downward ﬁring woofer.

• This unit contains non-magnetic shielded speakers. Do not place magnetically sensitive items (hard disk

drive, CRT TVs, etc.) near the unit.

Placement

3.1 HSB Speaker Base System with H-PAS

6 Connecting Your System

U.S. Patent 8,094,855 B2. H-PAS is a trademark of AT Int’l Corp,

Tested to Comply with FCC Standards for Home or Office Use.

1234567

1. Standby/Status: Controls and indicates the

power and auto sensing circuit

2. DC IN: Input connector for power supply

3. Lowpass Control: Controls the internal low pass

ﬁlter

4. Bypass switch: Activates the Lowpass control

5. Phase switch: Controls the phase of the subwoofer

6. Level control: Controls the subwoofer output level.

(volume control)

7. Input: Subwoofer input (RCA connector)

8. Front Left, Center, Right Speaker Inputs

Connecting Your System

Follow the SYSTEM WIRING DIAGRAM to connect the 3.1HSB to your system.

SUBWOOFER: Use a quality RCA cable to connect from the SUB output on your A/V

receiver to the subwoofer INPUT (7) on the back of the 3.1 HSB.

FRONT CHANNEL SPEAKERS: Using high quality dual conductor stranded wire of

16 gauge or heavier, connect the speaker wires from the output terminals on the A/V

Receiver to the appropriate speaker input terminals on the back of the 3.1 HSB. The

lower the gauge number, the heavier the wire. Use heavier gauge wire for runs over 25'

(7.62m).

Remove ½ inch (6mm) of insulation from the end of each wire. Push down on the ter-

minal connector and an opening will appear in the connector that is capable of hold-

ing heavy gauge wire. Insert the bare wire into the opening and release the terminal. Be

sure to observe correct polarity, connecting the positive (+) leads to the red terminals and

Rear View

Instruction Manual

the negative (-) leads to the black terminals. Look carefully at the wires you are using and

note that one of the conductors of each pair will typically be identiﬁed by color print-

ing on the outer jacket, ridges on the outer jacket, or a thread intertwined with the wire

strands. By convention, the marked wire is connected to the red (+) terminal. Also be

sure that no stray strands of wire touch across any terminals.

WARNING: To prevent risk of electrical shock or damage to your equipment, always

switch off the ampliﬁer or receiver when making any system connections.

POWER SUPPLY:

A separate power supply and power supply cable have been

included with your system. After the audio connections have been made, connect the

cable from the power supply to the DC IN jack on the rear of the speaker base. Then

connect the power supply cable to the power supply and plug it into an active outlet.

NOTE:

The power supply provided is capable of operating from 100-240 volts 50-60Hz.

WARNING: Before turning on the A/V receiver, be certain that no stray wire strands are

touching across any terminals as this might damage it.

Finally, recheck the polarity of your front speakers by listening to some music with

good bass content. If the sound seems “hollow”, unusually spread out, or seem to

have weak bass, reinspect your connections for proper polarity and correct any out of

phase connections.

allrights reserved. Designedin USA. Made in CHINA.

U.S.Patent 8,094,855 B2. H-PASis a trademark of AT Int’l Corp,

Testedto Comply with FCC Standards for Home or Office Use.

RIGHT CENTER LEFT

LEFT

SURROUND

RIGHT

SURROUND

SUB OUT

optional surround speakers

POWER SUPPLY

A/V RECEIVER

(not included)

contact Atlantic Technology for recommondations

SYSTEM WIRING DIAGRAM

3.1 HSB Speaker Base System with H-PAS

RECOMMENDED SETUP

Use your A/V receiver to handle all the low and high-pass functions.

Set the 3.1 HSB's subwoofer amp settings as follows:

Standby: Auto

Lowpass Bypass

Phase: Normal

Level: 11 o'clock position

Refer to your A/V receiver's instructions to set its speaker conﬁguration as follows:

L, C, R, SR size: Small

L, C, R, SR Hi-pass: 125Hz

Subwoofer: ON

Subwoofer Low-pass 125 Hz

ALTERNATE SETUP

Should you wish to ﬁne-tune the subwoofer manually, begin with the above set-

tings, then:

• Change the A/V receiver's subwoofer lowpass frequency to its highest setting.

• Enable the 3.1 HSB's lowpass ﬁlter by moving its rear-panel switch to the

LOWPASS position.

• Adjust the Lowpass Frequency and Phase controls on the 3.1 HSB.

LOWPASS FREQUENCY

We recommend using an initial setting of 125Hz (around 2 o'clock) for the

3.1 HSB, and adjusting from that point. The goal is to obtain a smooth transition

between the subwoofer and the front channels, and produce a cohesive and well

integrated sound “picture.”

To do this, play something with a "walking bass line", where some of the bass

notes are played by the front channels, and some by the subwoofer. A good exam-

ple of this is Van Morrison's "Into the Mystic."

While listening, adjust the lowpass control to avoid excessive overlap (too-loud

notes) or acoustic gap (missing or weak notes) in the cross-over area.

In the end, a little time spent ﬁne-tuning will generally result in dramatically better

bass response.

PHASE CONTROL

This switch allows precise acoustic matching of the subwoofer with the front chan-

nels. Try in both positions, and use the position that results in the strongest bass

output, especially in the front channel-to-subwoofer cross-over area.

Instruction Manual

Care of Your Speaker

Clean your cabinet using a soft, lint-free cloth. If you wish, you can slightly moisten

the cloth with plain water. Do not use any other cleaning agents or chemicals. Be care-

ful not to get any water on the driver cones or tweeter domes. After carefully removing

the grille from the speaker, gently clean it with a very slightly damp, lint-free cloth.

To remove the grille; gently pull the grille straight forward from the cabinet starting

at both ends working towards the middle until it is fully free from the cabinet. Do not

use a tool or pick as this may cause damage.

Troubleshooting Guide

Once your speaker base is set up, you should have many years of maintenance free

enjoyment from your system. However, if you should encounter a problem, refer to

the following guide to help you ﬁnd the solution. If a problem persists, you should

contact your local authorized Atlantic Technology dealer.

Problem Possible Cause Possible Solution

No output from Left, Center or Right

channel

Input wire dislodged. Reconnect wire and move speaker base away

from wall.

No bass output Standby switch in the OFF position Move switch to either AUTO or ON position.

AC power cord unplugged or plugged

into a non-working outlet.

Plug into a working outlet.

Input cables not securely connected or

defective.

Check all connections, then try another

input cable.

No bass or weak bass output LEVEL control set too low. Turn LEVEL control up.

Audible buzz or hum Input cable not securely connected or

defective.

Check all connections, then try another

input cable.

Ground loop through antenna or cable

TV system input.

Test by disconnecting antenna and/or cable

system input leads. If hum goes away, install

isolation balun(s) at that point.

Trouble Shooting Guide

3.1 HSB Speaker Base System with H-PAS

Speciﬁcations

Front Channels

Woofers (6) Heavy-duty 3 1/2" (115mm) composite paper cone

Tweeters (3) 3/4" (19mm) soft dome, Ferroﬂuid cooled

Frequency Response 125Hz-20kHz

Nominal Impedance 6 Ohms per channel

Crossover frequency 3.75kHz, 2nd order

Sensitivity 89dB

Recommended

Ampliﬁer Power

10 - 150 Watts RMS per channel

Magnetic Shielding No

Powered Subwoofer

Subwoofer Down ﬁring 6 1/2" (165mm) long-throw composite paper cone

Ampliﬁer Power Internal; 80 Watts RMS <.2% distortion

Frequency Response 35 Hz - 220 Hz

Peak Output 106dB SPL

Input (1) RCA line level

Power Requirements 110-240V, 50/60Hz 2.5A (24VDC 4A Power Supply included)

Speciﬁcaons are those in eﬀect at the me of prinng. Atlanc Technology Internaonal, Corp. reserves the right to change

speciﬁcaons or designs at any me without noce and without obligaon to modify exisng units.

IMPORTANT NOTE:

The power recommendaon for this speaker assumes that you will not operate your ampliﬁer/receiver in a way that produces

distoron. Even rugged speakers like ours can be damaged by an ampliﬁer driven into audible distoron. The harsh ampliﬁer

distoron (“clipping”) that occurs in this situaon will eventually cause damage to the speaker system. This type of damage may

be cumulave and can build up over me, as the ampliﬁer is driven into overload again and again. Such damage is easily idenﬁ-

able through examinaon of the damaged speaker’s voice coil and is not covered by the warranty

Dimensions

(WxHxD)

35 3/4" x 4 3/4" x 16 3/4" (including grille)

910mm x 120mm x 426mm

Weight 29 lbs.

System

Inhaltsverzeichnis

Andere Atlantic Technology Sprecher Handbücher

Atlantic Technology

Atlantic Technology 6200C Bedienungsanleitung

Atlantic Technology

Atlantic Technology IW-115SR Bedienungsanleitung

Atlantic Technology

Atlantic Technology IW-155SR Bedienungsanleitung

Atlantic Technology

Atlantic Technology Gatecrasher 1 Bedienungsanleitung

Atlantic Technology

Atlantic Technology In-Ceiling Theater Systems ICTS-6.2 Betriebsanleitung

Atlantic Technology

Atlantic Technology 2200 C Bedienungsanleitung

Atlantic Technology

Atlantic Technology IWTS-14 SR Bedienungsanleitung

Atlantic Technology

Atlantic Technology 8200 System Bedienungsanleitung

Atlantic Technology

Atlantic Technology ICTS-6.3 Bedienungsanleitung

Atlantic Technology

Atlantic Technology IWTS-5 LCR Bedienungsanleitung

Atlantic Technology

Atlantic Technology 5 LCR Bedienungsanleitung

Atlantic Technology

Atlantic Technology IWTS-4LCR-IP Bedienungsanleitung

Atlantic Technology

Atlantic Technology Atlantic FS-4000 Bedienungsanleitung

Atlantic Technology

Atlantic Technology 44-DA Bedienungsanleitung

Atlantic Technology

Atlantic Technology ICTS-6.1 Bedienungsanleitung

Atlantic Technology

Atlantic Technology FS-252 Bedienungsanleitung

Atlantic Technology

Atlantic Technology AT-2 Bedienungsanleitung

Atlantic Technology

Atlantic Technology M110 Bedienungsanleitung

Atlantic Technology

Atlantic Technology AW-5 Bedienungsanleitung

Atlantic Technology

Atlantic Technology All Weather 100 Series Bedienungsanleitung

Atlantic Technology

Atlantic Technology 4400 LR Bedienungsanleitung

Atlantic Technology

Atlantic Technology IWTS-6 CMS Bedienungsanleitung

Atlantic Technology

Atlantic Technology 6200e Bedienungsanleitung

Atlantic Technology

Atlantic Technology FS-3200 C Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung