Atlantic SOLCC2 Bedienungsanleitung

1-877-80-PONDS
www.atlanticwatergardens.com 1-877-80-PONDS
www.atlanticwatergardens.com
Operating Manual
Color Changing
Lighting
Includes Models:
SOLCC2
SOLCC6
SOLCCLR
SOLCCMX3
SOLCCEXT

Introduction
Thank you for purchasing Color Changing SOL Lighting. Atlantic’s SOL
lighting features solid brass bodies with an oil-rubbed bronze finish. These LEDs
create a vibrant nightime atmosphere with 48 different colors and 16 different
pre-programed color changing combinations. Multiple LEDs can be connected to
be run through one transformer and be controlled by one remote.
Prior to Operation and Installation
Caution:
• DO NOT operate this product under any condition other than those for which it
is specified. Failure to observe these precautions can lead to electrical shock,
product failure, or other problems.
• Follow all aspects of electrical codes when installing SOL Lighting.
• To reduce the risk of electrical shock, connect only to a 110 volt receptacle
protected by a ground fault circuit interrupter (GFCI).
• The input power to the Color Changing Control Module is 12 volt AC. The
Control Module can be connected to a larger outdoor lighting transformer;
however this must be done on the 12 volt AC input side of Control Module.
Removing the Control Module or tampering with the cord between the Control
Module and the light fixture will damage the LEDs and void warranty.
• The Control Module is weather resistant with an IP54 rating. Do not submerse
the Control Module or expose it to heavy rainfall. It must be mounted off the
ground close to the power source. Failure to do so will void the warranty.
Installation
Fixture Installation
SOL Color Changing Spotlights offer three different mounting options for your
convenience:
• Adjustable stand: for placement on rock ledges, under waterfalls or for
highlighting streambeds
• Ground stake: for installation around the perimeter of the water feature or
in conventional landscape installations
• Nested: without the stand or stake, amongst the pond stones
SOL Color Changing Light Ring is ideal for illuminating fountains and up lighting
waterfalls.
• Proper light placement is important for every project. Whenever possible lights
should be positioned facing away from the viewing area to minimize hot spots.
2 7
Problem Possible Cause Possible Solution
Remote is not working
(no indicator light)
No batteries / batteries
dead Put in new batteries.
Remote is not working
(indicator light is on)
Remote is not synced with
Control Module
Refer to synchronizing the
remote instructions on page 5.
LED light will
not illuminate
No power to outlet Confirm power to outlet.
No Power to LED Check all connections, ensure
cord is not cut or damaged.
LED is broken / defective Replace LED bulb
LED color differs
from remote control
Improper connection
between LED light and
control module
Inspect connection / align
arrow on plugs
Controller failure Contact Dealer for repair /
replacement
Multiple lights display
different colors when
connected to the
same splitter
Improper connection
between LED light and
3-way splitter
Inspect connection / align
arrow on plugs
Controller failure Contact Dealer for repair /
replacement
Troubleshooting Guide
Always turn off power before inspecting the Color Changing Fountains. Failure to
observe this precaution can result in a serious accident.
Before ordering repairs, carefully read through this instruction booklet. If the
problem persists, contact your dealer.

4
Preset Light Changing Modes
5
AOn/Off Button
Touch for one second to turn on or off.
B
Mode Selection
Touch to switch between Color Wheel and Preset
Light Changing Mode
CColor Wheel
DPreset Light Changing Mode Selection (Forward)
EPreset Light Changing Mode Selection (Backward)
FBrightness / Speed (Up)
GBrightness / Speed (Down)
A
C
D
E
F
G
B
Indicator Lamp
1Solid Crystal White
2Continuous full spectrum fade change
3Solid Red
4Solid Green
5Solid Blue
6Solid Aqua
7Solid Purple
8Solid Yellow
9Red-Green-Blue jump change
10 7 color jump change
11 Red-Green-Blue dimmer change
12 7 color dimmer change
13 7 color dimmer then
7 color jump change
14 Flashing Red
15 Flashing Green
16 Flashing Blue
17 Flashing Red and Blue
Mode Selection
• To switch to the Color Wheel: hold the B button for three seconds or until the
light changes to Crystal White. Hold down the B button again, and the light will
return to the last color displayed while in the Color Wheel mode. Run your
finger around the color wheel to select a new color.
• To switch to the Preset Light Changing Modes: hold the B button for three seconds
or until the light changes to Crystal White. Press the D button, and the light will
return to the last preset mode displayed while in the Light Changing Modes. Press
the D and E button to switch between the different preset modes.
Changing the Brightness and Speed
In Modes 1-8 and 14-16, you can use the F and G keys to change the brightness of
the light. In Modes 9-13 and 17, you can use the F and G keys to change the speed
of the light transitions. There are 8 levels for each.
Synchronizing the Remote to the Control Unit
If the remote control stops working properly, please install fresh batteries. If
problems persist, the remote may need to be re-synced to the control module.
Follow the instructions below to re-sync the remote control.
1. Unplug the transformer .
2. Hold the F button down (The red indicator lamp on the remote will be blinking).
3. While still holding the F button down, plug in the transformer. The Colorfalls
will start blinking.
• If the light ring blinks three times and stops, the remote and control unit
are synchronized.
• If the light ring blinks six or more times, it is clearing all codes. Repeat
steps 1-3.
Maintenance
Replacement LED Bulbs are available for SOL Color Changing Spotlights and
Compact Spotlights. To loosen and tighten the brass lens ring on SOL Color
Changing Spotlights and Compact Spotlights, use the included key. Simply place
the key in the slots on the brass lens ring to loosen or tighten. Ensure that all
components are installed correctly after servicing. Inspect the silicone gaskets for
defects and proper placement before re-assembling. Ensure that the lens ring is
tightly secured before submersing the fixture.
Operation
Technical Data (Control Module)
Working Temperature:
0ºF -140ºF (-20°C - 60ºC)
Output: 3 circuits (R/G/B)
Remote Control Functions
Input Power: AC12V
Output Power: DC12V
Output Current: 5A /circuit
Brass Body
Disc Lamp Gasket Lens Slot
Brass Lens Ring
SOLCC2:

6
Warranty
All SOL Lighting carries a one-year limited warranty. This limited warranty is
extended solely to the original purchaser commencing from the date of the
original purchase receipt and is void if any of the following apply:
• The cord has been cut or altered between the light body and the Control
Module.
• The light body / LED components have been misused or abused.
• The light body / LED components have been disassembled or
modified other than as described in this manual.
• The Control Module and/or Remote Control have not been adequately
protected from moisture.
Brass Body
Brass Lens Ring
LED Bulb
Gasket Lens Slot
SOLCC6:
3
• When camouflaging the light cord with rocks and gravel, always leave enough
slack in the cord so that the fixture can be raised above water level for servicing.
• Always verify that the lens cover is tightly secured before submersing the fixture.
• Never cut or shorten the light cord between the Control Module and the light
fixture. Altering the Light Cord will damage the LEDs and void warranty.
• 6 wire extension cords (part # SOLCCEXT) are available to add an additional
20’ of cord to any SOL Color Changing Light. Only one cord can be used on
each light. Never connect multiple extension cords together.
SOLCCMX3 Control Module Installation
• The Control Module is weather resistant with an IP54 rating. Do not submerse
it or expose it to heavy rainfall. It must be mounted off the ground close to the
power source. Failure to do so will void the warranty.
• Ensure that all cable connections are secure.
• Install the control box in a well-ventilated area to ensure that the module
operates within its specified working temperature.
• Verify that the control module input voltage is 12 volt AC. We recommend that
you use the transformer provided with this unit.
• Do not connect the power before the cord connections are finished.
• Do not cut or alter the cord between the SOL Light and the Control Module.
• The remote control requires three (3) AAA batteries (not included).
Connecting the Lights
Follow the connecting chart below to connect all cables. The SOLCCMX3 Control
Module and 3-way splitter will accept any combination of Color Changing SOL Light
styles. If more lights are required, multiple splitters can be connected together to
create more outlet connections. A larger transformer (80 watts
maximum) is required if additional lights are installed.
SOLCCLR
Control ModuleTransformer 3-way
Splitter SOLCC2
SOLCC6
Andere Handbücher für SOLCC2
3
Dieses Handbuch passt für folgende Modelle
4
Inhaltsverzeichnis
Andere Atlantic Beleuchtungsausrüstung Handbücher
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung

Goobay
Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung












