Atlantis A-15600-PS Bedienungsanleitung

2525 Quicksilver Rd. McDonald, Pennsylvania 15057

724-695-2900 | [email protected] | www.atlantisllc.com

Atlantis Power Supply

Part Number: A-15600-PS

Overview

The Atlantis A-15600-PS Power Supply has been specifically designed to be the interface between a Keyence

Ultrasonic Clamp-On Flow Meter and a Walchem I6 or I9 controller or directly to various chemical metering

pumps. The board can also be used for various other sensors where 24VDC power is required. The selectable

Relay or Pulse output mode allows the device to operate as a flow switch or a pulse output flow meter. The 4-

20mA output of the sensor is also passed through to output terminals for easy connection to a controller or

pump.

Therearemainly twodifferent usecasesfortheA-15600-PS powersupply.Thefirstis directcontrolofachemical

metering pump by a Keyence flow meter. This method allows for a flow pacing analog signal and an on/off relay

signal to be transmitted from the Keyence flow meter through the power supply onto the pump. The second

use case connects the Keyence meter to a Walchem controller. The flow rate and totalizer values can be

monitored and recordedin the Walchem controller and if desiredtheWalchem controllercan be used to control

the speed and status of a pump.

A-15600-PS Atlantis Power Supply 
Instruction Manual 
 
 
Rev 0 Page 2 
Contents 
Overview .......................................................................................................................................................1 
Inputs & Outputs ...........................................................................................................................................3 
Use Case #1 –Keyence Flow Meter to Chemical Metering Pump...............................................................4 
Generic Non-Proportional Pump............................................................................................................5 
Walchem EWN Pump............................................................................................................................6 
Walchem IX Pump.................................................................................................................................7 
LMI A, B, and C Series Pumps..............................................................................................................8 
LMI AD Series Pumps............................................................................................................................9 
LMI AD 200 Series Pumps (Start/Stop Only) ......................................................................................10 
Use Case #2 –Keyence Flow Meter to Walchem Controller......................................................................11 
Keyence Analog Input to Walchem W600/900 or Intuition 6/9 Controller ...........................................11 
Keyence Pulse Input to Walchem W600/900 or Intuition 6/9 Controller..............................................11 
Keyence Pulse Input to Walchem Controller –Wiring Diagram..........................................................12 
Keyence Pulse Input to Walchem Controller –Keyence Settings.......................................................13 
Conclusion...................................................................................................................................................14 
 
 

A-15600-PS Atlantis Power Supply

Instruction Manual

Rev 0 Page 3

Inputs & Outputs

120V 15W Input Power

120V 5A Output Power

Fused 115V = Always On

N.O. 115V = Switched w/ NPN Input

4-20mA Output

Pulse Output

Dry Contact Output

Keyence Input

24+ / ( - ) = 24VDC 230mA Power

NPN = Sinking Digital Input

4-20+ = 4-20mA Analog Input

Output Type Jumper

Relay = R1 & R2 Activated

(NPN input wired to relay coils)

Pulse = R1 & R2 Bypassed

(NPN input wired directly to Pulse OUT)

A-15600-PS Atlantis Power Supply

Instruction Manual

Rev 0 Page 4

Use Case #1 –Keyence Flow Meter to Chemical Metering Pump

In this use case the A-15600-PS power supply can be configured with a variety of different output cables

depending on the pump being controlled. The next sections show the wiring diagrams for the standard

configurations and the part numbers corresponding to each setup. The programming instructions for the

Keyence flow meter are the same for all configurations shown for this use case. The Keyence settings are

as follows:

Keyence Flow Meter Settings

Initial Setup

1. Starting Screen shows P-n

2. Hold MODE + Up

3. Unit = G

4. P-n = nPn

5. Ch.2 = AnLG

6. dir = R

7. ¾ PiPe

8. End –Press MODE

Full Setup (After Initial Setup Hold MODE)

1. out 1 = Std

2. nonC = n.C.

3. AnLG = 4-20

4. A-Lo = 0.0

5. A-Hi = 𝑀𝑎𝑥 𝑃𝑜𝑙𝑦𝑚𝑒𝑟 𝐹𝑒𝑒𝑑 𝑅𝑎𝑡𝑒 (𝐺𝑃𝐻)∗100

𝐷𝑒𝑠𝑖𝑟𝑒𝑑 𝑆𝑜𝑙𝑢𝑡𝑖𝑜𝑛 %∗60

6. SPd = 5.0

7. ttL = 1

8. End –Use Arrows to Show FuLL –Press MODE

9. rESo = 0.1

10. AuE.d = 1

11. HYS = 0.3

12. cut = 0.5

13. Led = Grn

14. Eco = oFF

15. tESt = oFF

16. Loc = Std

17. dir = r

18. ¾ PiPe

19. AdJ = SEL

20. Sch = 80

21. End –Press MODE

*Bold shows values changed from Keyence default.

*A-Hi is set for 1% ratio by default.

To reset hold MODE and press Up 5x.

A-15600-PS Atlantis Power Supply

Instruction Manual

Rev 0 Page 5

Generic Non-Proportional Pump

This configuration does not control the speed of the pump in any way. The only controlled output is a

120V pigtail that can be used to provide the pump with the necessary power to run. The 120V output is

energized when the Keyence meter flow reading is higher than the switching setpoint set on the Keyence

meter’s front screen.

A-15600-PS Atlantis Power Supply

Instruction Manual

Rev 0 Page 6

Walchem EWN Pump

A-15600-PS Atlantis Power Supply

Instruction Manual

Rev 0 Page 7

Walchem IX Pump

A-15600-PS Atlantis Power Supply

Instruction Manual

Rev 0 Page 8

LMI A, B, and C Series Pumps

A-15600-PS Atlantis Power Supply

Instruction Manual

Rev 0 Page 9

LMI AD Series Pumps

A-15600-PS Atlantis Power Supply

Instruction Manual

Rev 0 Page 10

LMI AD 200 Series Pumps (Start/Stop Only)

Inhaltsverzeichnis

Andere Atlantis Stromversorgung Handbücher

Atlantis

Atlantis A03-PE702 Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung