Atlas Equipment Atlas TC221 Bedienungsanleitung

Inhaltsverzeichnis

Andere Atlas Equipment Reifenmontiermaschine Handbücher

Atlas Equipment

Atlas Equipment 200 Series Bedienungsanleitung

Atlas Equipment

Atlas Equipment TC589X Bedienungsanleitung

Beliebte Reifenmontiermaschine Handbücher anderer Marken

MW TOOLS

MW TOOLS BT200 Bedienungsanleitung

Hunter

Hunter Maverick Series Bedienungsanleitung

Corghi

Corghi BR2-C1E Bedienungsanleitung

Snap-On

Snap-On EEWH311B Bedienungsanleitung

TMG

TMG LC889NV Bedienungsanleitung

JMP

JMP Fix Moto Verdrahtungsschema

GIULIANO

GIULIANO S224 Technisches Dokument

Corghi

Corghi A 9222 HP TI Bedienungsanleitung

foc.us

foc.us F640 Bedienungsanleitung

Corghi

Corghi Artiglio Master 26 MI Bedienungsanleitung

SICE

SICE S 52A Bedienungsanleitung

Sealey

Sealey TC968.V2 Bedienungsanleitung

Coats

Coats 80C Bedienungsanleitung

HENNESSY INDUSTRIES

HENNESSY INDUSTRIES Coats Rim Clamp X-Model Series Bedienungsanleitung

Draper

Draper 78612 Bedienungsanleitung

Aston Global

Aston Global ATC-5800 Leitfaden

HENNESSY INDUSTRIES

HENNESSY INDUSTRIES Coats CHD-4730-4730W Handbuch

Butler

Butler NAV11N Bedienungsanleitung

This guide provides a basic understanding of the steps required to assemble the Atlas TC221

Tire Changer. Please read this guide and the Owner’s Manual carefully and completely before

assembling or operating your new tire changer.

STEP 1: Carefully remove the tire changer and included accessories from the plywood

container. Use the packing list or Owner’s Manual to verify that all parts are present:

STEP 2: Remove the six mounting bolts and washers from the top of the cabinet (shown

below). Set these bolts nearby. You will use the bolts again in the next step.

STEP 3: With an able bodied helper, carefully lift and position the main column as shown.

Install the six bolts removed in step 2. Tighten the bolts securely with a socket

wrench.

STEP 4: Remove the bead breaker pivot bolt and nut. Set them nearby. You will need them in

a later step. Install the round rubber pad onto the bead breaker shaft (arrow). Position

the bead breaker arm onto the chassis as shown.

STEP 5: Install the return spring as shown below.

STEP 6: Align the holes in the chassis and bead breaker arm. Install the pivot bolt and nut.

STEP 7: Guide the bead breaker shaft through the pivot pin (on the breaker arm). Install the

locknut using a socket wrench and extension. If an extension is not available to you,

you may pull the breaker shaft outward to access the shaft and nut with a wrench.

STEP 8: Use the locking handle to lock the hex shaft into place. Remove the bolt and cap from

the top of the hex shaft. Set the cap and bolt nearby.

STEP 9: Slide the coil spring over the hex shaft. Push the spring downward and install the cap

and bolt (removed in step 8) to hold the spring into place.

STEP 10: Install the stop bolt into the main column as shown.

STEP 11: Connect the 8mm coiled air line from the inflator gun to the elbow fitting on the rear

of the changer. This is a push-lock fitting. Press the hose completely into the fitting. It

will lock into place.

STEP 12: The assembly of your new TC221 tire changer is now complete. Double check your

work. Make sure there are no loose bolts, screws or connections. Refer to the

Owner’s Manual for operating instructions and safety warnings before using your

new tire changer.