Atlas PV-12PX Bedienungsanleitung

Model: PV12PX

Revised: 5/25/2021

CONTENTS

Product Features and Specifications .....................................................2

Installation Requirement ....................................................................3

Installation Steps ..............................................................................5

Exploded View .................................................................................27

Test Run .........................................................................................37

Operation Instruction ........................................................................38

Maintenance ....................................................................................39

Trouble Shooting ..............................................................................41

Lift Disposal ..................................................................................41

Warranty ……...................................................................................42

I. PRODUCT FEATURES AND SPECIFICATIONS

CLEAR-FLOOR DIRECT-DRIVE MODEL FEATURES

Model PV12PX (See Fig. 1)

· Direct-drive design, minimizes the lift wear parts and breakdown ratio

· Dual hydraulic cylinders, designed and fabricated to high standards, utilizing

imported oil seals in cylinder

· Self-lubricating UHMW Polyethylene sliders and bronze bush

· Single-point safety release with dual safety design

. Clear-floor design, provides unobstructed floor use

. Overhead safety shut-off device prevents vehicle damage

. Adjustable heights to accommodate varying ceiling heights

MODEL PV12PX SPECIFICATIONS

Arm Swings View

Fig. 2

Model

Lifting

Capacity

Lifting

Time

Lifting Height

Overall Height

Overall

Width

Minimum

Pad Height

Motor

PV12

12,000lbs

69S

72 ½”–81 ½”

174”/198”

150 ¾”

4 ½” –13 ½”

2.0 HP

II. INSTALLATION REQUIREMENT

A. TOOLS REQUIRED

✓Rotary Hammer Drill (Φ19)

✓Hammer

✓Level Bar

✓English Spanner (12")

✓Ratchet Spanner With Socket (28#)

Wrench set

✓Carpenter’s Chalk

✓Screw Sets

✓Tape Measure (7.5m)

✓Pliers

✓Socket Head Wrench (3#, 5#, 8#)

Lock Wrench

(10#, 13#, 14#, 15#, 17#, 19#, 24# ,27#, 30#,)

Fig. 3

B. Equipment storage and installation requirements.

The equipment should be stored or installed in a shady, normal temperature,

ventilated and dry place.

C. The equipment should be unloaded and transferred by forklift.

D. SPECIFICATIONS OF CONCRETE (See Fig. 5)

Specifications of concrete must be adhered to the specification as following.

Failure to do so may result in lift and/or vehicle falling.

1. Concrete must be thickness 6”minimum and without reinforcing steel bars, and

must be totally dry before lift installation.

2. Concrete must be in good condition and must be of test strength 3,000psi

(245kg/cm²) minimum.

3. Floors must be level with no cracks or holes.

E. POWER SUPPLY

The electrical source must be 3kw minimum. The source cable size must be 2.5mm²

and in good condition of contacting with floor.

Fig. 5

Concrete intensity must be 3,000psi

6”

¾”

Fig.4

III.INSTALLATION STEPS

A. Location of installation

Check and ensure the installation location (concrete, layout, space size etc.) is

suitable for lift installation.

B. Use a carpenter’s chalk line to establish installation layout of columns (See Fig. 6).

C. Check the parts before assembly.

1. Packaged lift, hydraulic power unit and parts box: (See Fig. 7).

2. Move the lift aside with a forklift or hoist and open the outer packing carefully

(See Fig. 8).

Shipment Parts list

Top beam Assy.

Fig. 7

Fig. 8

Chalk Line

150 ¾”

Fig. 6

Parts box

3. Remove 2 outer columns, then move the inner column to the installation site.

(See Fig. 9).

4. Lift the upper column with a forklift or hoist, loosen the bolts of the upper package

stand, then take out the parts in the inner column (See Fig. 10).

5. Lift the lower column with a forklift or hoist, take down the package stand, than take

off the lower outer column, take out the parts in the inner column (See Fig. 11).

Fig. 9

Fig. 10

Fig. 11

Open the

package

Lift the lower column

with a forklift or hoist

6. Move aside the parts and check the parts according to the shipment parts list

(See Fig. 12 & Fig. 13)

7. Check the parts of the parts bag 1#according to parts bag list (See Fig. 14).

8. Check the parts of the parts bag 2#according to parts bag list (See Fig. 15).

Parts list

Fig. 12

Fig. 14

Fig. 15

111

Parts box list (111)

Fig. 13

D. Install parts of outer columns (See Fig. 16).

E. Install hydraulic cylinder

Apply thread tape to both ends of extended straight fitting, connect the 90° fitting, connect

both to cylinder, and then install the cylinder in the carriages (See Fig. 17).

Fig. 16

F. Install columns

Lay down two columns on the installation site parallel, position the power-side column

according to the actual installation site. Usually, it is suggested to install power-side column on

the right side of vehicles drive-in. This lift is designed with 2-Section columns, adjust height

according to the ceiling height and by connecting the inner and outer columns as shown in Fig

18 or Fig 19.

If the ceiling height is over 199”, it can be installed in a high setting; if the ceiling height

between 175”–199”, it can be installed in the low setting; it is not recommended to install if the

ceiling height less than 175”.

1. High Setting, connecting the extension columns with the lower hole (See Fig. 18).

2. Low Setting: connecting the extension columns with the upper hole (See Fig.19).

Fig. 17

Fig. 18 High Setting

Place fitting in the cylinder toward the hole

Assemble the

cylinder into the

column

Fig. 19 Low Setting

Seal

tape

Andere Handbücher für PV-12PX

Inhaltsverzeichnis

Andere Atlas Hebesystem Handbücher

Atlas

Atlas BP10000X Bedienungsanleitung

Atlas

Atlas 14KOF-EXT Bedienungsanleitung

Atlas

Atlas 90HSC Bedienungsanleitung

Atlas

Atlas 412 Bedienungsanleitung

Atlas

Atlas BP10000 Bedienungsanleitung

Atlas

Atlas PV-10P Betriebsanleitung

Atlas

Atlas PV-15PX Bedienungsanleitung

Atlas

Atlas Kwik Bay Bedienungsanleitung

Atlas

Atlas PV-12PX Bedienungsanleitung

Atlas

Atlas 414 Bedienungsanleitung

Atlas

Atlas BP10000 Bedienungsanleitung

Atlas

Atlas BP12000X Bedienungsanleitung

Atlas

Atlas PV-10PX Bedienungsanleitung

Atlas

Atlas BP8000 Bedienungsanleitung

Atlas

Atlas BP12000 Bedienungsanleitung

Atlas

Atlas BP8000 Bedienungsanleitung

Atlas

Atlas APEX-10 Bedienungsanleitung

Atlas

Atlas LR10 Bedienungsanleitung

Atlas

Atlas OH-10X Bedienungsanleitung

Atlas

Atlas pv-15p Bedienungsanleitung

Atlas

Atlas SUNFLOOD Bedienungsanleitung

Atlas

Atlas PV-10PX Bedienungsanleitung

Atlas

Atlas PV-15PX Bedienungsanleitung

Atlas

Atlas PV-12PX Bedienungsanleitung

Beliebte Hebesystem Handbücher anderer Marken

morse

morse 82H-124 Bedienungsanleitung

Braun

Braun NL955 Series Bedienungsanleitung

haacon

haacon 1889.10 Bedienungsanleitung

Protekt

Protekt AT 252 Bedienungsanleitung

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Bedienungsanleitung

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Bedienungsanleitung

Genie

Genie Z-60/34 Bedienungsanleitung

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Bedienungsanleitung

Custom Equipment

Custom Equipment Hy-Brid 3 Series Programmierhandbuch

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Programmierhandbuch

BERG

BERG BeNomic EasyLeaf Bedienungsanleitung

Powermate

Powermate LiftGate LG-3 Bedienungsanleitung

Snorkel

Snorkel TM12 Series Bedienungsanleitung

Terberg

Terberg OMNIDEKA Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL625 Betriebsanleitung

Rotary

Rotary SPO16 Bedienungsanleitung