Atmel AT89C51 Montage- und Bedienungsanleitung
5-111
Designing
Boards with
Atmel Flash
Microcontrollers
Application
Note
Microcontroller
Designing Boards with Atmel AT89C51,
AT89C52, AT89C1051, and AT89C2051 for
Writing Flash at In-Circuit Test
Recent improvements in chips and
testers have made it possible for the
tester to begin taking over the role tradi-
tionally assigned to the PROM program-
mer. Instead of having a PROM pro-
grammer write nonvolatile memories
before assembling the board, the in-cir-
cuit tester writes them during in-circuit
testing operations. Many Teradyne Z18-
series testers are now in use loading
code into nonvolatile memories, micro-
controllers and in-circuit programmable
logic devices. The purpose of this note is
to explain how the Z18 approaches the
writing task for Atmel AT89C series IC’s,
so that designers of boards using these
chips can get the best results.
To write the flash memories embedded
in the Atmel AT89C series chips, the
Z18-family tester must be equipped with
the Digital Function Processor (DFP)
option.
The Atmel Technical Brief titled “Inte-
grated Flash Memory Gives AT89C51
In-System Reprogrammability” describes
two approaches, one parallel and the
other serial. The Teradyne Z18XX tester
with DFP can work with either, but this
paper will only discuss the parallel
approach. The serial method looks sim-
pler at first glance, but you must con-
sider that the AT89C series which serves
as the serial interface must also have its
code loaded by the tester. At some point,
therefore, the parallel method must be
used.
The Parallel Approach
There are some simple, yet important,
design constraints for the parallel
approach, as pointed out in the Atmel
Technical Brief. If these constraints have
not been observed during board design,
it may not be possible for a tester to write
the chip’s flash memory, and the chip will
have to be written with a PROM pro-
grammer before being installed on the
board. There are four main ways to inter-
fere with the tester’s attempts to write
the flash memory. The four Don’ts:
• Don’t tie needed input pins to VCC or
ground;
• Don’t tie needed input pins to outputs
of other IC’s;
• Don’t tie supervoltage input pins to
components that won’t tolerate the
voltage;
• Don’t tie output pins needed for
checking the write operation to other
IC outputs.
It is always possible to design a board
within the constraints described here.
The Atmel Technical Brief points out
specific pins that need attention, and
explains how to work with these pins to
insure in-circuit writability. These are dis-
cussed in detail below.
EA/VPP (AT89C51/52) or
RST/VPP (AT89C1051/2051)
The tester will take this pin high during
flash memory write and erase opera-
tions. EA/VPP (AT89C51/52) or RST/VPP
(AT89C1051/2051) will generally be
fixed either high or low when the board is
carrying out its normal mission, depend-
ing on whether the application uses
external addressing or runs entirely on
its internal memory. There are four
things to remember about this pin.
1. In certain parts of the Atmel doc-
umentation, Atmel recommends Rev. 0534B-A–12/97
Microcontroller
5-112
that this pin be “strapped” to VCC or ground. Please
interpret the word “Strapped” to mean “connected
by a 500 Ωresistor.” The resistor will supply the
desired 0 or 1 logic level during normal board oper-
ation, but the tester can also change the level easily
as needed when testing the microcontroller or when
writing its flash memory.
2. The pin must be accessible to the tester, i.e. it must
be contactable by a probe in a vacuum fixture (bed-
of-nails fixture).
3. Atmel makes two versions of the microcontroller.
One writes flash memory with 5 volts on this pin; the
other writes flash memory with 12 volts on this pin.
If you are using the 12-volt part, and if you need to
connect other components to the EA/VPP pin for any
reason, you will need to provide some way of pro-
tecting the other components from being damaged
by the 12-volt level. The AT89C1051/2051 are only
available with 12-volt programming.
4. For the AT89C1051/2051, if an RC circuit is used to
generate power-up reset, don’t tie the capacitor
directly to the RST pin. Put a resistor in between so
that the tester will not have to take time charging the
capacitor to 12 volts with each programmed byte.
Figure 1. Allow the tester to control EA/VPP/RST, and pro-
tect surrounding devices.
Note: 1. Only for the AT89C51 or AT89C52
Data Ports (P0, P1, P2, P3 for AT89C51/52 and
P1, P3 for AT89C1051/2051)
The normal mission of the board may set these ports up to
be outputs, or inputs, or a mix of outputs and inputs. During
flash memory write and erase operations, the tester will
apply signals to some of these pins, and attempt to read
signals from others. Outputs of other circuits on the board
may be exposed to excessive backdrive, or may interfere
with output signals trying to come from the microcontroller.
There are three things to remember about these pins.
1. The pins must be accessible to the tester, i.e. it
must be contactable by probes in a vacuum fixture.
2. If any other chips have their outputs connected to
pins used as inputs, they must be protected from
backdrive signals coming from the tester. Pass such
signals through disableable buffers as shown in Fig-
ure 2 below. Alternatively you may insert a 500 Ω
resistor in series with such an output as also shown
in Figure 2 below. The resistor will limit the back-
drive current to 5 volts/500 ohms = 10 milliamps.
The port pins used as inputs are all of P0, all of P1,
P2.0-P2.4, P2.6, P2.7, P3.6, and P3.7 for the
AT89C51/52 and P1 for the AT89C1051/2051.
Figure 2. Allow the tester to assert signals safely on micro-
controller pins that serve as inputs during flash memory
writing and erasing.
Note: 1. For the AT89C1051/2051 the tester disable P1 input
signals originating on the board during flash mem-
ory writing and erasing.
3. If any other chips have their outputs connected to
pins used as outputs during flash memory writing
and erasing operations, pass such signals through
disableable buffers as shown in Figure 3. Attempt-
ing to isolate with a 500 Ωresistor will not work,
due to the small amount of output current available
from the device. A 10K pullup is required to ensure
an adequate high for the tester to measure. The
port pins used as inputs are all of P0 and P3.4 for
the AT89C51/52 and P1 for the AT89C1051/2051.
Microcontroller
5-113
Figure 3. Be sure spurious signals do not conflict with
AT89C51/52 pins used as outputs during flash writing and
erasing.
Note on Lock Bits
Do not program the DFP to set any of the Lock Bits until
you are certain the other parts of the flash writing program
have been fully debugged.
DFP Wiring
One possible way of wiring the DFP to write the devices is
described in the tables. Two DR2p cards (that is, one from
the base unit and one expansion kit) are required for one
AT89C51/52 chip, and one DR2p card is required for each
AT89C1051/2051 chip on the board.
Using the Atmel AT89C51 or AT89C52
RST
The tester will take this pin high during flash memory write
and erase operations. It will be low when the board is carry-
ing out its normal mission, unless frequent resetting is an
integral part of the board’s normal mission. There are three
things to remember about this pin.
1. Most AT89C52 circuits have a simple RC reset cir-
cuit in which a large capacitor is wired between the
RST pin and ground. When the tester drives the
RST pin high to initiate an erasure or writing of the
flash memory, several microseconds may be
required to allow the tester's channel driver to
charge the capacitor.
2. The pin must be accessible to the tester, i.e. it must
be contactable by probe in a vacuum fixture.
3. Because the tester will force the pin high, you must
design other circuitry on this pin to permit and toler-
ate the forced high.
PSEN
The tester takes this pin low during flash memory write and
erase operations. Other than that, it is not supposed to be
connected to anything else. There is one thing to remem-
ber about this pin.
1. The pin must be accessible to the tester, i.e. it must
be contactable by probe in a vacuum fixture.
ALE/PROG
This pin is normally an output from the chip, but the tester
will use it as a command strobe input during flash memory
write and erase operations. There are three things to
remember about this pin.
1. The pin must be accessible to the tester, i.e. it must
be contactable by a probe in a vacuum fixture.
2. If any other chips have their outputs connected to
this pin (unlikely, but please check) they must be
capable of being disabled by the tester. Alternatively
you may design a 500 Ωresistor in series with such
an output. The resistor will protect the other chip
from excessive backdrive, and will also prevent the
other chip from volunteering spurious strobes dur-
ing the flash memory writing or erasing processes.
Figure 4. 500 Ωresistor allows the tester to drive the
ALE/PROG for AT89C51/52 or P3.2 (AT89C1051/2051)
pin easily and keeps downstream circuits from seeing
unusual activity.
3. Flash memory writing and erasing cycles generate
activity in other parts of the circuit. If any other chips
or subsystems on the board are designed to
respond to the ALE signal, they will receive unusual
instructions during the writing and erasing cycles.
Be sure that this unusual activity does not damage
them. Things to look for are other in-circuit writable
nonvolatile devices, fusible squibs, etc. If any such
exist, the 500 Ωresistor method described above
for disabling outputs will also the tester to prevent
the sensitive subsystems from seeing the unusual
ALE activity.
Microcontroller
5-114
Clock
The AT89C51/52 Clock must be running during flash writ-
ing. Most boards have clock circuits which will be normally
running while the board is on its fixture with power applied.
If the program contains a feature that disables the clock,
you will need to defeat it for the duration of this test page. If
you use a single-chip fixture to debug your application, you
will need to add a crystal in the single-chip fixture.
AT89C51/52 Pin Name DR2p Signal Name/Node# Notes
P0.0 192 (DR2p 0 - group A) Portwise Bidirectional
P0.1 193 (DR2p 0 - group A)
P0.2 194 (DR2p 0 - group A)
P0.3 195 (DR2p 0 - group A)
P0.4 196 (DR2p 0 - group A)
P0.5 197 (DR2p 0 - group A)
P0.6 198 (DR2p 0 - group A)
P0.7 199 (DR2p 0 - group A)
P1.0 (A0) 224 (DR2p 1 - group A and B) Address counter - 13 bits
P1.1 (A1) 225 (DR2p 1 - group A and B)
P1.2 (A2) 226 (DR2p 1 - group A and B)
P1.3 (A3) 227 (DR2p 1 - group A and B)
P1.4 (A4) 228 (DR2p 1 - group A and B)
P1.5 (A5) 229 (DR2p 1 - group A and B)
P1.6 (A6) 230 (DR2p 1 - group A and B)
P1.7 (A7) 231 (DR2p 1 - group A and B)
P2.0 (A8) 232 (DR2p 1 - group A and B)
P2.1 (A9) 233 (DR2p 1 - group A and B)
P2.2 (A10) 234 (DR2p 1 - group A and B)
P2.3 (A11) 235 (DR2p 1 - group A and B)
P2.4 (A12) 236 (DR2p 1 - group A and B)
P2.6 200 (DR2p 0 - group B) Outputs from DFP to DUT
P2.7 201 (DR2p 0 - group B)
P3.6 202 (DR2p 0 - group B)
P3.7 203 (DR2p 0 - group B)
RST 204 (DR2p 0 - group B)
EA/VPP 205 (DR2p 0 - group B)
ALE/PROG 206 (DR2p 0 - group B)
PSEN 207 (DR2p 0 - group B)
P3.4 (RDY/BUSY) 208 (DR2p 0 - group C) Input from DFP to DUT
Microcontroller
5-115
Using the Atmel AT89C1051 or
AT89C2051
XTAL1
The tester will apply logic level signals to this pin during
flash memory write and erase operations. There are two
things to remember about this pin.
1. The pin must be accessible to the tester, i.e. it must
be contactable by probe in a vacuum fixture.
2. Because the tester will force high and low signals
on this pin, you must design other circuitry on this
pin to permit and tolerate the logic level signals
applied by the tester.
P3 Pins P3.2 .. P3.5 and P3.7
The tester applies logic level signals to these five pins dur-
ing flash memory write and erase operations. There are
three things to remember about this group of pins.
1. The pins must be accessible to the tester, i.e. they
must be contactable by probes in a bed-of-nails fix-
ture.
2. If your application uses these pins as inputs, and
any other chips have their outputs connected to
these pins, the other chips’ outputs must be capable
of being disabled by the tester, or in any case must
tolerate the logic level high and low signals applied
by the tester. Alternatively you may design a 500 Ω
resistor in series with the other chip’s outputs. The
resistor will protect the other chip from excessive
backdrive, and will also prevent the other chip from
interfering with the tester’s signals during the flash
memory writing or erasing processes. Pay special
attention to intermittent signal sources such as
interrupts or external or external timing inputs that
are usually connected to P3.2, P3.3, P3.4.
3. Flash memory writing and erasing cycles generate
activity in other parts of the circuit. If any other chips
or subsystems on the board are designed to
respond to the P3 signals, they will receive unusual
instructions during the writing and erasing cycles.
Be sure that this unusual activity does not damage
them. Things to look for are other in-circuit writable
nonvolatile devices, high current drivers, fusible
squibs, etc. If any such exist, the 500 Ωresistor
method described for RST will also allow the tester
to prevent the sensitive subsystems from seeing the
unusual signal activity. Because the flash writing
signals are logic level, not 12-volt, the zener diodes
noted for RST are not necessary on the P3 signals.
See Figure 4.
Note on VPP
Generation of VPP by the DFP on channel 223 presents no
danger to the conventional digital driver and receiver on
channel 223, because the conventional driver and receiver
are disconnected by a D relay during DFP operations. In
your DFP program, make sure to set VPP to zero and dis-
connect the VPP relay before exiting from ptprog.c.
AT89C1051/205252 Pin Name DR2p Signal Name/Node# Notes
P1.0 192 (DR2p 0 - group A) Portwise Bidirectional
P1.1 193 (DR2p 0 - group A)
P1.2 194 (DR2p 0 - group A)
P1.3 195 (DR2p 0 - group A)
P1.4 196 (DR2p 0 - group A)
P1.5 197 (DR2p 0 - group A)
P1.6 198 (DR2p 0 - group A)
P1.7 199 (DR2p 0 - group A)
P3.2/PROG 200 (DR2p 0 - group B) Outputs from DFP to DUT
P3.3 201 (DR2p 0 - group B)
P3.4 202 (DR2p 0 - group B)
P3.5 203 (DR2p 0 - group B)
P3.7 204 (DR2p 0 - group B)
RST/VPP 223 (DR2p 0 - group D) VPP supplied by DFP
Andere Handbücher für AT89C51
1
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere Atmel Computerhardware Handbücher
Atmel
Atmel AT88CK201STK Bedienungsanleitung
Atmel
Atmel AT89STK-06 CAN Installationshandbuch
Atmel
Atmel AVR ATICE10 Bedienungsanleitung
Atmel
Atmel AT86RF211 Bedienungsanleitung
Atmel
Atmel FingerChip FCDEMO4 Montage- und Bedienungsanleitung
Atmel
Atmel AT91CAP9 Bedienungsanleitung
Atmel
Atmel SMART SAMA5D3 Series Bedienungsanleitung
Atmel
Atmel AVR STK500 Bedienungsanleitung
Atmel
Atmel STK600-RC064SAM-72 Bedienungsanleitung
Atmel
Atmel SAM W25 Xplained Pro Bedienungsanleitung
Atmel
Atmel SMART ATBTLC1000 Bedienungsanleitung
Atmel
Atmel ATSAMD21BLDC24V-STK Bedienungsanleitung
Atmel
Atmel ARM Thumb AT91 Installationshandbuch
Atmel
Atmel 7698AAUTO01/07 Bedienungsanleitung
Atmel
Atmel AT04357 RCB256RFR2-XPRO Bedienungsanleitung
Atmel
Atmel AVR ATmega88PA Bedienungsanleitung
Atmel
Atmel AT91CAP9-STK Bedienungsanleitung
Atmel
Atmel AT91MEC01 Bedienungsanleitung
Atmel
Atmel ATWINC1500 Bedienungsanleitung
Atmel
Atmel ATBTLC1000 BluSDK Bedienungsanleitung
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
