Atmel ATSAMB11 BluSDK SMART Bedienungsanleitung
ATSAMB11 BluSDK SMART
HID Mouse Device - Getting Started Guide
USER GUIDE
Introduction
The HID over GATT (HOGP) profile defined by the Bluetooth®SIG enables support of HID services over a
Bluetooth Low Energy (BLE) protocol stack using Generic Attribute profile (GATT). This allows devices
like keyboard or mouse implementing HOGP to connect to a compatible HOGP/BLE host device (e.g.:
Mobile Phone, Tablet, TV, etc.)
The HOGP Mouse device application example (referred as HID Mouse device in this document) supports
the following features:
Advertisement
Pairing
Services: HID Service and Device Information Service.
Report Mode (Mouse)
The HID Mouse device application example supports the following characteristics for HID service:
Protocol Mode
Report
Boot Mouse Input Report
Report Map
HID Information
HID Control Point
For the purpose of demonstration, the example application simulates the function of a mouse. Once the
handshake and connection procedure between a mobile phone and the Atmel®ATSAMB11 emulating a
mouse device example is completed, a mouse cursor will appear on the mobile device’s screen. Pressing
the button on the ATSAMB11 platform simulates movement of mouse in a pre-defined pattern as
described in later in this document.
Atmel-42603A-ATSAMB11-BluSDK-SMART-HID-Mouse-Device-Getting-Started-Guide_UserGuide_112015
ATSAMB11 BluSDK SMART –HID Mouse Device –Getting Started Guide [USER GUIDE]
Atmel-42603A-ATSAMB11-BluSDK-SMART-HID-Mouse-Device-Getting-Started-Guide_UserGuide_112015
2
2
Table of Contents
1Purpose .....................................................................................................................3
2Demo Setup..................................................................................................................3
3Hardware Setup ...........................................................................................................3
4Software Setup.............................................................................................................4
4.1 Installation Steps...................................................................................................................................4
4.2 Build Procedure.....................................................................................................................................4
5Console Display...........................................................................................................6
6Running the Demo.......................................................................................................6
7BluSDK SMART Software Architecture....................................................................11
8ATMEL EVALUATION BOARD/KIT IMPORTANT NOTICE AND DISCLAIMER........12
9Revision History ........................................................................................................13
ATSAMB11 BluSDK SMART –HID Mouse Device –Getting Started Guide [USER GUIDE]
Atmel-42603A-ATSAMB11-BluSDK-SMART-HID-Mouse-Device-Getting-Started-Guide_UserGuide_112015
3
3
1 Purpose
This getting started guide describes the setup of an Atmel ATSAMB11 Xplained board and bringing up an
example profile supplied as part of BluSDK SMART release. This document explains the bring-up of HID
Mouse device example application that is embedded as part of the software release package.
2 Demo Setup
3 Hardware Setup
Connect the ATSAMB11 board to the host PC using a Micro-USB cable.
Figure 3-1. EDBG USB Port
BLE Link
ATSAMB11
(HID Mouse Device
Application)
Android mobile phone
(HOGP Host role)
ATSAMB11 BluSDK SMART –HID Mouse Device –Getting Started Guide [USER GUIDE]
Atmel-42603A-ATSAMB11-BluSDK-SMART-HID-Mouse-Device-Getting-Started-Guide_UserGuide_112015
4
4
4 Software Setup
4.1 Installation Steps
1. Install the latest Atmel Studio [Atmel Studio 7.0 (build 629 or later) web installer
(recommended)]
http://www.atmel.com/tools/ATMELSTUDIO.aspx.
2. Install the latest Atmel Software Framework.
This package will install the following examples within the Atmel Studio environment:
HID Device Application for ATSAMB11
4.2 Build Procedure
The following procedure is explained for ATSAMB11 application example.
1. Select New Example Project.
Figure 4-1. Creating a New Example Project
2. Select “SAMB11” in device family, enter “ble-hid mouse” in the search window, and expand Atmel
Corp Projects. The location and the name of the project can be selected in the respective fields.
Click OK.
Figure 4-2. Selecting HID Device Application from Example Projects
3. Accept the license Agreement. The studio will generate the BLE-HID Mouse project for ATSAMB11.
4. Build the solution.
ATSAMB11 BluSDK SMART –HID Mouse Device –Getting Started Guide [USER GUIDE]
Atmel-42603A-ATSAMB11-BluSDK-SMART-HID-Mouse-Device-Getting-Started-Guide_UserGuide_112015
5
5
Figure 4-3. Building the HID Device Application
5. Download the application via the USB to the ATSAMB11 board by using the Device Programing
option available in Tools as shown below.
Figure 4-4. Selecting Device Programming Option
6. Inside the device programming the user has to select the correct configuration for the device and
finally program the device by using the program button.
Figure 4-5. Flashing the Application on Atmel MCU
ATSAMB11 BluSDK SMART –HID Mouse Device –Getting Started Guide [USER GUIDE]
Atmel-42603A-ATSAMB11-BluSDK-SMART-HID-Mouse-Device-Getting-Started-Guide_UserGuide_112015
6
6
5 Console Display
For the purpose of debugging, logging is made available through a serial console. The logging interface
utilizes the same COM port that connects to ATSAMB11. A serial port monitor application (for example
TeraTerm) shall be opened and attached to the appropriate COM port enumerated by the device on the
PC.
6 Running the Demo
1. Power on the ATSAMB11 by connecting the USB cable.
2. On the PC, open any Terminal Application (e.g. TeraTerm). Select the appropriate COM Port.
(Settings: Baudrate 115200, None Parity, one Stop bit, one Start bit, no Hardware Handshake.)
3. Press the Reset button on the ATSAMB11 board.
4. The board is now in advertising mode as shown below.
Figure 6-1. HID Keyboard Device in Advertising Mode
Initializing HID Mouse Application
HID Profile Configured
Initializing SAMB11
BLE-chip id : 0x002000B0
BD Address:0xF8F005F0B299, Address Type:0
Device Started Advertisement
5. The demo requires use of an Android mobile phone supporting HOGP. The HOGP profile is natively
supported in Android from version 4.4 (Android KitKat) and upwards. In Bluetooth settings scan for
the devices. The device with “ATMEL-HID” will be found as shown below. Click on “ATMEL-HID” to
get connected.
Figure 6-2. Mouse Device Discover on Bluetooth Device
6. Once the user clicks on “ATMEL-HID”, pairing procedure started.
ATSAMB11 BluSDK SMART –HID Mouse Device –Getting Started Guide [USER GUIDE]
Atmel-42603A-ATSAMB11-BluSDK-SMART-HID-Mouse-Device-Getting-Started-Guide_UserGuide_112015
7
7
Figure 6-3. Pairing Process with HID Device
7. Once the pairing done connected device is listed in paired device.
Figure 6-4. Connected Device Inside Paired Devices
8. Console log on HID device side for pairing and connection procedure.
Figure 6-5. HID Mouse Log for Pairing and Connection Procedure
Initializing HID Mouse Application
HID Profile Configured
Initializing SAMB11
BLE-chip id:0x002000B0
BD Address:0xF8F005F0B299, Address Type:0
Device Started Advertisement
Connected to peer device with address 0x7b5bfc5cf8d0
Connection Handle 0
Remote device request pairing
Sending pairing response
AT_BLE_CONN_PARAM_UPDATE
Pairing procedure completed successfully
9. Once the device connected to host (Phone). User can select button for simulating mouse
movement.
ATSAMB11 BluSDK SMART –HID Mouse Device –Getting Started Guide [USER GUIDE]
Atmel-42603A-ATSAMB11-BluSDK-SMART-HID-Mouse-Device-Getting-Started-Guide_UserGuide_112015
8
8
Figure 6-6. Press Button for Mouse Movement
10. For every press on button, the user can see corresponding cursor movement on HID host as
described below:
First 5 Button Press: Cursor moves right
Next 5 Button Press: Cursor moved down
Next 5 Button Press: Cursor moves left
Next 5 Button Press: Cursor moved up
The same sequence is repeated based on user input. A snapshot of the console logs are shown below.
ATSAMB11 BluSDK SMART –HID Mouse Device –Getting Started Guide [USER GUIDE]
Atmel-42603A-ATSAMB11-BluSDK-SMART-HID-Mouse-Device-Getting-Started-Guide_UserGuide_112015
9
9
Figure 6-7. HID Device Console Log for Movement
Mouse Right Movement
Mouse Right Movement
Mouse Right Movement
Mouse Right Movement
Mouse Right Movement
Mouse Down Movement
Mouse Down Movement
Mouse Down Movement
Mouse Down Movement
Mouse Down Movement
Mouse Letf Movement
Mouse Letf Movement
Mouse Letf Movement
Mouse Letf Movement
Mouse Letf Movement
Mouse UP Movement
Mouse UP Movement
Mouse UP Movement
Mouse UP Movement
Mouse UP Movement
Figure 6-8. Mouse Cursor Position on Phone
ATSAMB11 BluSDK SMART –HID Mouse Device –Getting Started Guide [USER GUIDE]
Atmel-42603A-ATSAMB11-BluSDK-SMART-HID-Mouse-Device-Getting-Started-Guide_UserGuide_112015
1
0
10
Figure 6-9. Mouse Move Simulation
Andere Handbücher für ATSAMB11 BluSDK SMART
6
Inhaltsverzeichnis
Andere Atmel Mikrocontroller Handbücher
Atmel
Atmel AVR XMEGA AU series Bedienungsanleitung
Atmel
Atmel AT97SC3205T-SDK2 Bedienungsanleitung
Atmel
Atmel AT90S4433-8AC Bedienungsanleitung
Atmel
Atmel ATZB-EVB-24-SMA Bedienungsanleitung
Atmel
Atmel AVR ATtiny10 Series Bedienungsanleitung
Atmel
Atmel AVR1019 Montage- und Bedienungsanleitung
Atmel
Atmel AT32UC3L064 Bedienungsanleitung
Atmel
Atmel ATF15 DK3-U Series Bedienungsanleitung
Atmel
Atmel ATmega324PB Bedienungsanleitung
Atmel
Atmel AVR1921 Montage- und Bedienungsanleitung
Atmel
Atmel AVR AT90CAN32 Bedienungsanleitung
Atmel
Atmel AT88CK109STK3 Installationshandbuch
Atmel
Atmel AT91 Series Bedienungsanleitung
Atmel
Atmel AVR AT90S2333 Bedienungsanleitung
Atmel
Atmel AVR1909 Installationshandbuch
Atmel
Atmel ATF15 DK2 Series Bedienungsanleitung
Atmel
Atmel ATmega328PB Xplained Mini Montage- und Bedienungsanleitung
Atmel
Atmel SAM4L Xplained Pro Bedienungsanleitung
Atmel
Atmel AT91 Series Bedienungsanleitung
Atmel
Atmel AVR Bedienungsanleitung
Beliebte Mikrocontroller Handbücher anderer Marken
AMS
AMS AS7261 Demo Kit Bedienungsanleitung
Novatek
Novatek NT6861 Bedienungsanleitung
Espressif Systems
Espressif Systems ESP8266 SDK Einrichtungshandbuch
Nuvoton
Nuvoton ISD61S00 ChipCorder Leitfaden
STMicrolectronics
STMicrolectronics ST7 Assembler Linker Bedienungsanleitung
Texas Instruments
Texas Instruments Chipcon CC2420DK Bedienungsanleitung
Lantronix
Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung
NEC
NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung
Mikroe
Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung
Intel
Intel Agilex Bedienungsanleitung
Cypress
Cypress CY4607 HX2VL Bedienungsanleitung
DIGITAL-LOGIC
DIGITAL-LOGIC MICROSPACE Bedienungsanleitung
Texas Instruments
Texas Instruments TMS320F2837 D Series Bedienungsanleitung
CYPRES
CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung
Texas Instruments
Texas Instruments INA-DUAL-2AMP-EVM Bedienungsanleitung
Espressif Systems
Espressif Systems ESP8266EX Betriebsanleitung
Abov
Abov AC33M8128L Bedienungsanleitung
Laird
Laird BL654PA Bedienungsanleitung