ATO BT20 Bedienungsanleitung

User Guide Page 1

AATTOaa A BBLLUUEETTOOOOTTHHHHEEAADDSSEETT

First Edition, July 2001

Rm. 1314-16, 13/F

Block B1, Yau Tong Industrial City

17 Ko Fai Road

Yau Tong, Kowloon

Hong Kong

FEDERAL COMMUNICATIONS COMMISSION

INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Any changes or modifications not expressly approved by the grantee of this

device could void

the user's authority to operate the equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth foran

uncontrolled environment. This device and its antenna must not be co-located

or operating in conjunction with any other antenna ortransmitter.

User Guide Page 2

Table of Content

Table of ContentTable of Content

Table of Content

Introduction................................................................................................ 3

ATO Bluetooth Headset BT20............................................................ 3

Usage Requirement............................................................................ 3

Appearance ............................................................................................... 4

Putting On the Headset.............................................................................. 5

Adjust the ear hook for left-ear use............................................................ 6

Charging the battery.................................................................................. 7

Turn on the Headset.................................................................................. 8

Turn off the Headset.................................................................................. 8

Pairing........................................................................................................ 9

Bluetooth Passkey.............................................................................. 9

Pairing the Headset.......................................................................... 10

Adjusting the Listening Volume................................................................ 11

Making and Receiving Calls with a Bluetooth Mobile phone.................... 12

Making and Receiving Calls with a Mobile phone with ATO Mobile Phone

Adaptor installed...................................................................................... 13

Transferring Sound from a Bluetooth Mobile Phone to Headset.............. 14

Transferring Sound from Headset to a Bluetooth Mobile Phone.............. 14

Transferring Sound from a Mobile phone with ATO Mobile Phone Adaptor

installed to Headset ................................................................................. 14

Transferring Sound from the Headset to a Mobile phone with ATO Mobile

Phone Adaptor installed........................................................................... 14

User Guide Page 3

Introduction

IntroductionIntroduction

Introduction

ATABluetoothTM Headset BT20

The ATO Bluetooth Headset BT20 is a portable handsfree audio device based

on Bluetooth wireless technology.

Bluetooth wireless technology is a global specification for personal area

wireless connectivity to ensure communication compatibility worldwide.It

connects any portable and stationary communication device easily without a

single inch of cable.

You can connect your wireless headset to your mobile phone, computer or any

Bluetooth-enabled products that support the Headset Profile1(as an audio

gateway2), so as to free your hands for other valuable tasks.

This User's Guide shows you how to use the Headset with the other Bluetooth

device such as a mobile phone or a PC.

You can handle incoming and outgoing calls, transfer an ongoing call, and

adjust the listening volume by using the two buttons on the Headset.

Usage Requirement

You can use the Bluetooth Headset with any device that is compatible with

Bluetooth wireless technology and supports the Headset Profile (as audio

gateway).

To use the Headset together with a mobile phone, you need to have a

Bluetooth-enabled phone or a phone with a Bluetooth adapter connected to it.

1Headset Profile – Defined by the Bluetooth Special Interest Group (SIG), it describes how

manufactures should implement the various features supported by a Bluetooth Headset.

2Audio Gateway - The device that is the gateway of the audio, both for input and output. Typical

Audio Gateways are mobile phones and personal computers

User Guide Page 4

Appearance

AppearanceAppearance

Appearance

User Guide Page 5

Putting On the Headset

Putting On the HeadsetPutting On the Headset

Putting On the Headset

To put the Headset on your right ear:

1. Put on the Headset and make the hanger behind and holding your ear.

2. Rotate the Headset a bit such that the microphone is pointing towards

your mouth.

User Guide Page 6

Adjust the ear hook for left

djust the ear hook for leftdjust the ear hook for left

djust the ear hook for left-

-ear use

ear useear use

ear use

To wear the Headset on your left ear:

1. Gently turn the hanger to the opposite direction as shown.

2. Flip the headset to left ear side to wear it on.

3. Rotate the headset a bit such that the microphone is pointing towards your

mouth.

User Guide Page 7

Charging

ChargingCharging

Charging the battery

the batterythe battery

the battery

The Headset has a built-in rechargeable battery. You need to charge the

Headset before using it for the first time.

The indicator on the Headset will flash RED if the battery needed to be

recharged.

To charge the battery,

1. Connect the supplied external charger to AC main.

2. Plug the DC plug of the external charger into the DC jack located at the

end of the Headset to charge the battery.

3. It takes about 1 hour to fully recharge the battery.

4. During charging, the indicator light of the external charger is turned on.

When the battery is fully charged the indicator light is turned off.

User Guide Page 8

Turn

urnurn

urn on

onon

on the Headset

the Headsetthe Headset

the Headset

1. Press the ON/OFF button once, and the Headset indicator light flashes

green. The Headset is now ready to use.

2. If the battery is low, the Headset indicator light flashes red.

Turn

urnurn

urn off

offoff

off the Headset

the Headsetthe Headset

the Headset

1. Press and hold the ON/OFF button for about 3 seconds until the Headset

indicator light switches off.

2. To save battery power, turning off the headset after use is recommended.

User Guide Page 9

Pairin

PairinPairin

Pairing

Bluetooth Passkey

The Bluetooth passkey (or PIN) is used to validate two Bluetooth devices to

each other and create a trusted relationship between them. It is used to

prevent unauthorized use of a Bluetooth device by people other than the

owner of the device. The process of creating a trusted relationship between

two Bluetooth devices is called “Pairing” (see next section).

Each ATO Bluetooth headset has a unique passkey, which is stored in its

internal memory. You can find the value of the passkey from the supplied

user registration card. Whether you need to use the passkey during pairing

depends on the kind of Bluetooth device that the headset will be connected to:

1. ATO Mobile Phone Adaptor – If you are using the headset with a mobile

phone that has the ATO Mobile Phone Adaptor that comes with the

Headset installed, you don’t normally need to use the passkey. Please

refer to the ATO Mobile Phone Adaptor user guide for more detailed

information.

2. ATO PC Adaptor – If you are using the headset with a PC that has the

ATO PC Adaptor connected, depending on the configuration of the PC

software, you may be required to enter the passkey on the PC during

pairing. Please refer to the user guide of the ATO PC Adaptor for

detailed information.

3. Bluetooth Mobile Phone or other devices – If you want to use the headset

with a mobile phone or other devices with Bluetooth capability, you are

usually required to enter the passkey on that device during pairing.

Please refer to the user guide of the mobile phone for the specific

operation.

Inhaltsverzeichnis

Andere ATO Headset Handbücher

ATO

ATO EQ1 Bedienungsanleitung

Beliebte Headset Handbücher anderer Marken

Sena

Sena SMH10 Bedienungsanleitung

IASUS

IASUS Stealth IA-NT4-BASIC-BT Bedienungsanleitung

Sennheiser

Sennheiser EPOS ADAPT 230 Bedienungsanleitung

Doro

Doro Flexus HS2005 Bedienungsanleitung

GE 98971 Bedienungsanleitung

Hama

Hama 00184070 Bedienungsanleitung

Plantronics

Plantronics Blackwire 3200 Series Bedienungsanleitung

Blue Tiger

Blue Tiger Advantage PLUS Bedienungsanleitung

Jawbone

Jawbone Icon Bedienungsanleitung

Jabra

Jabra FR 20 Bedienungsanleitung

Roxcore

Roxcore Flow A+ Bedienungsanleitung

Turtle Beach

Turtle Beach XP 510 Bedienungsanleitung

Philips

Philips SHB6101 Bedienungsanleitung

Jabra

Jabra PRO 9460 Duo Bedienungsanleitung

HyperX

HyperX HyperX Cloud Flight Bedienungsanleitung

Bose

Bose MIE2 Mobile Bedienungsanleitung

Jabra

Jabra Steel Bedienungsanleitung

HyperX

HyperX cloud ii Bedienungsanleitung