Atom ATOM 3 Series Bedienungsanleitung

ATOM 3.5 USER'S MANUAL

Hello! Welcome to join Atom 3D printer family! Atom 3.5 is a

world-class desktop machine designed for speed, precision and

reliability. We know you’ll love printing your designs on Atom 3

but before you do, please read the manual thoroughly.

SAFETY WARNINGS AND GUIDELINES

P. 4

ATOM 3 SERIES: USER'S MANUAL

P.14

PREPARING TO PRINT

UPLOAD FILES/START PRITING

PRINTER SETTING

PACKAGE CONTENT

Auto-Leveling

Cleaning the Build Plate

Loading Filament

Unloading Filament

Swapping Hotends

Wi-Fi Setting

P. 8

P. 9

P.10

P. 11

P.12

P.12/13

P. 5

P. 6 / 7

CUSTOMER SERVICE

P. 5

CUSTOM SETTING

P.15

SAFETY CERTIFICATIONS

P.18

CARE AND MAINTENANCE

MIC

FCC

P.16

P.17

FILAMENT RUNOUT SENSOR

P.16

LANGUAGE SETTINGS

P.16

PRINTING ENVIROMENT

P.16

P.19

WARRANTY

P.20

REGULATORY

SAFETY WARNINGS AND GUIDELINES

Safety Warnings and Guidelines

1. Be careful not to damage the glass build plate.

2. Take care to avoid touching hot parts, including heat

blocks, nozzle, extruded filament, and the heated build

plate.

3. Keep the printer and all accessories out of reach of small

children.

4. Do not remove or disconnect the USB cable when printing

from a computer.

5. Do not pull or twist the black cable harness at any time.

6. Do not force or tear anything during unpacking and

setup. This may cause damage to the printer and/or its

accessories.

7. Do not reach inside the printer during operation. Always

allow the printer and extruded filament to cool before

reaching inside.

8. Ensure that the printer is turned o and unplugged from

its power source before making repairs or performing

service.

9. Do not install this device on an unstable surface where it

could fall and cause either personal injury or damage to

the device and/or other equipment.

10. Do not subject the product to extreme force, shock, or

uctuations in temperature or humidity.

11. This device is intended for indoor use only.

12. Do not expose this device to water or moisture of any

kind. Do not place drinks or other containers with moisture

on or near the device. If moisture does get in or on the

device, immediately unplug it from the power outlet and

allow it to fully dry before reapplying power.

13. Do not touch the device, the power cord, or any other

connected cables with wet hands.

14. Use only in a well-ventilated area. Do not use in conned

spaces.

15. Prior to operation, check the unit and power cord for

physical damage. Do not use if physical damage has

occurred.

16. Before plugging the unit into a power outlet, ensure that

the outlet provides the same type and level of power

required by the device.

Customer Service

ATOM is dedicated to ensuring that your ordering, purchasing,

and delivery experience is second to none. If you have any

problem with your order, please give us an opportunity to

make it right. You can contact an ATOM Customer Service

representative through the phone or email, also you can link on

our website www.atom3dp.com during normal business hours

(Mon-Fri: 9am-12pm, 1pm-6pm)

or via email at [email protected]

Software Installation and Setup

We recommend using Cura for use with both Atom 3.5 and

Atom 3.5 DX. Please visit Atom website to download Cura and

for instruction of installation. The installation package comes

with everything you need to get started.

https://www.atom3dp.com/en/

CCAH21LP1650T7

For low-power radio frequency equipment that has been certied, companies, rms,

or users are not allowed to change the frequency, increase the power, or change the

characteristics and functions of the original design without approval. The use of low-

power radio frequency equipment must not aect ight safety and interfere with legal

communications; if interference is found, it should be stopped immediately, and it can

only be used when there is no interference. The aforementioned legal communications

refer to radio communications operated in accordance with the provisions of the

Telecommunications Administration Law. Low-power radio frequency equipment must

endure the interference of legal communications or industrial, scientic and medical

radio wave radiation electrical equipment.

Package Contents

Please take an inventory of the package contents to ensure

you have all the items listed below. If anything is missing

or damaged, please contact Atom Customer Service for a

replacement.

Atom 3.5

• 1 x Atom 3.5 3D Printer

• 1 x Atom PLA Filament Roll (700g)

• 1 x Power Supply

• 1 x Power Supply AC cable

• 1 x Antenna

• 1 x Spare PTFE-lined Nozzle

• 1 x Auto-level Sensor

• 2 x Spool Axle

• 1 x Teon lubricants

• 1 x Shovel

• 1 x Diagonal pliers

• 1 x Screwdriver( H1.5 )

• 1 x Roll support rod

• 1 x Black hexagon socket screw M5-12mm

• 1 x Washer

• 1 x Retainer clip

CUSTOMER SERVICE/SOFTWARE INSTALLATION AND SETUP/PACKAGE CONTENTS

PRINTER SETTING

Follow below instruction before to print :

1. Take the 3D printer out of the package and place it on a stable surface

which near by the AC outlet.

2. Take out the magnetic rod and the mobile platform. In order to ensure

the magnetism of the magnetic rod, please avoid separating the two.

Note: The magnet of each magnetic rod is marked with N-level; those

not marked are S-level.

※ If the mobile platform and the magnetic rod are connected together, please

reconnect the two corresponding to the magnet (as shown in the picture)

3. Install the rod

4. Install Washer > Spool Axie > Filament Roll > Spool Axie

> Retainer Clip

The fan faces the front

6. Plug in the power and turn on the switch5. Install antenna

A. First lock the antenna horizontally into the screw

and tighten it

B. Fold up the antenna at the bend

PRINTER SETTING

Auto-Leveling

Before your rst print, and anytime you remove the build plate,

you’ll want to run an auto-level to ensure that your parts adhere

well to the glass. Follow the procedure below to run an auto-

level

1. Make sure the nozzle temperature is in room temperature

2. After connecting the automatic calibration sensor to the

green line of the mobile platform cable set, properly cover

the nozzle with the white sponge ring.

Please gently put the sensor

on the nozzle. If the nozzle

touches the plastic lm, it

will cause calibration errors.

Do not touch

the running fan

to avoid injury!

Connect the platform

calibration module cable

and the green connector

which above the nozzle

※Regardless of positive

and negative polarity

Automatic sensor

correction

PREPARING TO PRINT

011 Idle

Position

X 0 0

Y 0 0

Z 337 3

Bed Calibration Extrusion

Macro

Fan 0%

HOMEConsoleMove

STOPControlPrint Setup

Nozzle 1 Hot Bed

200 70

23.3 24.2

Note: Please gently put the sensor on the nozzle. If the

nozzle touches the plastic lm, it will cause calibration

errors.

011 Idle

Position

X 0 0

Y 0 0

Z 337 3

Bed Calibration Extrusion

Macro

Fan 0%

HOMEConsoleMove

STOPControlPrint Setup

Nozzle 1 Hot Bed

200 70

23.3 24.2

Clean the Build Plate

To prepare the build plate for printing, use rubbing alcohol and

a soft, lint-free cloth or white paper towel to remove any dust

and oil from the surface of the glass. DO NOT use colored paper

towels or white board cleaners.

3. Click [ Control ] > [ HOME ] > [ Bed Calibration ] on the

LCD screen to auto-leveling.

4. After the automatic calibration is completed, the automatic

calibration sensor will be removed

PREPARING TO PRINT

6. Touch the LCD screen to preheat the nozzle to the

working temperature of the material, for example,

PLA is 200° C.

1. Place the filament spool

on the holder so that

the working end of the

filament hangs down to

the right.

2. Cut the end of the

filament at an angle as

illustrated.

3. Gently straighten a

segment about 5 cm

(2”) from the end with

your ngertips to make it

easier to feed the lament

through the sensor and

the extruder.

4. Remove the filament

sensor from its holder

and feed the end of the

filament through the

sensor in the direction as

indicated by the arrow,

then into the tube on the

right side of the extruder.

5. Pinch the extruder idler

lever and push the

filament past the gear

and into the bowden tube

just past the pneumatic

connector.

Pass the coil to the beginning of the

circle shown in the gure

Place the Sensor Module

back when it is not in use.

Do not touch the heated nozzle

and the heated build plate to

avoid burn scald !

LOADING FILAMENT

011 Idle

Position

X 0 0

Y 0 0

Z 337 3

Bed Calibration Extrusion

Macro

Fan 0%

HOMEConsoleMove

STOPControlPrint Setup

Nozzle 1 Hot Bed

200 70

23.3 24.2

Loading Filament

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Atom 3D-Drucker Handbücher

Atom

Atom MacOS Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch