ATOMSTACK M150 Bedienungsanleitung
AtomStack M150 Laser Module
Installation Manual
Note: The picture is for reference only,the actual product shall prevail
For more information,please scan the QR code
Deutsche
Français
English
√
√
√
F03-0192-0AA1 Version: A
Part 1 : Security Statment and warning
Before Using the laser engraving, please read this safety guide carefully, it mentions situations that
require special attention and includes warnings of unsafe practices that can cause damage to your
property or even endanger your personal safety.
1. This product is a laser engraver system components, must be installed in other manufacturers of laser engraver for use.And the
product belongs to Class 4 laser products, the laser system itself must meet the requirements of IEC 60825-1 latest version, other-
wise the product is prohibited to be used.
2. Your laser engraver shall have a protective housing which, when in place, prevents human access to laser radiation.
3. If a protective housing is equipped with an access panel which provides "walk-in" access then:
a) means shall be provided so that any person inside the protective housing can prevent activation of a laser hazard that is equiva-
lent to Class 3B or Class 4.
b）a warning device shall be situated so as to provide adequate warning of emission of laser radiation equivalent to Class 3R in the
wavelength range below 400 nm and above 700 nm, or of laser radiation equivalent to Class 3B or Class 4 to any person who
might be within the protective housing.
c) where “walk-in” access during operation is intended or reasonably foreseeable, emission of laser radiation that is equivalent to
Class 3B or Class 4 while someone is present inside the protective housing of a Class 1, Class 2, or Class 3R product shall be
prevented by engineering means. NOTE Methods to prevent human access to radiation when persons are inside the protective
housing can include pressure sensitive floor mats, infrared detectors, etc.
01
4. The laser itself has a protective cover, the protective cover is fastened by screws. When the laser is installed on the laser engraver,
the protective cover should be checked to be reliably locked, and can not be removed in the energized state.
5. The housing of the laser engraver should have an interlock function. When the housing is opened or removed, the laser can be
automatically turned off.
6. The laser engraver should have an emergency stop button, which can immediately stop the output of the laser when pressed under
unexpected circumstances.
7. The laser engraver should have a reset button, which can resume work under the condition of confirming safety after lifting the
interlock or emergency stop.
8. Laser engraver should use physical keys, dongle, password system and other ways to manage and control, to prevent personnel
without security training operation of this kind of equipment.
9. On the laser engraver any window or channel that can actively observe or passively receive the laser radiation should be set up
warning marks.
10. If the laser burns the skin or eyes, please go to a nearby hospital for examination and treatment immediately.
02
Part 2 : Disclaimer and warning
This product is not a toy and is not suitable for people under 15 years of age. Do not allow children to touch the laser Module.
Please be careful when operating in scenes with children.
This product is a laser module, visit http://www.atomstack.com/laserengraverdownload for complete "user manual" and the latest
instructions and warnings. Shenzhen AtomStack Technologies Co., Ltd. (Atomstack) reserves the right to update this Disclaimer and
Safe Operation Guidelines.
Please be sure to read this document carefully before using the product to understand your legal rights, responsibilities and safety
instructions; Otherwise, it may bring property loss, safety accident and hidden danger of personal safety. Once you use this product,
you shall be deemed to have understood, accepted and accepted all terms and contents of this document. User undertakes to be
responsible for his or her actions and all consequences arising therefrom. User agrees to use the Product only for legitimate purpos-
es and agrees to the entire terms and contents of this document and any relevant policies or guidelines that AtomStack may
establish. You understand and agree that AtomStack may not be able to provide you with the cause of the damage or accident and
provide you with AtomStack's after-sale service unless you provide the original engraving or cutting files, engraving software
configuration parameters used, operating system information, video of the engraving or cutting process, and operational steps prior
to the occurrence of a problem or failure.
AtomStack is not liable for any and all losses arising from the user's failure to use the product in accordance with this manual.
Atomstack has the ultimate right to interpret the document, subject to legal compliance. Atomstack reserves the right to update,
modify, or terminate the Terms without prior notice.
03
Part 3 : Accessories list
Laser module Motherboard cable Fixed slider Power Adapter power cable
5PIN to 4PIN conversion cable M5*10screws M5 flat gasket H3 Allen key
04
Part 4 : Installation method
Remove the original laser and laser fixed slider
Remove the original laser and laser fixed slider The fixed slider of M150 module is a dovetail slider. If the original machine slider is
also a dovetail slider, the M150 module can be directly installed and used;
12replace slider
If the machine is as shown in the figure below, please install the dovetail slider
05
Part 4 : Installation method
Replace the dovetail slider in the accessories and fix it with M5*10+M5 gasket
3
06
5pin to 4pin conversion cable
For users who want to use the previous laser module
after replacing the cable, we have provided a conver-
sion cable, please choose according to your needs
Part 4 : Installation method
If the machine is as shown in the figure below,
there is no need to install the dovetail slider
07
Part 5 : Wiring method
Note: The driving current of M150 module is relatively large,
you need to use the equipped motherboard cable
08
The laser dower of this machine is very hiah. if you need to cut wood and other fammable materials with a power of more than
70%, please ensure someone is watching the machine in case of the flammable materials catches fire.
A lot of smoke is qenerated in engraving or cutting wood and other obiects.be
aware of cleaning the air quide hood and anti-skid cover,since there may be a
lot of dust accumulation on itespecially working with more than 50% of the
laser power.
Remove the shield if you couldor tum on the air assit while machine working,all
of which would significantly reduce dust accumulation.
！
09
Inhaltsverzeichnis
Sprachen:
Andere ATOMSTACK Steuereinheit Handbücher
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
