ATOMSTACK A6 PRO Bedienungsanleitung
A6\A12\A24 PRO Display Screen
User Manual
English
Deutsch
Français
Note: The pictures are for reference only, and the actual product shall prevail.
Please scan the QR code for more information.
F03-0238-0AA1
1.Product specications and working environment
2. Oine Basic Function Introduction
3. System language setting
4. Tilt detection
5. Flame detection
6. Autofocus
7. Touch Screen Button Sound
8. Resume engraving
9.Auxilia positioning
10.About
1
2
3
4
4
5
8
9
11
12
Directo
1.Product specications and working environment
1
Display Color 262K colors
Dimensions 4.3 inch
Resolution 480*272
TP Type RTP
Operating temperature “-10℃ ~ 60℃”
Storage temperature “20℃ ~ 70℃ ”
Operating humidity 10% ~ 90%RH, typical
value of 60% RH
2.Oine Basic Function Introduction
2.1 Home page introduction
The home page is mainly divided into two modules, the Engraving module
(1) and Set up module (2).
2.2.1 Clicking on the Engraver button on the home page will take you to
the le selection page
2.2.2 Return to the Home page/Back button
2.2.3 WiFi Name
2.2.4 Previous Page
2.2.5 Next Page
2.3 Select any le and click to enter the
pre-engraving page
2.2 Engraving
1) Engraving le name
2) Engraving button
3) Autofocus button
4) Frame: After clicking this button, the laser will peorm edge detec-
tion based on the size of the engraving pattern.
5) Move to center point: Click this button to make the laser move to the
center point of the engraving pattern.
6) Set as bottom left: Click this button to set the current location as the
bottom-left point of the pattern.
7) Set as center point: Click this button to set the current location as the
center point of the pattern.
8.9.10.11) Move up, down, left and right respectively.
12) Home: Regardless of the laser's current position, the laser will return
to the machine's original position.
1
1
2
2 3
4 5
Engraver 12345
12345.gc
1
23
4
5
6
7
8
9
10
11 12
2
1%
2.Oine Basic Function Introduction
3. System language setting
2.4 Click the engraving button to enter the engraving page
1)Display the name of the engraving le and the percentage of completion
2)Pause button
3)Stop engraving button
4)Adjust the step size for power coecient and speed coecient
5)Power coecient adjustment and display area
6)Speed coecient adjustment and display area
In the settings page, select system language. This version suppos Chinese, English, French, German, Italian, Spanish, and Russian.
1
3 4
5
6
2
3
4. Tilt Detection
5. Flame Detection
Operation method:
4.1 Click to enable the function. When the machine tilts at an angle between 15° and 20° with the hori-
zontal plane, the function is triggered: the machine automatically stops working, the buzzer sounds, and
if there is a display screen, it displays "Machine tilted". If there is no display screen, an alarm prompts on
the PC end.
4.2 There are 3 modes to deactivate the alarm:
4.2.1 No display screen: When the machine returns to a at position, the alarm automatically deactivated.
4.2.2 With display screen: Click "Close" on the display screen to deactivate the alarm.
4.2.3 APP: Prompts "Machine tilted",Click on the phone to close in the prompt box.
(This function is only available on machines with autofocus accessories)
5.1 Precautions:
5.1.1 When using outdoors, direct sunlight may cause false triggering of the function. It is recommended to use indoors.
5.1.2 To turn on/o the ame detection function, control it through the display screen/APP.
5.1.3 When cutting density boards, the ame detection function needs to be turned o to avoid false alarms.
5.2 Operation method:
5.2.1 Click to enable the function. When a re occurs directly below the laser, the function is triggered: the laser automatically returns to the origin of the
machine, buzzer sounds, and the display screen shows "Fire". If there is no display screen, an alarm prompts on the PC end and the buzzer keeps sounding. If
using the APP, it prompts "Flame detected".
5.2.2 The machine can be used normally after turning o and restaing.
4
6. Autofocus
(This function is only available on machines with autofocus accessories)
6.1 Precautions:
6.1.1 When using a chuck or a roller, or when engraving/cutting irregular objects (such as pebbles) or soft materials (such as oce paper, kraft paper,
cashmere fabric, denim), it is recommended to use a xed-focus tool for manual focusing. �
6.1.2 After the lower limit autofocus fails, the Z-axis automatically rises a ceain distance.
6.2 Operation method:
6.2.1 Manually or using Lightburn to move the Z-axis position (pay attention not to slide the Z-axis slider to the bottom). Refer to the diagram below for
controlling Z-axis movement in Lightburn.
6.2.2 After aligning the bottom of the laser with the object to be tested, x it in place. If there is a prompt indicating that the maximum range has been
exceeded, click "close". If the prompt continues to appear, slightly raise the laser.
The machine exceeds the maximum range of motion
5
6. Autofocus
6.2.3 Oine mode:
Open the "Autofocus" function on the display screen, then select the program to be engraved, click "Focus" to peorm automatic focus.After nding the upper
limit and the lower limit at the current position, the laser automatically lifts to the xed focal distance.Then click "Sta" to sta engraving.
6.2.4 Lightburn Automatic Focus Control:
a) Open Lightburn and locate the console, right-click on "Macro 0"
to open a window.
b) Enter [ESP500] in "Macro Contents" and click OK to
complete the setup.
12345.gc
6
1
2
1
2
6. Autofocus
6.2.5 LaserGRBL Automatic Focus Control:
a) In the toolbar below, right-click on a blank area to open the "Add
Custom Button" window. Click on "Add Custom Button".
b) Enter [ESP500] in "GCode" and enter the button name in "Caption" and
"Tooltip" to customize the button image on the left side. Click "Save" to
generate a custom button with the corresponding function.
6.2.6 How to use Auto Focus function in Lightburn and LaserGRBL:
Move the focus to the top of the engraving object and click the "Auto Focus" button to sta the automatic focus according to the settings.
7
6. Autofocus
7. Touch Screen Button Sound:
Notes:
1) If automatic focus is not needed, delete the GCode contents.
2) If a dialog box like the one in the image below appears during the automatic focus process, click OK to proceed.
7. Touch Screen Button Sound:
Enabling this function will produce button sounds when operating the control board.
8
Andere Handbücher für A6 PRO
1
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Sprachen:
