Atrump A1-3T Bedienungsanleitung
1
A Series
CNC BED MILL
OPERATION
MANUAL
2
TABLE CONTENT
Page
3
Introduction
CH
A
PTER
1
Safety Precautions
---
-
---------
--------------
4
1.1 Regulations
---
-
---------
--------------
5
1.2 Safety Warning
---
-
---------
--------------
7
1.3
Moving
Instructions
---
-
---------
--------------
8
CHAPTER 2
Machine Specification
---
-
---------
--------------
9
2.1 Machine Dimension
---
-
---------
--------------
9
2.2 Main Parts Of Machine
---
-
---------
--------------
13
2.3 Machine Travels
---
-
---------
--------------
14
CHAPTER 3
Installation
---
-
---------
--------------
18
3.1
Precaution
---
-
---------
--------------
18
3.2
Machine Unwrapped
---
-
---------
--------------
18
3.3
Workplace Environment Factors
---
-
---------
--------------
19
3.4 Machine Leveling
---
-
---------
--------------
23
3.5 Power Installation
---
-
---------
--------------
24
Chapter 4 Maintenance
---
-
---------
--------------
25
4.1 Maintenance Schedule
---
-
---------
--------------
25
4.2
Lubr
icator system
---
-
---------
--------------
27
Chapter 5 Trouble Shooting
---
-
---------
--------------
28
5.1 Introduction&Precaution
---
-
---------
--------------
28
5.2
Machine Diagnosis
---
-
---------
--------------
29
5.3
Survey of the problems
---
-
---------
--------------
30
5.4
Help & Support
---
-
---------
--------------
31
5.5
Other Problems
---
-
---------
--------------
32
Appendix
Mill Head Operation Instruction (for 3T/5T model)
---
-
---------
--------------
34
3
Introduction
1、Before installing and operating your machine please read the manual
in detail.
2、This manual will teach you the installation, operation and basic
maintenance of the machine. It teaches you how to operate this machine
safelyand correctly.
3、It’s very important to understandeach label and machine warning label in
this manual.
4、About the programming, please read the introduction of controller
programming.
5
、About the operation of CNC control panel, setting up parameter and function,
please read the introduction of controller operation.
6. Please don't discard this manual, if lost please contact us for a replacement.
4
CHAPTER 1
Safety Precautions
＊＊THIS MACHINE MUST NOT BE SERVICED, REPAIRED OR MAINTAINED BY
UNQUALIFIEDAND UNTRAINED PERSONNEL. ＊＊
This machine is equipped with a number of safety devices to protect personnel and
equipmentfrom injury and damage. Operatorsshould not, however,rely solely
upon these safety devices but should operate the machine after fully
understandingthe following paragraphs.
Moreover, improper operation and maintenance of any CNC machine increases the
likelihoodof serious personalinjuryand greatly reduces theservice life of this
machine.Yourattention to this manual,in combinationwith commonsense and good
machining practice, can positively affect productivitybyreducing downtime and
promotingsafe operation of this machine unless they are explicitlystated in this
instructionmanual.
Additionalsafetyconsiderations may be required for your particularapplication.
Please refer to safety informationfor additional informationand reference
publications.
5
1.1 Regulation：
1. Only qualified personnel are permitted to maintain and operate this machine.
2. Do not operate or attempt to repair the machine until you have read and
understood all manuals that pertain to the machine, plus all warning and
instructionplates/decals mountedon the machine.
3. Be mentally alert on the job and keepsafety in mind. Never attempt to operate
or repair a machine if you are under medicationor alcohol influence.
4. Wear safetyshoes and eye protection within the work area. Safety shoes should
be oil-resistant and safety glasses with side shields are stronglyrecommended.
5. Remove watches, jewelry andother accessoriesto avoid getting them caught in
movingparts.
6. Maintaina clean and orderly workspace around machine.
7. Store tools and miscellaneousparts properly. Be sure there are on articles
aroundthe machine.
8. Do not use compressed airs to blow chips form the machine spindle or table,
controls,cabinets,or the floor around the machine. Use a brush or chip scraper to
remove chips. Donot remove chips by handor while thespindle is turning. Make
sure that the cutter has completelystopped before attempting to remove chips.
Dispose of chips frequently.
09. Never start the machine when the cutter is in contact with the workplace. Make
sure the direction of spindle rotation is correct to prevent cutter breakage.
10. Know where all the EMERGENCYSTOP push buttons are located. Keep all
machine doors closed while the machine is in operation,including those on the
console and the electrical cabinets.
11. In the event of power failure, turn off main circuit breaker immediately.
6
12. Do not start the machine unless all units contain the proper amount and type of
hydraulic oils, lubricant or acceptable equivalents.
13. Fuses replacement should have the proper current ratings.
14. Do not change parameters, volumes and other electrical setting unnecessarily. If
such changes are unavoidable,record the values prior to any adjustments for future
reference.
15. Do not soil, scratch or remove the caution plate. Should it become illegible to
reador missing,order anothercaution plate form the supplier.
16. Wheneveroperating a forklift truck, crane or similar equipment,special care
should be taken to prevent collisions and damage to surroundings.
17. Do not leave machine unattended, but stand away while it is running.
18. Turnoff the powersource before leavingforthe day.
7
1.2 SafetyWarning
Be sure your installation conforms to applicable electrical codes. Inspect all electrical
connections before installing, operating or servicing machine. Be sure power supply
voltage matches machine voltage.
Disconnect all power to the machine before installing or servicing machine. Disconnect
all power before opening electrical or control box. Service should be only performed
by a qualified engineer.
8
1.3 MovingInstructions
1. Make sure when moving the machine that you have a support block from the
working table to the mill head, because the spindle head may shake while moving.
2. When transporting the machine using a crane or forklift make sure you have a
trained/certified personnel operating the forklift/crane. Make sure to move the
machine slowly and keep it balanced to avoid damage to machine or collision.
9
CHAPTER 2
Machine Specification
2.1 MachineDimension
10
Dieses Handbuch passt für folgende Modelle
4
Inhaltsverzeichnis
Andere Atrump Elektrowerkzeuge Handbücher
