ATS 31 Series Bedienungsanleitung

FURNACE

Model Number: 31XX, 32XX

INSTRUCTION MANUAL

This manual contains important operating and safety information. Carefully read and

understand the contents of this manual prior to the operation of this equipment.

www.atspa.com

Applied Test Systems

REVISED MAY 2017

Information in this document is subject to change without notice and does not represent a

commitment on the part of Applied Test Systems (ATS).

For assistance with set-up or operation, contact the ATS service department. Please have this

manual and product serial number available when you call.

Telephone: +1-724-283-1212.

www.atspa.com i

MANUAL CONTENTS

A. Safety........................................................................................................................ 1

A.1 Owners, Operators, and Maintenance.......................................................................1

A.2 Environmental Conditions........................................................................................

B. Introduction.............................................................................................................. 5

B.1 Unpacking............................................................................................................5

B.2 After Sale Support.................................................................................................5

C. Installation................................................................................................................ 6

C.1 General Installation ...............................................................................................6

C.2 Positioning and Connecting.....................................................................................6

D. Pre-Operation Instructions ..................................................................................... 8

D.1 Furnace Bake-Out .................................................................................................8

E. Temperature Controller ........................................................................................... 9

E.1 Temperature Controller Overview.............................................................................9

E.2 Temperature Controller Installation ..........................................................................9

E.3 Temperature Controller Operation ......................................................................... 10

E.4 Over-Temperature Option ..................................................................................... 10

F. Furnace Operation ................................................................................................. 12

G. Furnace and Element Maintenance ..................................................................... 13

G.1 Preventative Maintenance .................................................................................... 13

ii Applied Test Systems

G.2 Embedding & Patching Element............................................................................. 13

G.3 Element Replacement .......................................................................................... 14

3110 Tube Furnace Element Replacement ............................................................... 14

3210 Split Tube Furnace Element Replacement ........................................................ 16

3150/3160 Box Furnace Element Replacement......................................................... 18

Removing Side Elements – 3150 and 3160 .......................................................... 18

Removing Bottom Elements – 3150 ................................................................... 19

Removing Side Elements – 3160 ....................................................................... 19

Removing Rear Elements – 3160 ....................................................................... 19

Replacement and Reassembly ........................................................................... 19

H. Temperature Controller Maintenance .................................................................. 21

H.1 Preventative Maintenance .................................................................................... 21

I. Troubleshooting ...................................................................................................... 22

I.1 Controller Does Not Operate.................................................................................. 22

I.2 Over-Temperature................................................................................................ 23

I.3 Under-Temperature .............................................................................................. 24

APPENDIX A: Safety Data Sheet Information .......................................................... 25

APPENDIX B: Warranty.............................................................................................. 46

Series 31XX, 32XX Furnaces | A. Safety 1

A. Safety

A.1 Owners, Operators, and Maintenance

This manual uses note, caution, and warning symbols throughout to draw your attention

to important operational and safety information.

Read and understand all instructions and safety precautions listed in this manual before

installing or operating your unit. If you have any questions regarding operation of the unit

or instructions in this manual, contact our Service Engineering Department at +1-724-

283-1212.

In addition to the safety warnings listed here, warnings are posted throughout the

manual. Read and follow these important instructions. Failure to observe these

instructions can result in permanent damage to the unit, signicant property damage,

personal injury, or death.

Read and understand all instructions and safety precautions listed in this

manual before installing or operating your unit. If you have any questions

regarding operation of the unit or instructions in this manual, contact our

Service Engineering Department.

Thoroughly understand the safety features and operation of the

equipment. This manual will provide operators with safety concerns and

general procedures. Be familiar with correct operating principles and

use good judgment. Also refer to the appropriate manuals for system

component safety instruction manuals.

Use caution when working with elements at elevated temperatures.

Prevent burns by wearing protective clothing, and follow safety, operation,

and maintenance procedures described in the appropriate instruction

manuals.

Avoid radiating heat. Items with a large mass retain heat for a long time.

First-degree burns may occur from heat radiation as well as from direct

contact with a hot surface.

Obey all national and local electric code requirements. Furnaces and

control systems must be grounded and wired according to national and

2Series 31XX, 32XX Furnaces | A. Safety

local electrical code requirements.

Handle the furnace carefully. Avoid dropping and jarring the furnace.

Avoid damage to cables. Do not let the power cables touch the heated

furnace shell.

Do not exceed maximum operating temperature. Operate the furnace

and accessories within the appropriate temperature range. Refer to the

appropriate manuals.

Dangerous high voltages present. Do not attempt to open the enclosure

or gain access to areas where you are not instructed to do so. Refer

servicing to qualied service personnel only.

Caution - Injury to the operator could occur if operational procedures are

not followed. Follow all steps or procedures as instructed and refer to

accompanying documents.

Ventilation – Slots and openings in the cabinet are provided for ventilation

and to ensure reliable operation of the product. To protect the unit from

overheating, those openings must not be blocked or covered. This product

should not be placed in a built-in installation, such as a wall cut-out unless

proper ventilation is provided. Hot temperatures will result.

Refer to manual. Before tuning the temperature controller, be sure to read

and understand the tuning instructions in the controller manual. Follow all

operating and other instructions carefully.

If it should become necessary to clean this equipment, disconnect the unit

from its power source rst. Do not use liquid cleaners, aerosols, abrasive

pads, scouring powders or solvents, such as benzene or alcohol. Use a

soft cloth lightly moistened with a mild detergent solution. Ensure the

surface cleaned is fully dry before reconnecting power.

Do not attempt to operate the temperature control system in ambient

temperatures higher then 120° F (49° C) without providing a cooling fan

or air conditioning.

Do not use a temperature control system with a power output rating lower

than the current rating of the furnace.

Use the same thermocouples as indicated on the setpoint controller.

Other types will result in faulty control which may cause damage from

overheated components.

When changing fuses in current limiting power controllers, use only the

fuse type and size specied by the power controller manufacturer.

Use interconnecting cables of the proper gauge to match the ratings on

the data labels for the furnace and controller.

Do not connect any measuring or controlling devices to the thermocouple

other than the main temperature controller.

Use thermocouple extension wires and connectors that match the

thermocouple type being used. Use of copper wires will cause errors in

readings and result in faulty control.

Do not allow the bare thermocouple wires or any part of the thermocouple

to come in contact with other metals. This could induce incorrect voltages

and result in erroneous readings and faulty control.

A.2 Environmental Conditions

The furnace is meant for use in laboratory/factory settings in a dry, clean work

environment. There should be a clean and sturdy work surface both at a reasonable

working height and away from any water, gas, or electrical hazards. The work surface

should be able to support more than the weight of the unit itself. The indoor area should

be well ventilated and containing no open ames or materials that may constitute a re

hazard.

• Temperature of 15° C to 35° C

• Relative humidity not more than 75%

• Air pressure of 75 kPa to 106 kPa

• No hard-frost, dew, percolating water rain, solar irradiation, etc.

Series 31XX, 32XX Furnaces | A. Safety 3

4Series 31XX, 32XX Furnaces | A. Safety

• Installation category II

• Pollution degree 2

Series 31XX, 32XX Furnaces | B. Introduction 5

B. Introduction

B.1 Unpacking

Retain all cartons and packaging materials until the unit is operated and found to be in

good condition. If damage has occurred during shipping, notify Applied Test Systems

and the carrier immediately. If it is necessary to le a damage claim, retain the packing

materials for inspection by the carrier.

B.2 After Sale Support

When you receive your equipment, copy your data label information onto the data

label template below (Figure B.1). Doing this will ensure you will have the appropriate

information for your records.

If you have any questions concerning the operation of your unit, contact your sales

representative. Before calling, please obtain the serial number from the unit’s data label.

Also, please be prepared to give a complete description of your problem.

Figure B.1 - Sample ATS data tag

6Series 31XX, 32XX Furnaces | C. Installation

C. Installation

C.1 General Installation

This section describes how to prepare your Applied Test Systems (ATS) furnace for

operation. Only perform the steps that apply to your specic furnace type. The installation

of the equipment must be performed by a qualied and licensed electrician in accordance

with National Electric code and local codes.

C.2 Positioning and Connecting

The following procedure describes how to position and connect an ATS Furnace that

is equipped with leg levelers. For furnaces that are mounted to a test machine or are

mounted using a test bracket, refer to appropriate mounting drawings.

1. Carefully remove the shipping crate and packing materials. Do not discard the packing

materials until all items on the invoice have been accounted for.

2. Position the furnace in the desired location.

3. If the unit did not come with a control system, skip to step 8 (p. 7).

4. The control system may or may not have a power cord supplied. If it does not, remove

the top cover of the control system to locate the power supply connection. To do this,

remove the two screws at the top of the back of the unit and slide the cover o toward

the back side. See Figure C.1 for screw location.

NOTE: Figure C.1 shows a typical control system. Not all control systems

will appear exactly the same.

Figure C.1 - Typical Control System (Back)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ATS Ofen Handbücher

ATS

ATS 3210 Bedienungsanleitung

Beliebte Ofen Handbücher anderer Marken

Armstrong

Armstrong EG7H SERIES Bedienungsanleitung

Payne

Payne PG92ESA Leitfaden

SUPREME

SUPREME FEM10-M2301CM-A Montageanleitung

Ingersoll-Rand

Ingersoll-Rand S9V2B080D4VSAC/D Montageanleitung

Johnson Controls

Johnson Controls TM9T Leitfaden

Fluke

Fluke 9118A Bedienungsanleitung

Lennox

Lennox EL195UHE Elite Series Installations- und Betriebshandbuch

Intertherm

Intertherm M7RL Series Bedienungsanleitung

HDG

HDG Pelletmaster 15 Bedienungsanleitung

Pinnacle

Pinnacle Aero Bella AB-716C-QH Handbuch

Nortek

Nortek MG2S Series Bedienungsanleitung

VERDER

VERDER CARBOLITE GERO ABF 8/28 Handbuch

Goodman

Goodman GMV9 Handbuch

SUPREME

SUPREME SUP10-M2301C Montageanleitung

Dettson

Dettson AMT400B34-SM1PMA Montageanleitung

Evcon

Evcon DGD 60 MBH Bedienungsanleitung

Trane

Trane S8B1A026M2PSAB Montageanleitung

Hart Sceintific

Hart Sceintific 9113 Bedienungsanleitung