ATS TTV1EEM-3T Bedienungsanleitung

Aqua Treatment Service

194 Hempt Road

Mechanicsburg, PA 17050

www.aquat.com

Installation, Operation and

Maintenance Manual

CAUTION: Read and Follow all safety rules and

operating instructions before first use of product.

DEALER NAME:

DEALER PHONE #:

MODEL #:

SERIAL #:

DATE INSTALLED:

Revised 01/17/13

TTV Series

Softening Water System

Installation Instructions:

General ........................................................................................................... 2

Installation Diagram ........................................................................................ 3

Control Valve:

Front Cover and Drive Assembly .................................................................... 4

Regeneration and Error Screens,

Button Operations and Functions ....................................................... 5

User Displays ................................................................................................. 6

Configuration Settings .................................................................................... 7 - 9

Setting Regeneration Cycle Times ................................................................. 10

Installer Display Settings ................................................................................ 11 - 12

Diagnostics ..................................................................................................... 13

Parts Breakdown:

System ............................................................................................................ 14

Control Valve ................................................................................................... 15 - 23

Specifications: .................................................................................................................. 24

Troubleshooting: .............................................................................................................. 25 - 28

Warranty: ............................................................................................................................ 29

Table of Contents

Softener Settings

Gallons until Regeneration

Water Hardness

Backwash Minutes

Brine Draw Minutes

2nd Backwash

Rapid Rinse

Brine Tank Fill

Model #

Capacity per Unit

4. Drain Line Connection

• Thread taped drain fitting into by-pass drainport.

• Connect ½" I.D. plastic tubing to drain fitting with clip.

• Do not exceed 6ft. elevation or 20ft. Run to drain.

• Leaving 1½" air gap run drain to floor drain, laundry tray or

septic/sewer line with trap.

5. Brine Line Connection

• Install air check on threaded connection.

• Run tubing from compression fitting on air check to compression

fitting on brine tank.

6. Overflow Line Connection

• Attach length of ½-inch (1.3) I.D. tubing (not supplied) to fitting

and run to drain. Do not elevate overflow line higher than 3 inches

(7.6cm) below bottom of overflow fitting. Do not tie drain line of

the equipment control. Overflow line must be a direct, separate

line from overflow fitting to drain. Allow an air gap as per drain

line instructions.

7. Electrical Connection

• Remove twist tie from cord set and extend cord to its full length.

Plug into socket that will accept 3-prong. Be sure the electrical outlet

is not controlled by a wall switch. Set timer to current time of day.

Pre Installation Check List

Water Pressure —A minimum of 30 psi is required for regenerated of

the unit. If the water pressure is over 100 psi, a pressure reducing valve

must be installed before the equipment and set at 85 psi

Electrical —A grounded electrical outlet with a continuous supply of

110 to 120 volt - 60 hertz current should be located at installation site of

the equipment.

A drain, must be available within 20 feet of the equipment.

Location of the equipment must be where it is not subject of freezing,

direct sunlight or room Temperature over 120°F.

A minimum of 4 gallons per minute must be available for proper

backwash/regeneration.

The equipment must be installed in the cold water line after the well pres-

sure tank or water meter and before it branches off to the

water heater.

Installation

1. All plumbing must conform to local codes

2. Location Selection

• If it is likely that supplementary water treatment equipment will be

required, make certain adequate additional space is available.

• Since salt must be added periodically to the equipment, the location

should be easily accessible.

• Do not install any equipment closer to a water heater than a total

run of 10 feet of piping between the outlet of the equipment and the

inlet to the heater.

3. Water Line Connection

• A by-pass valve system must be installed since there will be

occasions when the equipment must be by-passed for raw water or

for servicing.

• Temporarily attach by-pass to back of control valve.

• Close main water supply valve.

• Open faucets to relieve water pressure and drain system.

• Move the equipment into installation position.

• After taking all measurements for required piping, disconnect

by-pass from control and move the equipment to a safe location.

• Cut, fit and solder plumbing.

• Solder plumbing to by-pass valve, raw water line to inlet, house line

to outlet.

• Move equipment back into position and connect by-pass valve.

• Fill brine tank with Solar Salt.

General Installation Instructions

Installation Diagram

WARNING

Follow ALL Local Building Codes

when installing systems

Sanitary Sewer Line

Cold Water Inlet

Cold Water Outlet

Valve Control

Clean Water

Tank Assembly

System

Drain

Line

Floor Drain

Hard Water Line to

Unsoftened Fixtures

Direction of water flow

Brine Tank Line

Brine Tank Assembly

Brine Tank Overflow

Drain Line: .5” I.D. is Min Size

To approved air gap drain.

Drawing No. Order No. Description Quantity

1 V3175EE-01 WS1EE FRONT COVER ASSEMBLY 1

2 V3107-01 WS1 MOTOR 1

3 V3106-01 WS1 DRIVE BRACKET & SPRING CLIP 1

4 V3408EE-02BOARD WS1THRU2L EEPCBRD MAV/ALT REPL 1

5 V3110 WS1 DRIVE GEAR 12X36 3

6 V3109 WS1 DRIVE GEAR COVER 1

Not Shown V3186 WS1 AC ADAPTER 110V-12V 1

V3186-01 WS1 AC ADAPTER CORD ONLY

Not Shown V3178 WS1 Drive Back Plate 1

EE Front Cover and Drive Assembly

AC Adapter U.S. International

Supply Voltage 120 V AC 230V AC

Supply Frequency 60 Hz 50 Hz

Output Voltage 12 V AC 12 V AC

Output Current 500 mA 500 mA

Battery replacement is

3 volt lithium coin cell

type 2032.

Correct

Battery

Orienta-

tion

Battery Fully Seated

When replacing the battery, align

positives and push down to fully seat.

Refer to Control Valve Service Manual for other drawings and part numbers.

Control Valve

Regen Screen

Displays the time remaining in the current cycle.

Pressing REGEN advances to the next cycle.

Error Screen

#+)%+3* !%))%))&)&-)0

seconds. Clear by dissconnecting the power supply at

the PC board and reconneting, or press the NEXT and

,++&%**!$,+%&,*#0&)*&%*

Regeneration and Error Screens

Button Operation and Function

Scrolls to the next display.

Changes variable being displayed.

Key sequence to lock and unlock program settings.

&#!%&)*&%*!%!+!+*&%+)&#)*+ *&+.)-)*!&%!*!*'#0%+ '!*+&%)+,)%*+&

the home/service position, resynchronizing the valve.

Pressing once and releasing will schedule a regeneration at the preset delayed regeneration time.

Pressing again and releasing will cancel the regeneration.

)**!%% &#!%&)*&%*.!##!%!+!+%!$$!+)%)+!&%

Pressing while in regeneration will advance to the next cycle.

Pressing in the program levels will go backwards to the previous screen

Cycle Range of times (min.)

1. Backwash 1st ,'3&.

%)%+).#&.!%*&.%3&.

".* nd ,'3&.

*+!%*&.%3&.

%)%+2##.!+ +)+.+)

)-!&.%3&.

1 - 20

1 - 99

1 - 20

0.1 - 99.9 or OFF

Regeneration Cycles and Times

The user can initiate manual regeneration. The user has the option to request the manual regeneration at the delayed regeneration

time or to have the regeneration occur immediately:

1. Pressing and releasing the REGEN button. 1.!##3* +&.)*%&%+ !*'#0%+ )%)+!&%.!##&,)++ 

delayed regeneration time. The user can cancel the request by pressing and releasing the REGEN button.

 )**!%% &#!%+ ,++&%&)'')&/!$+#0*&%*.!##!$$!+#0*+)++ )%)+!&% ,*)%%&+

%#+ !*)(,*+/'+0)*++!%+ &%+)&#0')**!%%,++&%**!$,#+%&,*#0&)*&%*

Control Valve cont:

User 1

Typical user display. If volume is selected in Conguration

Settings Step 3CS, shows volume remaining to regeneration. If

volume is not selected in Conguration Settings Step 3CS, this

screen will not be shown. If a meter is not used this display will

not change.

User 2

Displays number of days to next regeneration.

User 3

Displays ow rate in gallons per minute. If a meter is not used

this display will be shown but 0 will be displayed.

This screen will not be shown if 7 day or 28 day is selected in

Conguration Settings Step 3CS.

User 4

Displays total ow in gallons since last reset. If a meter is

not used this display will be shown but 0 will be displayed.

This screen will not be shown if 7 day or 28 day is selected in

Conguration Settings Step 3CS.

PRESS THE DOWN WARROW

FOR 3 SECONDS TO RESET TO 0.

User 5

Shows current time.

Setting Time of Day

Push NEXT button until time of day screen is displayed. Press and

hold the VorWarrow until the SET indicator is displayed, and

the hour ashes. Press the Vor Wbutton until the correct hour is

displayed.

Then press the NEXT button. The minutes will ash. Press the

Vor Warrow until the correct minute is displayed.

Press the NEXT button to return to the Display Screens. Time of

day should only need to be set after power outages lasting more

than 8 hours, if the battery has been depleted and a power outage

occurs, or when daylight saving time begins or ends. If a power

outage lasting more than 8 hours occurs, the time of day will ash

on and off which indicates the time of day should be reset. If a

power outage lasts less than 8 hours and the time of day ashes on

and off, the time of day should be reset and the battery replaced.

User Displays

General Operation When the system is operating, one of ve displays may be shown.

Pressing NEXT will alternate between the displays shown below.

Control Valve cont:

Conguration Settings

Step 1CS – Press Vand Wbuttons simultaneously for 5 seconds and release. If screen in Step 2CS does not

appear, the lock on the valve is activated. To unlock press W, NEXT, REGEN, Vin sequence, then press V

and Wbuttons simultaneously for 5 seconds and release.

Step 2CS – Choose 1.0 for 1”, 1.25 for 1.25”, 1.5 for 1.5”, 2.0L for 2L, 2.0 for 2” valve ¹. Press NEXT to go

to Step 3CS. Press REGEN to exit Conguration Settings.

Note: When using the WS2 valve, if “2L” is set instead on “2.0” for valve type, when the valve is in

regeneration and the piston drives to the “Draw” cycle the piston will stall and generate a 1002 error code.

Clear error code by pressing “NEXT” and “REGEN” simultaneously until the valve resets, then re-program

to proper valve type setting.

Step 4CS – Press the Vor Wbuttons to select to regenerate immediately on 0 or at delayed time.

Immediately on 0 can only be selected if Volume (gallons) was selected in step 3CS and a meter must be

installed. Delay is the only option for the other Step 3CS selections. Press NEXT to go to Step 5CS. Press

REGEN to return to previous step.

Step 1CS

Step 2CS

Step 3CS – Press the Vor Wbuttons to select one of the following:

• If Volume (gallons) is selected the regeneration will occur after the specic volume has been used or on the

day override (if selected) whichever comes rst.

• If 28/Volume (gallons) is selected the regeneration will occur on the day (1 through 28) selected in Installer

Display Settings. If a meter is not used the total ow and ow rate user displays and the volume display in

Diagnostics will be shown as 0.

• If 7/Volume (gallons) is selected the regeneration will occur on the selected day(s) of the week (see

instructions contained in Installer Display Settings). If a meter is not used the total ow and ow rate user

displays and the volume display in Diagnostics will be shown as 0.

• If 28 is selected the regeneration will occur on the day (1 through 28) selected in Installer Display Settings.

The total ow and ow rate user displays and the volume display in Diagnostics will not be shown even if a

meter is used.

• If 7 is selected the regeneration will occur on the selected day(s) of the week (see instructions contained in

Installer Display Settings). The total ow and ow rate user displays and the volume display in Diagnostics

will not be shown even if a meter is used.

Press NEXT to go to Step 4CS. Press REGEN to return to previous step.

Step 4CS

¹ When using the WS2 control valve, the circuit board software must have meter selection choices

of 2.0 and 2.0L. The WS2 valve must be set for the 2.0 meter selection during programming. If the

software version does not have both the 2.0 and 2.0L selections, consult your equipment supplier

for a replacement circuit board. When using the WS2L valve with older version software that does

not have both 2.0 and 2.0L selection choices, the valve must be set to 2.0 during programming. If a

WS2L valve is being used with newer version software that has both 2.0 and 2.0L selection choices,

the valve must be set to 2.0L during programming.

Step 3CS

Control Valve cont:

Step 5CS – - Allows selection of one of the following

using the Vor Wbuttons:

• the Control Valve to have no hard water bypass;

• the Control Valve to act as an alternator; or

• the Control Valve to have a separate source during the

regeneration cycle.

Select OFF when none of these features are used.

Only use Clack No Hard Water Bypass Valves or

Clack Motorized Alternating Valves (MAV) with these

selections. Clack No Hard Water Bypass Valves (1” or 1.25” V3070FF or V3070FM) are not designed to be used with the alternator or separate

source functions. The V3063 and V3063BSPT motorized alternating valves are not designed to be used as a no hard water bypass or separate

source inlet if the pressure differential is more than 60 psi.

Conguring the Control Valve for No Hard Water Bypass Operation:

Select nHbP for control operation. For no hard water bypass operation the three wire connector is not used.

Selection requires that a connection to MAV or a Clack No Hard Water Bypass Valve is made to the two pin connector labeled ALTERNATOR

DRIVE located on the printed circuit board. If using a MAV, the A port of the MAV must be plugged and the valve outlet connected to the B

port. When set to nHbP the MAV will be driven closed before the rst regeneration cycle that is not FILL or SOFTENING or FILTERING, and

be driven open after the last regeneration cycle that is not FILL.

NOTE: If the control valve enters into an error state during regeneration mode, the no hard water bypass valve will remain in its current state

until the error is corrected and reset.

Conguring the Control Valve for Separate Source Operation:

Select nHbP for control operation. For separate source operation the three wire connector is not used.

Selection requires that a connection to a Clack Motorized Alternator Valve (MAV) is made to the two pin connector labeled ALTERNATOR

DRIVE located on the printed circuit board. The C port of the MAV must be connected to the valve inlet and the A port connected to the separate

source used during regeneration. The B port must be connected to the feed water supply.

When set to nHbP the MAV will be driven closed before the rst regeneration cycle, and be driven open after the last regeneration cycle.

NOTE: If the control valve enters into an error state during regeneration mode, the MAV will remain in its current state until the error is

corrected and reset.

Selecting the Control Valve to act as an alternator:

Prior to starting the programming steps, connect the interconnect cable to each control valve board’s three pin connector labeled

“INTERCONNECT”. Also connect the meter cord to either control valve to the three pin connector labeled “METER”.

Valve Programming Steps

Conguration

Settings Step 3CS Select Volume Set Volume

Conguration

Settings Step 4CS Set regeneration time option to “On O”. Set regeneration time option to “On O”.

Conguration

Settings Step5CS

Set to ALTA

Connect ALTA valve to the MAV’s A

port and connect the MAV’s two pin wire

connector to the two pin connector labeled

“DRIVE” on the ALTA valve

Set to ALTb

Connect ALTb valve to the MAV’s B port. No

connections between the ALTB valve and the MAV

are made.

Installer Display

Setting Step 2I Enter the Volumetric Capacity for the System Enter the Volumetric Capacity for the System (the

same as Valve A)

Installer Display

Setting Step 3I Set Day Over ride to “oFF” Set Day Over ride to “oFF”

NOTE: If the control valve is in an error state during regeneration mode the MAV will close the B port and keep open the A port until the error is

corrected and reset.

For Clack Corporation alternator systems using the WS1, WS1.25, WS1.5 and WS2L valves the stand by tank will be periodically brought on

line for a short time to keep its bed fresh. The logic is that once a tank is in standby and the time has passed either 6 AM or 6 PM (18:00) at the

next and all subsequent 6 AM and 6 PM times the stand by tank will be brought on line until 10 gallons (37.8 liters) has passed through it. It

will then be placed back on standby.

For Clack Corporation alternator systems using the WS2 valve, when NEXT is pressed after selecting ALTA or ALTb, a display will allow the

user to set the amount of pre-service rinse time for the stand by tank just prior to returning to service.

Press NEXT to go to Step 6CS. Press REGEN to return to previous step.

Step 5CS

Volume Volume

Control Valve cont:

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ATS Wasserfiltersystem Handbücher

ATS

ATS DWS-8C Bedienungsanleitung

Beliebte Wasserfiltersystem Handbücher anderer Marken

Wisy

Wisy LineAir 100 Bedienungsanleitung

Schaffner

Schaffner Ecosine FN3446 Series Betriebsanleitung

Pentair

Pentair FLECK 4600 SXT Benutzerhandbuch

H2O International

H2O International H20-500 Bedienungsanleitung

Renkforce

Renkforce 2306241 Bedienungsanleitung

Neo-Pure

Neo-Pure TL3-A502 Bedienungsanleitung

FLTR

FLTR OBF Bedienungsanleitung

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Bedienungsanleitung

Applied Membranes

Applied Membranes W-G844EM Bedienungsanleitung

BEGA

BEGA 116 Bedienungsanleitung

WATA

WATA Standard Bedienungsanleitung

Price

Price FFU series Handbuch

Gaggenau

Gaggenau BRITA INTENZA 467873 Bedienungsanleitung

Brita

Brita SAFF-100 Bedienungsanleitung

HEISSNER

HEISSNER FPU24000-00 Bedienungsanleitung

BGS technic

BGS technic 1518 Bedienungsanleitung

Reverse Osmosis

Reverse Osmosis RF Series Bedienungsanleitung

ubbink

ubbink Filtramax Series Bedienungsanleitung