Auber PT100M Bedienungsanleitung

PT100M Installation Guide

Version 1.0

Auber Instruments, 730 Culworth Manor, Alpharetta, GA 30022

e-mail: [email protected] Tel: 404-291-6298

www.auberins.com

(This guide was extracted and modified from the Installation Guide for the PID Retrofitting

Kit for Rancilio Silvia. Full instruction will be provided to the kit buyer)

Procedure

Installation in boiler compartment

Fig 1, top view of original wiring. Red arrows indicate where the controller power cable

will be tapped. Green arrow points to brew water control thermostat. Blue arrow points

to steam temperature control thermostat.

1) There are two thermostats on top of the boiler. The one on the left with a red dot on top is

the brew water temperature control thermostat. The one on the right is for controlling the

steaming temperature. You need to remove the cable connectors on both side of brew

water temperature thermostat (connectors with red and gray cable). They need to be

connected to the output cable of SSR (after the RTD sensor installation). You also need

to remove this thermostat and move the steaming thermostat to its position. This is

because you need to mount the RTD sensor to the thermowell underneath the steam

temperature control thermostat. This thermowell is closer to the cold water inlet, and

results in better control. You need to use a small to medium sized flat head screw driver

to remove the screw. Be very careful to not let it drop into the gap below. A magnetized

screw driver will help. Fig 2 shows the steam thermostat has been relocated and

thermowell for RTD sensor is exposed (marked with red arrow).

Fig 2, Thermowell for RTD mounting

2) Install the RTD sensor. Caution: the connection between the RTD and cable is very

fragile because of the small size and there is no strain relieve. To prevent the sensor from

breaking, install the sensor without unwrapping the cable (install it as the way it was

received). This will reduce the twist pulling force when screwing on the sensor. The

sensor can be tightened with a small wrench or pliers. It does not need to be very tight. If

you want make sure the sensor didn’t get damaged during installation, you can measure

the resistance of the sensor after installation. It should be in the 100 to 140 ohm range.

3) Install the cable from SSR output to the gray and red connector. Fig 3 shows what it

should look like at this step.

Fig 3. Wiring for SSR output and RTD sensor. Red arrow points to RTD sensor. Green

arrows point to the SSR output connections. Blue arrow points to the steam thermostat.

Brew Water Temperature Setting Table 1.

Part Number Description SV value in ºC SV value in ºF

PT100M Rancilio Silvia 107 225

Table 1 lists default settings for the SV of the controller. Based on the discussions from forums,

the generally accepted setting for Silvia PID has been around 228-229 ºF for sensors mounted on

the top of boiler. The values in table 1 have been adjusted for the RTD sensor. We found the

temperature in the thermowell is about 2 ºC (3.5 ºF) lower than that on the top of the boiler after

the machine is equilibrated for 45 minutes or longer. Since SV can be easily changed, it will up

to the user to decide what the best temperature is for the espresso.

Recommend PID Parameters with PT100M sensor.

For the current model of SYL-1512, you can try the following setting.

SouF=1.0, P=3.0, I=100, D=40

SouF=1.0, P=3.3, I=183, D=45

SouF=1.0, P=4.0, I=200, D=50

Please note that these numbers only apply to RTD sensor. They are independent with the

temperature display unit. Either F or C will work.

Inhaltsverzeichnis

Andere Auber Controller Handbücher

Auber

Auber TD400P Bedienungsanleitung

Auber

Auber WS-1500FXL Administratorhandbuch

Auber

Auber SYL-23X2P Original Betriebsanleitung

Auber

Auber WS Series Administratorhandbuch

Auber

Auber RDK-300B Bedienungsanleitung

Auber

Auber Cube 4E Bedienungsanleitung

Auber

Auber SWA-2451A Bedienungsanleitung

Auber

Auber SYL-2342 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch