Audio Precision System Two Bedienungsanleitung
Audio Precision, Inc.
PO Box 2209
Beaverton, Oregon 97075-2209
U.S. Toll Free: 1-800-231-7350
Tel: (503) 627-0832 Fax: (503) 641-8906
email: [email protected]
Web: www.audioprecision.com
Audio Precision PN 8211.0034
March 1998
Rackmounting Instructions
for the Audio Precision System Two
Introduction
With the hardware included in this kit, the Audio Precision System Two can be rackmounted in two
ways: either using the slide-out rackmount adapters, or using the fixed rackmount adapters. Refer to
the appropriate instruction set on the following pages.
Parts List Audio Precision Part No.
1 Pair sliding rackmount assembly 7171.0001
1 Mounting hardware packet (comes with rackmount assembly)
6 Screws, 10-32 x 5/16” truss head (included in mounting hardware packet above)
2 Chassis Trak Mounting brackets 7310.0014
1 Rackmount front bracket, left hand 7170.0201
1 Rackmount front bracket, right hand 7170.0202
1 Rackmount adapter, left side 7170.0203
1 Rackmount adapter, right side 7170.0204
2 Handles 7320.0006
8 Screws, 6-32 x 5/16” flathead 5113.1110.6
4 Screws, 8-32 x 1/4” flathead 5114.1108
2 Spacers, rackmount side 7120.0015
Fixed Rackmount Adapters
Refer to Figure 2 while performing the following instructions.
1. Remove the four 6-32 x 1/4” screws on each side securing the cover near the front of the
instrument (eight screws total).
2. Remove the front two rubber feet mounted on the right side. They are attached by adhesive; it
may be necessary to carefully slide a thin blade between them and the panel.
3. Attach the two fixed rackmount adapters (items 1 and 2), using the 6-32 x 5/16” flathead screws
and the 10-32 x 5/16” truss head screws (item 4) from the kit. Note that there is a right and a
left bracket; the correct bracket will align with the front panel when installed.
4. Install the handles (item 6) on the rackmount adapters, using the 8-32 x 1/4” flathead screws
(item 3) from the kit. The handles should be positioned with their offset toward the center of
the instrument.
5. Install the instrument in your rack, using 10-32 screws (not supplied) to match your other
mounting hardware. Because of the weight of the instrument and depending on your rack
configuration, an assistant may be required.
6. Secure the rear of the rackmount adapters to the rack if desired. Because of the variety of rack
configurations, specific hardware and instructions are not supplied.
Figure 2. Fixed rackmounting installation
Slide-out Rackmount Adapters
Refer to Figure 1 while performing the following instructions.
Figure 1. Slide-out racknounting installation
Note: The components of the sliding rackmount assemblies are interchangeable. Two
right-hand assemblies are provided as standard components; one of them is simply
installed inverted on the left-hand side.
1. Remove the two 6-32 x 1/4” screws on each side securing the covers nearest the front panel of the
instrument.
2. Install the two rack ear brackets (items 1 and 2), using the 6-32 x 5/16 screws (item 3) from the kit.
Note that there is a right and a left bracket. The correct bracket will have its cutout section toward
the lower part of the instrument when installed. OBSERVE THE WARNING on the figure above.
3. Install the handles (item 6) on the rack ear brackets, using the 8-32 x 1/4” flathead screw (item 7)
from the kit. Note that the handles should be positioned with their offset toward the center of the
instrument.
4. Attach the sections of the rackmount adapters (item 5) to the instrument as shown in Figure 1,
using the rackmount slide spacers (item 8) and 10-32 x 5/16” truss head screws (item 4) from the
kit.
5. Install the stationary section of the sliding assemblies, along with their intermediate sections, in the
desired position in the rack. The top of their front mounting brackets will be approximately 2-1/4
inches (5.7 cm) below the intended top of the instrument when installed.
6. With the intermediate section fully inserted into the stationary rack sections, adjust the distance
between outside surfaces of the stationary rails to be 17-5/8 inches (44.4 cm).
7. Secure the rear of the rack sections, adjusting the distance between them to be the same as
measured in step 6. Universal mounting brackets are provided to address a wide range of rack
configurations.
8. Fully extend the intermediate sections of the sliding assemblies and confirm that they lock into
position.
9. Install the instrument onto the rack sliders, press in the lock buttons, and slide it into the rack.
10. Secure the rack ear brackets to the rack with four 10-32 screws (not supplied) to match the other
mounting screws in your rack.
WARNING!
These rack ear brackets should be
used only to pull the instrument
out on its sliders. They should not
be used to support the weight of
the instrument in the rack.
NOTE:
The rackmounted sections of the
sliding assemblies are not shown.
Andere Audio Precision Prüfgeräte Handbücher
Audio Precision
Audio Precision Portable One Dual Domain Bedienungsanleitung
Audio Precision
Audio Precision ATS-2 Bedienungsanleitung
Audio Precision
Audio Precision AECM206 Bedienungsanleitung
Audio Precision
Audio Precision ATS-1 Bedienungsanleitung
Audio Precision
Audio Precision 2700 Series Bedienungsanleitung
Audio Precision
Audio Precision ATS-2 Bedienungsanleitung
Audio Precision
Audio Precision Portable One Plus Access Bedienungsanleitung
Beliebte Prüfgeräte Handbücher anderer Marken
SMART
SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung
Agilent Technologies
Agilent Technologies BERT Serial Bedienungsanleitung
Agilent Technologies
Agilent Technologies N3280A Bedienungsanleitung
Vernier
Vernier Go Direct Voltage Bedienungsanleitung
Lifeloc
Lifeloc R.A.D.A.R. Bedienungsanleitung
Fluke
Fluke T5-600 Bedienungs- und Montageanleitung
PCB Piezotronics
PCB Piezotronics 8159-0112A Bedienungsanleitung
BW Technologies
BW Technologies MicroDock II Bedienungsanleitung
Sun Nuclear
Sun Nuclear 1027 Bedienungsanleitung
Biomark
Biomark HPR LITE READER Bedienungsanleitung
Hioki
Hioki 3169-20 Bedienungsanleitung
Ashcroft
Ashcroft ATE-100 Bedienungsanleitung