Audio Technica AT-LPW40WN Bedienungsanleitung

AT-LPW40WN/AT-LPW30TK

User Manual

Belt-Drive Turntable

Introduction

Thank you for purchasing this Audio-Technica product.

Before using the product, read through this user manual to ensure that you will use the product correctly. Please keep this manual for future

reference.

This product can be used only in the countries where the product is sold. Make sure that the operating voltage and the plug of AC adapter of the

product are correct for the country you live in.

Package contents

Make sure that you have all the included items listed below before using this product.

If some items are missing or damaged, contact your local Audio-Technica dealer.

• Turntable body • Turntable mat • Platter

• Drive belt • Counterweight • Headshell (AT-HS4) with VM stereo

cartridge*

• Dust cover

• Dust cover hinges

• AC adapter (Approx. 1.5 m (4.9'))

The AC adapter's plug can be removed.

• Quick start guide

• Caution guide

• 45 RPM adapter • RCA audio cable (Approx. 1.0 m (3.3'))

* AT-LPW40WN: AT-VM95E / AT-LPW30TK: AT-VM95C

After purchase, we suggest that you save all packaging materials for possible future storage, moving, or shipping.

Safety precautions

Important information

Warning:

• To prevent fire or shock hazard, do not expose this apparatus to rain

or moisture.

Caution:

• Do not expose this apparatus to drips or splashes.

• To avoid electric shock, do not open the cabinet.

• Refer servicing to qualified personnel only.

• Do not expose this apparatus to excessive heat such as sunshine, fire

or the like.

• Do not subject this apparatus to strong impact.

• This apparatus should be located close enough to the AC outlet so

that you can easily grasp AC adapter at any time.

• In case of emergency, disconnect the AC adapter quickly.

• Do not place any objects filled with liquids, such as vases, on this

apparatus.

• To prevent fire, do not place any open flame sources (such as lighted

candles) on this apparatus.

• Do not install this apparatus in a confined space such as a bookcase

or similar unit.

• Install this apparatus only in the place where ventilation is good.

• The rating label is put on the bottom of this apparatus.

Notes on use

Turntable body

• Do not place and use the product in locations that are considerably

hot or humid, dirty, or subject to extreme vibrations.

• The product should be positioned on a flat, level surface.

Cartridge

• Attach the protector to protect the stylus when the product is not in

use.

• Do not touch the stylus of the cartridge with your finger.

• Do not allow the cartridge's stylus to bump against the platter or the

edge of the record.

Part names and functions

Overall diagram

9Ground (earth) terminal

Connect the amplifier's ground (earth) terminal to this terminal

using the RCA audio cable's ground conductor.

10 Stereo output terminals

Connect the RCA audio cable. Connect it to either the amplifier's

PHONO input jack or its line input jack. The red terminal is the

right channel and the white terminal is the left channel.

11 Output selector switch

If connecting to an amplifier's PHONO input jack, set this switch to

the PHONO position. If connecting to the AUX jack of an amplifier,

set this switch to the LINE position.

12 Power input jack

Connect the AC adapter.

13 Power switch

Switch ON/OFF.

14 Dust cover hinge holder

1Platter

2Drive belt

Installation is required for operation.

3Motor pulley

4Spindle

5Turntable mat

6Control knob

Use to start and stop, as well as select the platter's speed.

7Tonearm

For details, refer to “Tonearm” on p. 4.

8Feet

Adjust the level of the product.

8 8

911 12 1414 1310

Part names and functions

Tonearm

1Counterweight

Balances the tonearm and adjusts to provide the proper tracking

force.

2Tracking force gauge ring

Use to adjust and set the tracking force.

3Tonearm lift

Moves the tonearm vertically to and from the face of the record.

4Tonearm rest with clamp

Use the clamp to secure the tonearm so that it does not move.

5Anti-skate control dial

While the record is playing, a force acts on the stylus tip to pull it

inward. This force can be counteracted by setting the same values

for anti-skate and the tracking force.

6Tonearm lift control lever

Operates the tonearm lift.

7Tonearm

8Locking ring

Rotate the ring to the left (counterclockwise) to secure the

headshell. To remove the headshell, rotate the ring to the right.

9Headshell and cartridge

The cartridge* is attached to the headshell (AT-HS4).

* AT-LPW40WN: AT-VM95E / AT-LPW30TK: AT-VM95C

Preparation for use

Placing the platter

This product requires some assembly before using it for the first time.

Do not connect the AC adapter until assembly is complete.

1. Set the platter on the spindle.

• To avoid damaging the spindle when seating the platter, align the position

of the spindle and the platter's hole, and then slowly seat the platter.

• Make certain that the platter is fully seated on the spindle.

2. Install the belt to the platter drive ring under the platter making

sure the belt is flat when seated, and then attach the belt to the

motor pulley.

•

Make sure that the belt does not get twisted.

Setting up the turntable

• Position the product on a level surface.

• To avoid the effects of vibrations and acoustic pressure, do not

mount the product next to such items as speakers.

• The product may pick up radio static if placed next to a radio.

Therefore, try to keep the product away from radios.

• If the product is near equipment (cell phone, etc.) that emits strong

radio waves, noise may occur.

Leveling the turntable

1. After positioning the product where you want to use it, adjust the

feet so that the product is level.

• Use a level (sold separately) as needed to ensure that the product is level.

Assembling the tonearm

1. Remove the cable tie used to secure the tonearm at the time of

delivery.

• Use the clamp to temporarily secure the tonearm to the tonearm rest.

2. Insert the headshell into the tonearm.

• Hold the right and left edges of the headshell so that you do not damage

the stylus or cut the cartridge’s wires.

3. With the headshell inserted, turn the locking ring

counterclockwise (to the left).

4. With the tracking force gauge ring facing forward, attach the

counterweight to the back of the tonearm, and slowly turn it

counterclockwise (to the left until it clicks on).

Spindle

Platter

Locking ring

Belt

Motor pulley

Untwisted Twisted

Preparation for use

Tonearm balance and tracking force

In order for the cartridge to reproduce audio correctly from the record’s

grooves, the tonearm’s balance and tracking force must be adjusted

to fit the specifications of the cartridge. If the tonearm’s balance and

tracking force are not properly adjusted, the record or the cartridge’s

stylus may become damaged.

• Do not drag the cartridge’s stylus across the record or turntable mat

when adjusting the tonearm’s balance or tracking force. Doing so

may damage the stylus.

Setting tonearm balance

1. Remove the cartridge’s protector.

2. Unlock the tonearm and lift the tonearm lift control lever.

• The tonearm is tilted because the balance has yet to be adjusted.

3. Place the tonearm over the platter. Hold the headshell and lower

the tonearm lift control lever completely.

• Protect the stylus from touching platter.

4. While still lightly holding the headshell, turn the counterweight to

adjust the tonearm’s balance.

• Adjust the balance so that the tonearm is level when you release the

headshell.

5. Return the tonearm to the tonearm rest.

Setting tracking force

1. While supporting the counterweight so that it does not move,

turn the tracking force gauge ring so that its “0” position lines up

with the centerline on the back of the tonearm.

• The tracking force is not adjusted simply by turning the tracking force

gauge ring.

2. Turn the counterweight and the tracking force gauge ring

together counterclockwise from the 0 position (to the left) until

the centerline value matches the recommended tracking force

value for the cartridge you are using.

• Refer to the cartridge maker’s specifications for the recommended tracking

force value.

• The tracking force value for the cartridge provided with this product is 2.0 g.

Setting the anti-skate adjustment

While the record is playing, a force acts on the stylus tip to pull it

inward. This force can be counteracted by setting the same values for

anti-skate and the tracking force.

1. Adjust the anti-skate control dial to have the same value as the

tracking force value.

• The tracking force value for the cartridge provided with this product is 2.0 g.

0.5

2.5

1.5

TonearmCounterweight

Adjust so that tonearm is level

Centerline

Tracking force

gauge ring

Preparation for use

Installing/removing the dust cover

When attaching the dust cover, insert the hinges of the dust cover

into the two dust cover hinge holders on the back of the body. When

removing the dust cover, slowly pull the dust cover out from the dust

cover hinge holders.

Setting output selector switch

This product has a built-in phono equalizer function. You can use the

product, even if you do not have a phono amplifier or connectable

equipment with a built-in phono amplifier, by connecting an active

speaker, etc.

Use the output selector switch to set the output, as shown below.

Connectable

equipment being

used

Position of

output selector

switch

Where to connect the

RCA audio cable

Device with phono

input

PHONO Phono input jack and

ground (earth) terminal of

connectable equipment

Device without

phono input

LINE AUX or line input jack of

connectable equipment

PC sound card LINE Sound card's line input

jack*

* An audio adapter (sold separately) may be required to connect the

RCA audio cable to the PC sound card's line input jack.

Connecting to connectable equipment (active

speakers, amplifiers, etc.)

Align the settings for the output selector switch and connect the RCA

audio cable to an input jack that is compatible with the connectable

equipment you are using (amplifier, receiver, active speakers, sound

card, etc.).

• The RCA audio cable's red jack is for the right (R) channel, and the

white jack is for the left (L) channel.

* Depending on the equipment you are connecting, a ground (earth)

terminal may exist near the phono input jack. If this is the case,

connect to it using the ground line from the RCA audio cable. This

will help prevent a low humming noise that might otherwise be heard

during playback.

Connecting the AC adapter

1. Connect the AC adapter's cord to the power input jack.

2. Plug the AC adapter into an outlet.

• Make sure that the power switch is in the “OFF” position and the control

knob is in the "STOP" position. If the power switch is in the “ON” position

with the AC adapter connected to the outlet, a standby current is always

running through the product even it is not being used.

• If you play a record immediately after plugging the AC adapter into an

outlet, the sound that is played may be garbled. Wait a short time (about

30 seconds) after plugging the AC adapter into the outlet before playing a

record.

With PHONO input*

Without PHONO input

To outlet

Connectable

equipment

(amplifier, etc.)

Playing a record

Before playing a record

1. Remove the cartridge’s protector.

• If the tonearm is fixed to the tonearm rest, remove the clamp.

2. Place the record on the turntable mat so that the center hole

aligns with the spindle.

• If playing a 45 RPM record, attach the 45 RPM adapter (see the diagram to

the right below).

Playing a record

Lower the volume of the amplifier, speakers, etc., sufficiently.

1. Turn the power switch on.

2. Use the control knob to select the speed.

• Select “33” for a 33-⁄ RPM record, or “45” for a 45 RPM record.

• The platter begins spinning.

3. Raise the tonearm by lifting the tonearm lift control lever to the

UP position.

4. Position the tonearm over the desired location (groove) on the record.

5. Lower the tonearm by moving the tonearm lift control lever to the

DOWN position. The tonearm descends slowly onto the record

and play begins.

• Alternatively, you can skip steps 2 to 4, and use your fingers to lift the

headshell, move the tonearm over the desired location on the record, and

then place the headshell down to begin playing the record.

• Do not subject the product to strong impact during playback.

Pausing the record

1. After lowering the volume of the amplifier, speakers, etc.,

sufficiently, lift the tonearm with the tonearm lift control lever.

Stopping the record

1. Lower the volume of the amplifier, speakers, etc., sufficiently.

2. Lift the tonearm lift control lever, return the tonearm to the

tonearm rest, and fix it with the clamp.

3. Turn the control knob to the "STOP" position.

• The platter slows down and rotation stops.

4. Remove the record after the platter has come to a complete stop.

• If the turntable mat gets dirty, it can easily scratch the record, so remove

the turntable mat periodically and wipe off any dust.

• To prevent the record from becoming scratched or warped, remove it

after use.

• Do not use a platter other than the one provided.

• This product is not intended for DJs. Do not touch the record or the

turntable mat while the record is playing.

45-RPM

adapter

At 33-1/3 RPM At 45 RPM

Record

Turntable mat

Protector

Care

Turntable body

• When the turntable body is dirty or dusty, first disconnect the AC

adapter's cord from the power input jack, and then wipe off the dirt

and dust with a soft, dry cloth.

• Do not use benzenes, thinners, etc.

• When storing the product for a long time, disconnect the AC

adapter's cord from the power input jack and the power cable plug

from the outlet then wrap the equipment in plastic; do not allow it to

become damp.

Stylus tip

• If dirt and grime are stuck to the stylus tip, clean it with a

commercially sold brush.

• We recommend using a stylus cleaner (sold separately) if the stylus

tip is considerably dirty. Clean the stylus tip by moving the brush

from the rear to the front of the stylus tip.

Replacing the stylus

Removing the stylus

• In addition to the deterioration of sound quality, records may also be

damaged as the cartridge’s stylus tip wears down.

• As a rule of thumb, replace the stylus after 300 hours of use.

• Be sure to disconnect the product’s power cable plug from the outlet.

1. Release the headshell from the tonearm.

• Fix the tonearm with the clamp and then remove the headshell gently.

2. After lowering the cartridge's protector, remove the stylus by

pulling in the direction of the arrow.

Installing a new replacement stylus

1. Mount the new replacement stylus to the cartridge.

2. Mount the headshell onto the tonearm.

Pull

Align the position of the inner

protrusion.

Andere Handbücher für AT-LPW40WN

Inhaltsverzeichnis

Andere Audio Technica Drehscheibe Handbücher

Audio Technica

Audio Technica AT-LP60XUSB Bedienungsanleitung

Audio Technica

Audio Technica AT95E Bedienungsanleitung

Audio Technica

Audio Technica AT-LP60XHP Bedienungsanleitung

Audio Technica

Audio Technica AT-LP120XUSB Bedienungsanleitung

Audio Technica

Audio Technica AT-LP7 Bedienungsanleitung

Audio Technica

Audio Technica VM760SLC Bedienungsanleitung

Audio Technica

Audio Technica AT-LPW50BT Bedienungsanleitung

Audio Technica

Audio Technica 60th ANNIVERSARY AT-LP2022 Bedienungsanleitung

Audio Technica

Audio Technica VM750SH Bedienungsanleitung

Audio Technica

Audio Technica AT-LP60BK-BT Programmierhandbuch

Audio Technica

Audio Technica AT-PL120 Betriebsanleitung

Audio Technica

Audio Technica AT-LP60XBT-USB Bedienungsanleitung

Audio Technica

Audio Technica AT-LP7 Bedienungsanleitung

Audio Technica

Audio Technica AT-LP5 Betriebsanleitung

Audio Technica

Audio Technica AT-LP120XBT-USB Bedienungsanleitung

Audio Technica

Audio Technica AT-LP5 Bedienungsanleitung

Audio Technica

Audio Technica AT-LPW40WN Bedienungsanleitung

Audio Technica

Audio Technica AT-SB2022 Bedienungsanleitung

Audio Technica

Audio Technica AT-LP60XBT-BK Bedienungsanleitung

Audio Technica

Audio Technica AT-LP120XBTa-USB Bedienungsanleitung

Audio Technica

Audio Technica AT-LP120XBT-USB Bedienungsanleitung

Audio Technica

Audio Technica AT-LP60 Betriebsanleitung

Audio Technica

Audio Technica AT-LP120BK-USB Bedienungsanleitung

Audio Technica

Audio Technica AT-LP60X-RD Bedienungsanleitung

Beliebte Drehscheibe Handbücher anderer Marken

Gemini

Gemini CDT-05 MKII Bedienungsanleitung

Rotel

Rotel RP-820 Bedienungsanleitung

Shuman

Shuman MC-250BT Bedienungsanleitung

Stanton

Stanton STR8-150 Bedienungsanleitung

Crosley

Crosley McQueen CR7011-GY Bedienungsanleitung

Reloop

Reloop SMP-1 Bedienungsanleitung

auna

auna TT-Classic Plus Bedienungsanleitung

COMO AUDIO

COMO AUDIO Turntable Analog Bedienungsanleitung

Dual

Dual 1009 F Bedienungsanleitung

REED

REED Muse3C Bedienungsanleitung

AXIOMTEK

AXIOMTEK OPS883-H Series Bedienungsanleitung

Pioneer

Pioneer PL-71 Bedienungsanleitung

Vestax

Vestax PDX-a1 Bedienungsanleitung

Denon

Denon DP-400 Bedienungsanleitung

Dual

Dual 504 Bedienungsanleitung

Audio-Techica

Audio-Techica AT-LP60XBT Bedienungsanleitung

Goldring

Goldring G99 Bedienungsanleitung

Acoustic Signature

Acoustic Signature Typhoon NEO Bedienungsanleitung