AudioArts Engineering RD-12 Bedienungsanleitung

RD-12 Digital Audio

Console

TECHNICAL MANUAL

March 1999

R-16 / Dec 1997

RD-12 Digital Audio Console Technical Manual - 1st Edition

AUDIOARTS ENGINEERING

600 Industrial Drive

New Bern, North Carolina 28562

252-638-7000

*a division of Wheatstone Corporation

RD-12 / March 1999

ATTENTION

READ ME!

RD-12 / March 99

Attention!

This console contains static sensitive devices:

Normal precautions against static discharge should be observed when

handling individual modules. In particular, modules being packed for shipping

for return or repair must be packed in special static protection bags before

packaging. Damage caused by static discharge may not be covered under

warranty.

Replacing Modules in a Powered-up Console:

While in an emergency situation it is possible to remove and insert modules

on a powered-up console, Wheatstone does not recommend this procedure.

Whenever possible it is best to power down the console first before removing

or replacing modules.

However, if you find you must proceed with this operation, then be sure to

take the following precaution:

When re-inserting a module, take care to replug it squarely into its

mainframe connector socket, so all edgecard fingers make contact

simultaneously. In other words, the gold-plated bus connector fingers on the

bottom edge of the module's printed circuit board must be inserted squarely

(i.e., perpendicular) to the mating socket on the bottom pan of the console

mainframe. The intent is to prevent a situation where one of the module's

power pins makes significant contact before the others. (Naturally, this

same precaution must be taken when using extenders.)

If the above instructions are followed the procedure should be routine; if they

are not, you could run the risk of damaging the console's logic chips.

Again, to avoid ANY possibility of this damage, whenever possible we

strongly recommend powering down the consolebefore replacing any modules.

READEAD

EADEAD

EAD MM

E!!

May 2000

Console Clock Battery Backup

Attention!

Console Clock Display Card

To activate battery backup of the console’s clock simply pull out the yellow

strip from the clock display card, that is mounted on the inside of console

meterbridge, as shown on the picture below.

Your Audioarts RD-12 audio console is equipped with two

"module extractor tools" which are mounted underneath the

console armrest, to the far right (just above and to the left of

the righthand mainframe headphone jack).

Main module faceplates are held into the console mainframe by two

mounting screws (top and bottom). When removed the screws leave

specially threaded holes that accept the two extractor tools.

To remove a module faceplate from the mainframe:

Remove the front top and bottom mounting screws. Remove the extractor

tools from underneath the armrest, and screw each tool into a module

faceplate mounting hole. Use only four or five turns (do not over-insert; you

may damagethe threaded mainframe hole underneath).Using the extractor

tools as handles, pull the module straight up out of the mainframe.

ModuleRemovalTools

E X T R A C T O R T O O L S

page Contents – 1

RD-12 / March 99

CONTENTS

RD-12 Technical Manual

Table of Contents

Chapter 1 – Installation and Power

CountertopMounting................................................................. 1-2

Clearances.............................................................................................................. 1-2

System Ground .......................................................................... 1-2

Power Supplies .......................................................................... 1-4

Power Supply Cable Pinout.................................................................................... 1-5

The VU/Timer Cable ............................................................................................... 1-6

Energizing ............................................................................................................... 1-6

Audio and Control Wiring.......................................................... 1-7

ConnectionProcedures .......................................................................................... 1-7

Insert Points............................................................................................................ 1-7

UnbalancedConnections ....................................................................................... 1-7

Hand crimp tool wiring instructions......................................................................... 1-8

Chapter 2 - Mono Mic Inputs

Module Overview........................................................................ 2-2

Internal Programming Options ................................................. 2-3

Insert Bypass .......................................................................................................... 2-3

Phantom Power ...................................................................................................... 2-3

Mutes ...................................................................................................................... 2-3

Timer Restart .......................................................................................................... 2-3

Tallies...................................................................................................................... 2-4

Utility Bus Pre-Fader .............................................................................................. 2-4

Talkback.................................................................................................................. 2-4

Superphone Output Assign .................................................................................... 2-5

Hook-ups..................................................................................... 2-5

AUDIO CONNECTIONS......................................................................................... 2-5

CONTROL CONNECTIONS................................................................................... 2-6

Remote ON & OFF ................................................................................................. 2-6

Talkback to Control Room ...................................................................................... 2-6

On Tally................................................................................................................... 2-6

Off Tally................................................................................................................... 2-7

RD-12 / Nov 03

page Contents – 2

RD-12 / March 99

CONTENTS

Chapter 3 - Stereo Line Inputs

Module Overview...........................................................................3-2

Internal Programming Options ....................................................3-3

Mutes ........................................................................................................................ 3-3

Timer Restart ............................................................................................................ 3-3

Cue Dropout.............................................................................................................. 3-3

Local/Ready .............................................................................................................. 3-3

Utility Bus Pre-Fader ................................................................................................ 3-4

Tallies........................................................................................................................ 3-4

Superphone Output Assign ...................................................................................... 3-4

Remote On/OFF — Constant vs. Pulse ................................................................... 3-4

Remote START/STOP - Normal vs. EFS................................................................. 3-5

Hook-ups........................................................................................3-5

ANALOG AUDIO CONNECTIONS........................................................................... 3-5

DIGITAL AUDIO CONNECTIONS............................................................................ 3-6

CONTROL CONNECTIONS..................................................................................... 3-6

Remote ON & OFF ................................................................................................... 3-6

On Tally..................................................................................................................... 3-7

External START & STOP ......................................................................................... 3-7

Ready........................................................................................................................ 3-7

Typical Hook-Up Diagram ........................................................................................ 3-8

Chapter 4 - Output Modules

Module Overview...........................................................................4-2

Internal Programming Options ....................................................4-3

Insert Bypass ............................................................................................................ 4-3

Hook-ups........................................................................................4-3

Master Output Module 1 (PGM)

AMP A, B Connectors — Analog Audio............................................................. 4-3

AMP D Connector — Digital Outputs ................................................................ 4-4

Master Output Module 2 (AUD and UTIL)

AMP A, B Connectors — Analog Audio............................................................. 4-4

AMP D Connector — Digital Outputs ................................................................ 4-4

Chapter 5 - Control Room Module

Module Overview...........................................................................5-2

Internal Programming Options ....................................................5-3

Cue Interrupt............................................................................................................. 5-3

Cue Mute .................................................................................................................. 5-3

Mono Cue ................................................................................................................. 5-3

Hook-ups........................................................................................5-4

AMP A, B Connectors — AUDIO.............................................................................. 5-4

AMP B Connector — CONTROL.............................................................................. 5-4

RD-12 / Jan 00

page Contents – 3

RD-12 / March 99

CONTENTS

On-Air Tally......................................................................................................... 5-4

AMP D Connector — AUDIO.................................................................................... 5-5

Chapter 6 - Studio Control Module

Module Overview...........................................................................6-2

Internal Programming Options ....................................................6-3

External Talkback Mute/Dim..................................................................................... 6-3

Studio Dim ................................................................................................................ 6-3

Hook-ups........................................................................................6-4

AMP A, B Connectors — AUDIO.............................................................................. 6-4

AMP B Connector — CONTROL.............................................................................. 6-4

Tally 2 and Tally 3 ............................................................................................... 6-4

AMP C, D Connectors — AUDIO ............................................................................. 6-5

Chapter 7 - Meter Output Module

Module Overview...........................................................................7-2

Internal Programming Options ....................................................7-2

Hook-ups........................................................................................7-2

Chapter 8 - CPU and DSP Modules

Module Overview...........................................................................8-2

AES Clock Sync........................................................................................................ 8-2

CPU-5 Display .......................................................................................................... 8-2

Chapter 9 - Superphone Input Module; optional

Module Overview...........................................................................9-2

Caller Set-Ups .......................................................................................................... 9-2

Automatic Features................................................................................................... 9-3

Inputs and Outputs ................................................................................................... 9-3

Internal Programming Options - Main PCB ................................9-4

Output Assign Switch Enable ................................................................................... 9-4

Mutes ........................................................................................................................ 9-4

Timer Restart ............................................................................................................ 9-4

Tallies........................................................................................................................ 9-4

Cue Dropout.............................................................................................................. 9-5

Gain Trimpots ........................................................................................................... 9-5

Internal Programming Options - Piggyback PCB ......................9-5

External In................................................................................................................. 9-5

Cue Pre/Post ............................................................................................................ 9-5

Gain Trimpots ........................................................................................................... 9-5

Hook-ups........................................................................................9-6

page Contents – 4

RD-12 / March 99

CONTENTS

AUDIO CONNECTIONS (AMP A, B)........................................................................ 9-6

AUDIO and CONTROL CONNECTIONS (AMP C, D) ............................................. 9-6

Chapter 10 - Line Preselector (Analog); optional

Overview .......................................................................................10-2

Internal Programming Options ...................................................10-2

Hook-ups.......................................................................................10-3

Audio Inputs ............................................................................................................. 10-3

Outputs .................................................................................................................... 10-4

Chapter 11 - Line Preselector (Digital/Analog); optional

Overview .......................................................................................11-2

Internal Programming Options ...................................................11-2

LSR-500 (drawing)........................................................................11-3

Hook-ups – LSD-5 ........................................................................11-3

Control Connections ................................................................................................ 11-3

Power Connections.................................................................................................. 11-4

Hook-ups – LSR-500 ....................................................................11-4

Analog Audio Inputs................................................................................................. 11-4

Digital Audio Inputs.................................................................................................. 11-5

Analog Outputs ........................................................................................................ 11-6

Digital Outputs ......................................................................................................... 11-6

DB Connector Pinout Drawing (LSR-500)..................................11-7

Chapter 12 - Intercom Module; optional

Overview .......................................................................................12-2

Internal Programming Options ...................................................12-2

Cue Enable .............................................................................................................. 12-3

Input Signal .............................................................................................................. 12-3

Power for various ICMs ........................................................................................... 12-3

Station Select........................................................................................................... 12-3

Hook-ups.......................................................................................12-4

AMP B Connector - AUDIO ..................................................................................... 12-4

AMP A, B Connectors - CONTROL......................................................................... 12-4

AMP D Connector - AUDIO ..................................................................................... 12-5

AMP C, D Connectors - CONTROL ........................................................................ 12-5

Chapter 13 - Tape Remote Module; optional

Overview .......................................................................................13-2

Hook-ups.......................................................................................13-3

RD-12 / June 00

page Contents – 5

RD-12 / March 99

CONTENTS

START/STOP Function Control I/O...................................................................... 13-3

Full-Function Control I/O ...................................................................................... 13-5

Chapter 14 - Meterbridge and Clock

Overview ................................................................................... 14-2

Replacement Parts................................................................... 14-2

Clock ......................................................................................... 14-2

Controls................................................................................................................. 14-2

Setting the Time.................................................................................................... 14-3

Battery Backup ..................................................................................................... 14-3

Operational Modes ............................................................................................... 14-3

Chapter 15 - I/O Schematic Drawings

Mono Mic Input Module Schematic (MMD-500).................................................. 15-2

Stereo Line Input Module Schematic (SLD-500)................................................. 15-4

Digital Stereo Line Input Card Schematic (SRC-500) ......................................... 15-5

Analog Stereo Line Input Card Schematic (SLADC-600) ................................... 15-6

Output Module Schematic (OMD-500) ................................................................ 15-7

Control Room Module Schematic (CRD-500) ..................................................... 15-8

Studio Control Module Schematic (SCD-500)................................................... 15-11

Digital Superphone I/O Card Schematic (SPND-500) ....................................... 15-13

Analog Superphone I/O Card Schematic (SPNA-600)....................................... 15-14

Digital/Audio Line Select Rackmount Schematic (LSR-500) ............................ 15-15

Tape Remote Module Schematic (TRD-500)..................................................... 15-17

Intercom Module Schematic (ICMD-500) ........................................................... 15-18

Appendix - Replacement Parts List

Replacement Parts List .............................................................A-2

RD-12 / Aug 00

Inhaltsverzeichnis

Andere AudioArts Engineering DJ-Equipment Handbücher

AudioArts Engineering

AudioArts Engineering W-12 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung