AudioCodes Mediant 9000 SBC Montageanleitung
Hardware Installation Manual
AudioCodes Session Border Controller Series
Mediant 9000 SBC
Mediant 9080 / 9030 / 9000 Rev. B
Version 7.2 and later
Notice Mediant 9000 SBC | Hardware Installation Manual
Notice
Information contained in this document is believed to be accurate and reliable at the time
of printing. However, due to ongoing product improvements and revisions, AudioCodes
cannot guarantee accuracy of printed material after the Date Published nor can it accept
responsibility for errors or omissions. Updates to this document can be downloaded
from https://www.audiocodes.com/library/technical-documents.
This document is subject to change without notice.
Date Published: November-20-2022
WEEE EU Directive
Pursuant to the WEEE EU Directive, electronic and electrical waste must not be disposed of with
unsorted waste. Please contact your local recycling authority for disposal of this product.
Customer Support
Customer technical support and services are provided by AudioCodes or by an authorized
AudioCodes Service Partner. For more information on how to buy technical support for
AudioCodes products and for contact information, please visit our website at
https://www.audiocodes.com/services-support/maintenance-and-support.
Documentation Feedback
AudioCodes continually strives to produce high quality documentation. If you have any
comments (suggestions or errors) regarding this document, please fill out the Documentation
Feedback form on our website at https://online.audiocodes.com/documentation-feedback.
Stay in the Loop with AudioCodes
Notes and Warnings
For safety, environment and regulatory information, refer to the printed document
“Safety, Compliance and Warranty Information” included in the products packaging.
The device is an INDOOR unit and thus, must be installed ONLY indoors. In addition,
Ethernet port interface cabling must be routed only indoors and must not exit the
- ii -
Notice Mediant 9000 SBC | Hardware Installation Manual
building.
Installation of this device must be in a weather protected location of maximum
ambient temperature of 35°C.
This device must be installed only in a restricted access location.
Service of the device must be made only by qualified service personnel.
AC powered units must be connected only to a grounded AC mains power socket.
Circuit Overloading: Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits might
have on over- current protection and supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
Caution Laser: This device contains a Class 1 LED/Laser emitting device, as
defined by 21CFR 1040 and IEC825. Do not stare directly into the beam or into fiber
optic terminations as this can damage your eyesight.
Caution Electrical Shock: Do not attempt to open or disassemble this device. The
device carries high voltage. Contact with internal components may cause electrical
shock and bodily harm.
For all service and maintenance issues, contact AudioCodes technical support (see
Customer Support above).
Reliable Earthing: Reliable earthing of rack- mounted equipment should be
maintained. Particular attention should be given to supply connections other than
direct connections to the branch circuit (e.g., use of power strips.)
Related Documentation
Document Name
SBC-Gateway Release Notes for Latest Release (LR) Versions 7.4
- iii -
Notice Mediant 9000 SBC | Hardware Installation Manual
Document Name
SBC-Gateway Release Notes for Long Term Support (LTS) Versions 7.4
Mediant 9000 Series SBC User's Manual
Document Revision Record
LTRT Description
41655 Initial document release for Version 7.2.
41557 Management names of Ethernet ports added.
41658 AC power cable warning (Japanese).
41661 SFP network cabling.
41662 SFP configurations; Replacing Copper NIC with Fiber Network Card (new
section); Returning to an Arbitrary Snapshot (updated).
41663 Logo updated; note added to Returning to an Arbitrary Snapshot.
41664 Updates for HPE ProLiant DL360 Gen10 Server.
41666 Default IP address.
41667 Mediant 9030 (and Mediant 9080) added.
41668 LED descriptions for 366FLR, 366T, and PE310G4SPI9LA.
41671 Typo (FLR ports).
41672 Note re fiber support removed in Chapter 5, Fiber Network Card Support.
41673 Added for Version 7.2 and later.
41675 Specifications updated; supported fiber configurations updated.
41676 URL fixed in section Replacing Copper NIC with Fiber Network Card.
41677 Spec. for Mediant 9080 Rev. B disk updated (SATA).
41679 Supported SFP network cards updated.
41700 Product configurations added.
- iv -
Content Mediant 9000 SBC | Hardware Installation Manual
Table of Contents
1 Introduction 1
2 Product Configurations 2
3 Specifications 4
4 Physical Description 5
Physical Dimensions 5
Front Panel 5
Front Panel LEDs 6
Rear Panel 7
Rear Panel LEDs 8
5 Deploying the Device 12
Deploying the Rail Kit 12
Connecting to Power and Replacing Power Supply 12
Connecting Display and Keyboard 14
Connecting Device to IP Network for 1-GbE Copper 14
Connecting Device to IP Network with SFP 16
Viewing Network Port Status 17
6 Fiber Network Card Support 19
Supported Configurations 19
Replacing Copper NIC with Fiber Network Card 19
7 Initial Configuration 21
Reconfiguring Default IP Address to Match Customer Network Settings 21
Licensing the Device 23
8 Installation and Upgrade Issues 24
Installing an HA System 24
Upgrading 24
Reinstalling Software SBC from ISO Image 24
9 Rescue Options 28
-v-
CHAPTER1 Introduction Mediant 9000 SBC | Hardware Installation Manual
1 Introduction
This document describes the hardware of AudioCodes' carrier-grade Mediant 9000 SBC series
and basic deployment.
This document describes the Mediant 9000 series that is based on HPE ProLiant
DL360 Gen10.
To identify the type of Mediant 9000 model, run the following CLI command, as
shown in the examples below:
●Mediant 9080 Rev. B:
show system hardware
CPU: Intel(R) Xeon(R) Gold 6226R CPU @ 2.90GHz, total 64
cores, avx supported
Memory: 98304 MB
Chassis: ProLiant DL360 Gen10
●Mediant 9080 Rev. A / Mediant 9000 Rev. B:
show system hardware
CPU: Intel(R) Xeon(R) Gold 6126 CPU @ 2.60GHz, total 48
cores, avx supported
Memory: 98304 MB
Chassis: ProLiant DL360 Gen10
●Mediant 9030:
show system hardware
CPU: Intel(R) Xeon(R) Silver 4110 CPU @ 2.1GHz, total 32
cores, avx supported
Memory: 32768 MB
Chassis: ProLiant DL360 Gen10
-1-
CHAPTER2 Product Configurations Mediant 9000 SBC | Hardware Installation Manual
2 Product Configurations
The following configurations are available for the Mediant 9080 / 9030 Session Border
Controller product.
Table 2-1: AudioCodes Mediant 9080 / 9030 Session Border Controller Product Configurations
Product Configuration Description
Mediant 9030
M9K30/AC Mediant 9030 Session Border Controller (SBC)
M9K30/AC/R HA-pair of Mediant 9030 Session Border Controllers (SBC)
M9K30/DC Mediant 9030 Session Border Controller (SBC), DC power
M9K30/DC/R HA-pair of Mediant 9030 Session Border Controllers (SBC), DC
power
M9K30/AC/4/10GLR Mediant 9030 Session Border Controller (SBC) with 4 fiber
10GbE-LR interfaces
M9K30/AC/4/10GLR/R HA-pair of Mediant 9030 Session Border Controllers (SBC) with
4 fiber 10GbE-LR interfaces
M9K30/AC/4/10GSR Mediant 9030 Session Border Controller (SBC) with 4 fiber
10GbE-SR interfaces
M9K30/AC/4/10GSR/R HA-pair of Mediant 9030 Session Border Controllers (SBC) with
4 fiber 10GbE-SR interfaces
M9K30/DC/4/10GLR Mediant 9030 Session Border Controller (SBC) with 4 fiber
10GbE-LR interfaces, DC power
M9K30/DC/4/10GLR/R HA-pair of Mediant 9030 Session Border Controllers (SBC) with
4 fiber 10GbE-LR interfaces, DC power
M9K30/DC/4/10GSR Mediant 9030 Session Border Controller (SBC) with 4 fiber
10GbE-SR interfaces, DC power
M9K30/DC/4/10GSR/R HA-pair of Mediant 9030 Session Border Controllers (SBC) with
4 fiber 10GbE-SR interfaces, DC power
Mediant 9080
M9K80/AC Mediant 9080 Session Border Controller (SBC)
-2-
CHAPTER2 Product Configurations Mediant 9000 SBC | Hardware Installation Manual
Product Configuration Description
M9K80/AC/R HA-pair of Mediant 9080 Session Border Controllers (SBC)
M9K80/DC Mediant 9080 Session Border Controller (SBC), DC power
M9K80/DC/R HA-pair of Mediant 9080 Session Border Controllers (SBC), DC
power
M9K80/AC/4/10GLR Mediant 9080 Session Border Controller (SBC) with 4 fiber
10GbE-LR interfaces
M9K80/AC/4/10GLR/R HA-pair of Mediant 9080 Session Border Controllers (SBC) with
4 fiber 10GbE-LR interfaces
M9K80/AC/4/10GSR Mediant 9080 Session Border Controller (SBC) with 4 fiber
10GbE-SR interfaces
M9K80/AC/4/10GSR/R HA-pair of Mediant 9080 Session Border Controllers (SBC) with
4 fiber 10GbE-SR interfaces
M9K80/DC/4/10GLR Mediant 9080 Session Border Controller (SBC) with 4 fiber
10GbE-LR interfaces, DC power
M9K80/DC/4/10GLR/R HA-pair of Mediant 9080 Session Border Controllers (SBC) with
4 fiber 10GbE-LR interfaces, DC power
M9K80/DC/4/10GSR Mediant 9080 Session Border Controller (SBC) with 4 fiber
10GbE-SR interfaces, DC power
M9K80/DC/4/10GSR/R HA-pair of Mediant 9080 Session Border Controllers (SBC) with
4 fiber 10GbE-SR interfaces, DC power
-3-
CHAPTER3 Specifications Mediant 9000 SBC | Hardware Installation Manual
3 Specifications
The following table lists the device's specifications.
Table 3-1: Specifications
Product HW
Revision CPU Memory Disk Chassis
Mediant9030 Rev. A 2 x 8
Cores
2.1 GHz
11-MB
Cache
32 GB
DDR4-
2666/PC4-
21300
Mechanical
hard drive
1-TB SATA
■Chassis type:
1RU
■Network
(max. total 12
ports):
✔1-GbE
(copper):
4-12
ports
✔1 GbE
(SFP): 4-8
ports
✔10 GbE
(SFP+): 4-
8 ports
■Installation
interfaces:
VGA monitor
and
keyboard,
remote
access
through iLO
Mediant9000 Rev. B 2 x 12
Cores
2.6 GHz
19.25-
MB
Cache
96 GB
DDR4-
2666/PC4-
21300
Mechanical
hard drive
600-GB SAS
Mediant9080 Rev. A 2 x 12
Cores
2.6 GHz
19.25-
MB
Cache
96 GB
DDR4-
2666/PC4-
21300
Mechanical
hard drive
600-GB SAS
Rev. B 2 x 16
Cores
2.9 GHz
22-MB
Cache
96 GB
DDR4-
2933/PC4-
23400
Mechanical
hard drive
600-GB SAS
or 1-TB
SATA
For installation instructions of the Mediant 9000 (Gen 8) model, refer to LTRT-41674
Mediant 9000 SBC Hardware Installation Manual Ver. 7.2 and later.
-4-
CHAPTER4 Physical Description Mediant 9000 SBC | Hardware Installation Manual
4 Physical Description
This section provides a physical description of the device.
Physical Dimensions
The device's physical dimensions are listed in the following table.
Table 4-1: Physical Dimensions
Item Description
Physical Dimension 4.29 x 43.46 x 70.7 cm (1.69 x 17.11 x 27.83 in)
Weight (approximate) Between 13.04 kg (28.74 lb) and 16.27 kg (35.86 lb)
Environmental Operational: 10 to 35°C (50° to 95°F)
Front Panel
The device features an 8-SFF (Small Form Factor) cage for standard internal storage hard drives.
The device's front panel is shown in the figures below and described in the subsequent table.
Figure 4-1: Front Panel
Table 4-2: Front Panel
Item # Description
1 600-GB SAS drive or 1-TB SATA drive
2 Serial label pull tab
3 Display port
4 DVD-RW and Display port & USB 2.0 port Kit (DVD-RW is currently not
operational). Re-installation of the SBC application can be performed using the
iLO console virtual media.
-5-
Andere Handbücher für Mediant 9000 SBC
2
Dieses Handbuch passt für folgende Modelle
13
Inhaltsverzeichnis
Andere AudioCodes Server Handbücher
Beliebte Server Handbücher anderer Marken
iRobo
iRobo IPC2U Bedienungsanleitung
Nortel
Nortel 1000 Con?guration guide Bedienungsanleitung
Asus
Asus AP7500 Bedienungs- und Wartungshandbuch
Avid Technology
Avid Technology AirSpeed 5000 Bedienungsanleitung
HP
HP Integrity rx2600 Installationsanleitung
Milestone
Milestone Husky IVO 350T Bedienungsanleitung