Audiomedia AMD 808BT Bedienungsanleitung

AMD 808BT

BLUETOOTH CD/MP3 PLAYER

WITH RADIO AM/FM RDS

USB-SD/MMC BUILT IN

USER’S MANUAL

10R-02 1005

GB - 1

MOD

156UP PTY TA AF

2SCN 3RPT 4SHF DN

PANEL

RELEASE

BUTTON

ENCODER

VOLUME

KNOB

TALK

BUTTON

SLOT

BUTTON

EJECT

BUTTON

PTY

BUTTON

POWER

BUTTON

AMS/

MP3

BUTTON

BAND/

LOUDNESS/

MP3

ENTER

BUTTON

PAUSE

BUTTON

SCAN

BUTTON

SHUFFLE

BUTTON

REPEAT

BUTTON

FUNCTION

SELECT

BUTTON

DISPLAY/

ID3 TAG

INFORMATION

BUTTON

789

DIRECTORY

UP/ DOWN

MIC

ENTER

MOD

156UP PTY TA AF

2SCN 3RPT 4SHF DN

PRESET MEMORY BUTTONS

(M1-M6)

DSP

BUTTON

MUTE

BUTTON

TUNING / SEEK /

TRACK / MP3 FILES SEARCH

UP/DOWN BUTTON

MODE

BUTTON

MICROPHONE

789

MIC

ENTER

CLASSIC

POP DSP

LOCAL

LOUD

PTY

MONO

CLASSIC

POP DSP

LOCAL

LOUD

PTY

MONO

USB

INPUT

AUX - IN

INPUT

HANDLING COMPACT DISCS

MOISTURE CONDENSATION

NOTES ON CDs

P. 2

P. 3

P. 4

P. 1

P. 5

P. 6

P. 7

NOTES ON DISCS

There are paste residue.

Ink is sticky (P.5).

Stickers that are beginning

to peel away, leaving a

sticky residue (P.6).

Labels are attached (P.7).

On a rainy day or in a very damp area, moisture may condense on the lenses inside the unit.

Should this occur, the unit will not operate properly. In such a case, remove the disc and wait

for about an hour until the moisture has evaporated.

A dirty or defective disc may cause sound

dropouts while playing. To enjoy optimum

sound, handle the disc as follows.

Handle the disc by its edge. To keep the

disc clean, do not touch the surface (P.1).

If you use the discs explained below, the

sticky residue can cause the CD to stop

spinning and may cause malfunction or

ruin your discs.

Do not use second-hand or rental CDs that

have a sticky residue on the surface (for

example, from peeled-off stickers or from

ink, or glue leaking from under the

stickers).

Do not stick paper or tape on the disc (P.2).

Before playing, clean the discs with an

optional cleaning cloth. Wipe each disc from

the centre out (P.4).

Do not use solvents such as benzine,

thinner,commercially available cleaners, or

antistatic spray intended for analog discs.

Do not expose the discs to direct sunlight or

heat sources such as hot air-ducts, or leave

them in a car parked in direct sunlight where

there can be a considerable rise in

temperature inside the car (P.3).

Do not use rental CDs with old labels that

are beginning to peel off.

Do not use your CDs with labels or

stickers attached.

**************

*******

****

*******

******* *******

*******

Do Not Use Special Shape CDs

Be sure to use round shape CDs only for

this unit and do not use any special shape

CDs. Use of special shape CDs may

cause the unit to malfunction.(P.8).

Be sure to use CDs with disc mark

Only for this unit.

RECORDABLE REWRITABLE

P. 8

CD-Rs and CD-RWs which have not

undergone finalization processing cannot

be played. (For more information on

finalization processing, refer to the manual

for your CD-R/CD-RW writing software or

CD-R/CD-RW recorder.) Additionally,

depending on the recording status, it may

prove impossible to play certain CDs

record on CD-R or CD-RW.

GB - 2

INSTALLATION

Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up

properly and the unit and system work properly.

Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts

can cause malfunctions.

Consult with your nearest dealer if installation requires the drilling of holes or other modifications of

the vehicle.

Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a

sudden stop, like an emergency stop.

If installation angle exceeds 30° from horizontal, the unit might not give its optimum performance.

Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or

from hot air, from heater, or where it would be subject to dust dirt or excessive vibration.

Be sure to remove the front panel before installing the unit.

DIN FRONT/REAR-MOUNT

This unit can be property installed either from “Front” (conventional DIN Front-mount) or “Rear”(DIN

Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer

to the following illustrated installation methods A and B.

DIN FRONT-MOUNT (Method A)

Installation the unit 1. Dashboard

2. Holder

After inserting the half sleeve into the dashboard,

select the appropriate tab according to the

thickness of the dashboard material and bend

Them inwards to secure the holder in place.

3. Screw

30°

1. Dashboard

2. Nut (5mm)

3. Spring washer

4. Screw (5x25mm)

5. Screw

6. Support Strap

Be sure to use the support strap to secure the

back of the unit in place. The strap can be bent by

hand to the desired angle.

7. Plain washer

182

Removing the unit

a. Frame

b. Insert fingers into the groove in the front of frame

and pull out to remove the frame. (When

re-attaching the frame, point the side

with a groove down wards and attach it.)

c. Insert the levers supplied with the unit into the

grooves at both sides of the unit as shown in figure

until they click. Pulling the levers makes it possible

to remove the unit from the dashboard.

Trim Plate Installation:

Push the trim plate against the chassis until it is fitted.

You must do this before you install the front panel, otherwise it can't be attached.

GB - 3

DIN REAR-MOUNT (METHOD B)

Installation using the screw holes on the sides of the unit.

Fastening the unit to the factory radio mounting bracket.

1. Select a position where the screw holes of the

bracket and the screw holes of the main unit

become aligned (are fitted) and tighten the

screws at 2 places on each side.

2. Screw

3. Factory radio mounting bracket.

4. Dashboard or Console

5. Hook (Remove this part)

Note: the mounting box, outer trim ring, and half-

sleeve are not used for method B installation.

2. DETACHABLE CONTROL PANEL (D.C.P.)

Removing The Detachable Control Panel (D.C.P.).

1. Turn the power off

2. Press the D.C.P. release button

3. Remove the D.C.P.

PANEL RELEASE

BUTTON

Attaching the DCP

CAUTION

1. Attach the panel at the right side first, with point B

on the main unit touching point A on the D.C.P. (As

shown on the digram).

2. Then press the left side of D.C.P. onto the main unit

until a “click” sound is heard.

DO NOT insert the D.C.P from the left side. Doing so may damage it.

The D.C.P can easily be damaged by shocks. After removing it, place it in a protective case and

be careful not to drop it or subject it to strong shocks.

When the release button is pressed and the D.C.P is unlocked, the car's vibrations may cause it

to fall. To prevent damage to the D.C.P, always store it in a protective case after detaching it.

The rear connector that connects the main unit and the D.C.P is an extremely important part.

Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc.

Note:

If the D.C.P is dirty, wipe off the dirt with soft, dry

cloth only. And use a cotton swab soaked in

isopropyl alcohol to clean the socket on the back

of the D.C.P.

Socket

These 2 screws are used to prevent damage to the CD

mechanism during transportation Please make sure to

remove the 2 screws before installing the unit into the

vehicle. DO NOT insert a CD into the unit before removing

the 2 screws.

IMPORTANT

GB - 4

GB- 5

ELECTRICAL CONNECTION

a. Make sure your car battery is a 12 volt (6 filler caps) negative ground system (if not, a

converter will be necessary).

b. Before starting wiring connections, disconnect the power supply by removing the fuse from

the fuse box.

c. Connect the power wire to one of the extra terminals of the fuse box.

d. Connect the black ground wire to a metal part of the car. It is important to make good

contact.

e. Make other wiring connections as shown.

f. If your car does not have ISO connector, you can procure it from any car accessory shop.

Press this button to remove the control panel.

Press this button to turn on or off the power.

BASIC OPERATIONS

PANEL RELEASE BUTTON

POWER BUTTON

Notes: INCORRECT WIRING OR OPERATION WILL AVOID THE WARRANTY OF THIS UNIT.

Fuse Replacement:

To replace the fuse, pull out the blown fuse from the

socket. Insert a new one with same rating.

FUSE

(CAR UNIT BACK SIDE)

DISPLAY BUTTON

For RDS models:

Press this button to view other information such as clock , RDS information, band and

frequency ...etc.

FRONT CABINET

RIGHT TRACK

GROUND

AUX IN

LEFT TRACK

A) Tuner mode (Radio)

B) CDP/MP3 (only if a CD or Mp3 disc is inserted)

C) USB (only if a USB drive is inserted)

D) SD/MMC (only if a SD or MMC card is inserted)

E) AUX mode (only if this unit is equipped with this feature)

Whenever a USB or SD/MMC is being inserted, unit will automatically switch to USB or

SD/MMC mode, does not matter the unit is currently in what mode.

When in USB or SD/MMC mode, if the USB or SD/MMC is being removed, unit will

automatically switch to previous mode.

MODE BUTTON

Press this button to select different mode, sequence as follow:

MODE PRIORITY

FRONT AUX INPUT

Connect the external signal to the front 3.5mm earphone jack on front panel, then press Mode

button to select Aux mode. Press Mode Button again to cancel Aux Mode and return to

previous mode.

4 SPEAKER SYSTEM

GB - 6

AUDIO OPERATIONS

ENCODER VOLUME KNOB

Turn this knob to adjust desired volume level.

FUNCTION SELECT BUTTON

Press this button to select desired audio function.

While the selected function is displayed, turn Volume Knob to adjust the level within 5 seconds,

otherwise the unit will return to volume adjustment mode.

MUTE BUTTON

Press this button to mute the sound. Press it again to resume listening.

DSP BUTTON (DIGITAL SOUND PROCESSOR)

Press this button to toggle the following EQ setting:

At DSP OFF mode, EQ will be controlled by Bass/Treble setting.

BAND/LOUDNESS BUTTON

Press the Band/Loudness Button long to switch the loudness on or off. When Loudness is on,

display will show 'Loud On' for a few seconds.

ORDER OF FUNCTION:

VOLUME(VOL) -> BASS(BAS) -> TREBLE(TRE) ->BALANCE(BAL) ->FADER(FAD)

FLAT->CLASSICS->POP M->ROCK M->DSP OFF

AUX INPUT

Connect the external signal to the RCA line in jack located at the rear of the unit , then press

Mode button to select Aux mode. Press Mode Button again to cancel Aux Mode and return to

previous mode.

TUNING / SEEK UP AND TUNING / SEEK DOWN BUTTONS

1.Press these buttons briefly will operate AUTO SEARCH tuning mode, the radio will tune up or

down to the next station and remain on the frequency.

2.Press these buttons more than 2 seconds, operate as MANUAL SEARCH buttons, under this

mode the tuning frequency will advance up or down rapidly when the button is pressed. If the

buttons are not pressed within 3 seconds, they will return to auto search mode.

BAND/LOUDNESS BUTTON

This a dual function button. Press this button short to change between BAND FM1, FM2, FM3

& AM(MW) bands. Press it long to turn on or off Loudness function.

RADIO OPERATIONS

RADIO SIGNAL STRENGTH METER

This is use to indicate the signal strength of current radio station broadcast. When you choose

RADIO mode, it will show on the display.

Best

reception Worst

reception

Note: If press RESET button, the unit still cannot function normally, please use a cotton

swab soaked in isopropyl alcohol to clean the socket on the back of the control panel.

The RESET button is located on the main unit (as shown on the diagram). To press it vertically

with a ballpoint pen or metal object will activate it. The reset button is to be activated for the

following reasons:

Initial installation of the unit when all wiring is completed.

All the function buttons do not operate.

Error symbol on the display.

RESET BUTTON

GB - 7

AUTO MEMORY STORE/PRESET SCAN BUTTON (AMS)

1.PRESET SCAN: Press AMS button briefly enter Preset Scan mode, it will scan all the preset

stations in the memories, you can hear that will stay on each station for about 5 seconds.

2.AUTO MEMORY STORE: Press AMS button long to enter Auto Store mode, this feature will

automatically scan the current band and enter up to 6 strongest stations into the 6 preset

memories. To stop Auto Store & Scan, press the AMS button again.

STATION PRESET BUTTONS (M1-M6)

1.Press these buttons briefly to recall the stored stations in the selected band.

2.Presetting stations manually, Press the BAND button to select the band for the station to be

preset. Use Tuning Up/Down to tune in the stations to be preset. Press the Preset button at

which you want to store the station for at least 2 second. The preset number will appear on

the display accompanied by a beep, this indicate that the station has been stored into

memory.

CD OPERATIONS

CD SLOT

Insert the disc into CD slot. The CD will begin to play.

CD PAUSE BUTTON

Press this button to pause CD play, press again to release pause.

CD SCAN BUTTON

Press this button, the first 10 seconds of each track will be played sequentially until this button is

pressed again, then normal play will resume at the current track.

CD REPEAT BUTTON

Press this button, the current track will be played repeatedly until this button is pressed again.

CD SHUFFLE BUTTON

Press this button to play all tracks on CD in random. Press again to deactivate it.

EJECT BUTTON

Press this button to eject the CD from the unit. The receiver will switches to radio mode

automatically.

TRACK UP AND TRACK DOWN BUTTON

Press the Track Up Button to skip to the next track or previous track. Press the Track Down

button during play will return to the beginning of the current track, press it one more time to

skip to previous skip. Press and hold Track Up/Down Button to fast forward or fast reverse. CD

player starts when you release the button.

GB - 8

PTY BUTTON

Each time when this button is pressed, the PTY mode will toggle in the following order:

The current PTY code is displayed on the LCD, use the 6 preset buttons to select the other PTY

code, the distribution of program type are as follow :

When PTY code is seleced, the radio will search the band for the station that matches the PTY

code.

PTY Music Group->PTY Speech Group->PTY off

Music Group Speech Group

Button Number

1POP , ROCK NEWS, AFFAIRS, INFO

CULTURE, SCIENCE, VAR IED

JAZZ, COUNTRY WEATHER, FINANCE, C HI LD RE N

EASY, LIGHT SPORT, EDUCATE, DRAM A

NATION, OLDIES SOCIAL, RELIGION, PHONE IN

FOLK TRAVEL, LEISURE, DOCUMENT

TA BUTTON

Press this button briefly to turn on or off the TA mode.

A traffic stations will transmit traffic announcement together with the normal broadcasting

periodically, when TA mode is on and traffic announcement is being broadcasted, the radio will

temporary switch to the reception of traffic announcement even the unit is under CD mode or

even the unit is muted.

The status of TA is indicated by two indicators on the LCD, "TA" and "TP", When TA is turned

on, the TA indicator will light up, if the current station carries Traffic Announcement, the TP

indicator will turn on.

When AF follow mode is on, the radio will from time to time measure the signal strength of the

alternative frequencies that come with the RDS data. When an alternative is found stronger than

the current frequency in several measurements, the radio will switch over to that frequency.

When this button is pressed for more than 2 seconds, the unit enters Regional mode and the

Regional mode status will be displayed on the LCD as "REG ON" and "REG OFF" for a few

seconds.

Some broadcasting stations may change their program from normal broadcasting to regional

broadcasting for a certain period. When regional mode is off, the region identification in the PI

code is ignored, the radio may switch to a local variant of the current program. When region

mode is on, the radio will only switch to a program carrying the exact same PI code.

AF BUTTON

Icon Off : AF follow mode off

Icon On : AF follow mode on and RDS reception OK

Icon Flashing : AF follow mode selected, but no RDS data received

Press this button briefly to switch on or off the AF follow mode, the state of the AF follow mode

will be indicated on the LCD by the "AF" icon:

RDS OPERATIONS

Note: When AF switch is on, at this moment use Tuning Up/Down to search station will

only stop at station which has RDS broadcasting.

Note: When TA switch is on, at this moment use Tuning Up/Down to search station will

only stop at station which has TA broadcasting.

CLASSICS, OTHER

GB - 9

RDS OPERATIONS

OVERVIEW OF THE RDS FUNCTION

Radio Data System (RDS) is a broadcasting service that allows FM stations to send additional

digital information along with the regular radio program signal. Your car stereo offers you a

variety of services. Here are just a few:

- PI (Program identification)

It is a code that identified RDS stations; it is unique for each station.

- PS (PROGRAM Service Name)

The name of current station, it is shown on the display.

- AF (Alternative Frequencies List)

The list(s) of Alternative Frequencies give information on the various transmitters broadcasting

the same program in the same or adjacent reception area. If the main frequency should get

worse, the radio will tune automatically to the strongest Alternative frequency.

- TP (Traffic Program)

If the tuned program carries Traffic Announcement, the TP indicator will turn on.

- TA (Traffic Announcement)

When an actual traffic bulletin is on air, the TA indicator will also turn on.

- PTY (Program Type Codes)

This code is used to designate the current program material being broadcast. With this feature,

you can search the programs that match the selected program type, which is chosen from a

specific list of types.

- CT (Clock Time)

This function permits to update the clock of the receiver the nation from which the station is

broadcasting (from PI). It could happen that on the display will be shown the wrong hour; this

happens because in Italy the Clock Time function is not working yet.

Notes

Depending on the country or region, not all of the RDS functions are available in Italy.

RDS may not work properly if the signal strength is weak or if the station you are tuned to is not

transmitting RDS data.

Inhaltsverzeichnis

Andere Audiomedia Autoempfänger Handbücher

Audiomedia

Audiomedia AMR 116 Bedienungsanleitung

Beliebte Autoempfänger Handbücher anderer Marken

Motorola

Motorola VWA63 Bedienungsanleitung

Nextar

Nextar D3201 Bedienungsanleitung

Alpine

Alpine CDE-163BT Bedienungsanleitung

Pioneer

Pioneer DEH-P645R Bedienungsanleitung

Axxera

Axxera XDMA7600 Betriebsanleitung

XM OnyX Bedienungsanleitung

Sound Storm

Sound Storm STM93R Bedienungsanleitung

Soundstream

Soundstream VIR-5000 Bedienungsanleitung

Avson

Avson MKT Platform Bedienungsanleitung

Sony

Sony MEX-1HD - Audio Library System Bedienungsanleitung

Pioneer

Pioneer DVH-P500UB Bedienungsanleitung

JVC

JVC KD-AHD69 Bedienungsanleitung

Blaupunkt

Blaupunkt SANTIAGO CR 87 Bedienungsanleitung

Sony

Sony CDX-4160 - Cd Receiver Bedienungsanleitung

XFIRE AUDIO

XFIRE AUDIO BMW42S Bedienungsanleitung

VDO

VDO CD 2253 Bedienungsanleitung

Volvo

Volvo 13 84 580 Bedienungsanleitung

ZENEC

ZENEC ZE-160DVD Bedienungsanleitung