Audiovox Advent PSD100 Bedienungsanleitung

Front or Rear Parking Sensor System

Model: PSD100 / PSD100C

Installation Manual

TABLE OF CONTENTS

Warnings.......................................................................................4

Product Description......................................................................5

Packing List..................................................................................6

Installation Instructions ................................................................7

Mounting the Sensors .......................................................7

Installing the Power Harness (REAR)..............................9

Installing the Power Harness (FRONT).........................10

Mounting the Speaker.....................................................11

Mounting the Mute/On-Off Button .................................12

Control Module Dip Switch Settings..............................12

Mounting the Control Module........................................13

Setting the Learning System.......................................................14

Specifications..............................................................................15

Maintenance................................................................................15

Troubleshooting..........................................................................15

Warranty.....................................................................................45

Features

•Front or rear install

•Adjustable range to 7ft

•Adjustable sensitivity

•Upgradeable to a 4-sensor system

(requires part #: PSD200/PSD200C)

•Learning capability to ignore vehicle mounted objects

•Auto-mute capability for use with trailer

•Easy install active learning front system

•Includes 0° and 8° sensor sleeves to fit most bumpers

•Will not drain battery or void factory warranty

•Includes adjustable speaker with tricolor LED

•Works with any vehicle

Warnings

This product is intended to assist in safe driving by signaling the driver of

the distance to obstacles in close proximity to the vehicle while the vehicle

is in reverse or moving forward slowly. You, as the driver, are solely

responsible for the safe operation of your vehicle and the safety of your

passengers according to your local traffic regulations. Do not use any

features of this system to the extent it distracts you from safe driving. Your

first priority while driving should always be the safe operation of your

vehicle. Audiovox Electronics Corporation cannot accept any

responsibility whatsoever for accidents resulting from failure to observe

these precautions or safety instructions.

1. This product utilizes high voltage. Any unauthorized modifications

or damage to the product may result in electrical shock. Handle all

components with care. Inspect regularly for damage to

components and cabling.

2. You are responsible for ensuring that the installation of this

product does not void or affect the vehicle manufacturer’s

warranty. Audiovox Electronics Corporation or its subsidiaries are

not liable in full or in part for improper installation resulting in

loss or damage to your property, or for voiding all or part of the

vehicle manufacturer’s warranty.

3. Do not apply excessive force to any of the components contained

within this kit. Excessive force used before, during or after

installation that results in a damaged or non-functional part will

void all warranties.

4. Please follow the procedures in this installation manual. Improper

installation or modification of this product will void all warranties.

Product Description

This Front or Rear Parking Sensor System is designed to assist the driver

by providing an alert when the vehicle is traveling toward a nearby object.

Never rely solely on this product to ensure the area is clear of children

and/or obstructions. This product is not intended to replace existing safety

procedures, but rather to add an additional safety tool for your vehicle.

Packing List

The model PSD100 Front or Rear Parking Sensor System consists of the

following items:

1. Control Module

2. Sensors, 2 each, with 19.68ft length of cable

3. 9-foot power cable

4. Tricolor LED display/speaker with 9ft length of cable

5. Auto-Mute button with 9ft length of cable

6. 2 each of the following sensor sleeves:

a) 0 degree

b) 8 degree

7. Hardware bag includes:

a) 2 tap connectors

b) 6 cable ties

c) Velcro tape 2pcs (1-module, 1-speaker)

d) Alcohol swab pad

e) Lock screw for buzzer/LED (speaker) module

f) Grounding screw/washer/ring terminal

8. Installation Manual

9. User Manual

Installation Instructions

Before installing this product, take time to familiarize yourself with the items

in the box and use the packing list to verify all parts are present.

Mounting the Sensors

Choosing the Correct Sensor Sleeve

Use the application guide below to determine whether a sensor

sleeve will be required. This will affect the diameter of the hole in

the bumper.

Marking and Drilling Holes

Figure 1 (2 sensors) Figure 2 (4 Sensors)

1. Mark the locations of the sensors on the front or rear bumper using a

grease pencil.

a. Identify the sensors height on the bumper and mark. The sensor

height should be between 18” and 30” from the ground.

b. Divide the bumper as shown in Figure 1 for a two sensor install, or as

shown in Figure 2 for a four sensor install.

c. Install the sensors equally from the center of the bumper as shown in

Figure 1 and Figure 2.

d. Inspect behind the bumper where the sensors are to be located to

check for possible obstructions, including metal braces, electrical

wires, and clearance. The sensors need 1.5” of clearance behind the

bumper to be fully inserted and mounted securely. Do not mount

sensors directly above exhaust pipes or with the rear of the sensor

contacting metal. Relocate the sensors if any obstruction exists.

2. Before drilling the holes, use a center punch to make a dimple on the

bumper to prevent the drill from slipping from the intended mark.

3. Drill the sensor holes.

oUse a 26mm Hole Saw if you are using a sensor sleeve.

oUse a 13/16” Hole Saw if you are installing without a sensor sleeve.

oWhen drilling a metal bumper, remove the sharp edges using a round metal

file. Be careful not to enlarge hole when filing.

Installing the Sensor Sleeve and Sensors

NOTE: When installing the sensors into the sensor sleeves, push on the outer

ring of the sensor only. Never push on the center of the sensor.

1. Ensure sensors and sleeves are upright (all products have an alignment mark

on the top).

2. If required, install the sensor into the sleeve.

3. Install the sensor (with sleeve, if required) into the holes drilled in the

bumper.

4. Run the sensor wires through the sensor sleeves in the bumper.

5. Press on the outer ring of the sensor and push until the sensor is flush with the

bumper. The sensor should fit snugly into the bumper and lock into place.

6. Determine where the sensor wires will enter into the trunk area or passenger

compartment. Many vehicles have a factory grommet to allow routing of

wires from the outside to the inside of the vehicle. If needed, drill a hole to

route the wires into the vehicle, taking care when drilling metal. Smooth

edges with a round metal file and use a rubber grommet to protect the wires.

7. Feed the sensor wires through the factory grommet or other opening into the

vehicle for connection to the control module (e.g., into the cab of most trucks

or the trunk of passenger cars).

NOTE: Once the wires are passed through, make sure there is enough wire to

route to the control module. Check that the sensor wires will not be

pinched by moving parts or panels.

8. Cable tie the sensor wires and the power harness wires behind the bumper,

keeping them away from the exhaust system or moving suspension parts

(install power harness before using cable ties). Do not pull on the sensor

wires near the sensor shaft exit point, as this may damage the inner

connections.

Installing the Power Harness (REAR)

1. REAR SENSORS - POWER HARNESS INSTALL.

For installation in the REAR of the vehicle, locate a source of reverse power

(usually at taillight assembly) and accessory power (usually cigarette lighter).

a) REVERSE POWER

Using the tap connector supplied, perform the following steps:

i. Place the un-stripped positive reverse power lead wire on the

run channel.

ii. Insert the un-stripped RED power wire completely.

iii. Make the connection between the wires by crimping down the

metal connector with a pair of pliers, making sure the metal is

flush with the plastic insulator.

iv. Close the top hinged cover until latched.

b) GROUND

The ground wire should be secured directly to the vehicle body or

to a ground wire directly attached to the vehicle body. Using the tap

connector supplied, perform the following steps:

i. Place the un-stripped ground (earth) lead wire on the run

channel.

ii. Insert the un-stripped BLACK power wire completely.

iii. Make the connection between the wires by crimping down the

metal connector with a pair of pliers, making sure the metal is

flush with the plastic insulator.

iv. Close the top hinged cover until latched.

c) ACCESSORY POWER

i. Place the un-stripped accessory lead wire on the

run channel.

ii. Insert the un-stripped ORANGE ground wire completely.

iii. Make the connection between the wires by crimping down the

metal connector with a pair of pliers, making sure the metal is

flush with the plastic insulator.

iv. Close the top hinged cover until latched.

2. Route the power harness wires with the sensor wires to the control box.

Tap/Run Connection

Installing the Power Harness (FRONT)

1. FRONT SENSORS - POWER HARNESS INSTALL.

For installation in the FRONT of the vehicle, locate a source of accessory

power (usually cigarette lighter).

a) ACCESSORY POWER

i. Place the un-stripped accessory lead wire on the

run channel.

ii. Insert the un-stripped RED ground wire completely.

iii. Make the connection between the wires by crimping down the

metal connector with a pair of pliers, making sure the metal is

flush with the plastic insulator.

iv. Close the top hinged cover until latched.

b) GROUND

The ground wire should be secured directly to the vehicle body or to

a ground wire directly attached to the vehicle body. Using the tap

connector supplied, perform the following steps:

i. Place the un-stripped ground (earth) lead wire on the run

channel.

ii. Insert the un-stripped BLACK power wire completely.

iii. Make the connection between the wires by crimping down the

metal connector with a pair of pliers, making sure the metal is

flush with the plastic insulator.

iv. Close the top hinged cover until latched.

2. Route the power harness wires with the sensor wires to the control box.

Tap/Run Connection

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Audiovox Automobilelektronik Handbücher

Audiovox

Audiovox SBAR - SBAR Bar-Type Chrome Back-up Sensor Bedienungsanleitung

Audiovox

Audiovox ASH400 Bedienungsanleitung

Audiovox

Audiovox ACAB104 Bedienungsanleitung

Audiovox

Audiovox Code Alarm PROFESSIONAL SERIES CA 5550SST Bedienungsanleitung

Audiovox

Audiovox CarStream Fehlerbehebungshandbuch

Audiovox

Audiovox CMT-3000 Bedienungsanleitung

Audiovox

Audiovox REMIRS Bedienungsanleitung

Audiovox

Audiovox ACA240 Bedienungsanleitung

Audiovox

Audiovox CNP2000UC - XM Direct 2 Main Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO 9845 Bedienungsanleitung

Audiovox

Audiovox CMOS2 Bedienungsanleitung

Audiovox

Audiovox Auto Security AA-9103N Bedienungsanleitung

Audiovox

Audiovox CMT400 Bedienungsanleitung

Audiovox

Audiovox CMT9300 Bedienungsanleitung

Audiovox

Audiovox CMOS2 Bedienungsanleitung

Audiovox

Audiovox Prestige 128-6182A Bedienungsanleitung

Audiovox

Audiovox Pursuit PT100 Service-Handbuch

Audiovox

Audiovox CMT-500 Bedienungsanleitung

Audiovox

Audiovox PRO 9445FT Bedienungsanleitung

Audiovox

Audiovox Prestige 128-8602 Bedienungsanleitung

Audiovox

Audiovox CMT405 Bedienungsanleitung

Audiovox

Audiovox ACA200 Bedienungsanleitung

Audiovox

Audiovox A-ACC-BMW-DSP Betriebsanleitung

Audiovox

Audiovox Auto Security AS-GMDLT03 Bedienungsanleitung

Beliebte Automobilelektronik Handbücher anderer Marken

GoldCruise

GoldCruise GC90Ci Bedienungsanleitung

DRG

DRG LC 120 Bedienungsanleitung

Blue Ox

Blue Ox BX8848 Bedienungsanleitung

Dometic

Dometic MAGICWATCH MWE890K Bedienungsanleitung

Perfect Power

Perfect Power SMT8-T5 Bedienungsanleitung

Honeywell

Honeywell Thor VM3A Bedienungsanleitung

Waeco

Waeco MagicWatch MWE250 Bedienungsanleitung

Rydeen

Rydeen BKM091 Bedienungsanleitung

Skoda

Skoda 5E0 054 630 Bedienungsanleitung

VDO

VDO SENDER UNIT 2159-0 Bedienungsanleitung

iDataLink

iDataLink maestro Rr Bedienungsanleitung

Movon

Movon MDAS-3LFFHD Bedienungsanleitung

Pioneer

Pioneer Comfort adapter CA-D-PI.150 Bedienungsanleitung

Dietz

Dietz 1110 Bedienungsanleitung

Crux

Crux RVCFD-79 Bedienungsanleitung

Nonda

Nonda ZUS Bedienungsanleitung

iDataLink

iDataLink Maestro Bedienungsanleitung

COBHAM

COBHAM Explorer 325 Bedienungsanleitung