Audiovox CAM300 Bedienungsanleitung

Model: CAM300/CAM310

Full or Partial

Frame Camera

Installation Manual

Features

•Camera Fully Adjustable on all 3 Axis for off centre mounting.

•Frame may be mounted above or below license plate.

•High Resolution, ¼ inch CMOS Color Camera

•Waterproof Housing

•160 Degree Wide View Angle

•Selectable Image: Normal/Reverse

•12v – 24v

Table of Contents

Warnings......................................................................................3

Product Description .....................................................................4

Packing List .................................................................................4

Camera Installation......................................................................5

Camera Wiring Diagram..............................................................8

Specifications ..............................................................................9

Troubleshooting...........................................................................9

Warnings

The product is intended to assist in safe driving and to allow the driver to

have a broader rear view while the vehicle is in reverse. You, as the

driver, are solely responsible for the safe operation of your vehicle and

the safety of your passengers according to local traffic regulations. Do not

use any features of this system to the extent it distracts you from safe

driving. Your first priority while driving should always be the safe

operation of your vehicle. Audiovox Electronics Corporation cannot

accept any responsibility whatsoever for accidents resulting from failure

to observe these precautions or safety instructions.

1. This product utilizes high voltage. Any unauthorized modifications or

damage to the product may result in electrical shock. Handle all

components with care. Inspect regularly for damage to components

and cabling.

2. You are responsible for ensuring that the installation of this product

does not void or affect the vehicle manufacturer’s warranty.

Audiovox Electronics Corporation or its subsidiaries are not liable in

full or in part for improper installation resulting in loss or damage to

your property, or for voiding all or part of the vehicle manufacturer’s

warranty.

3. Do not apply excessive force to any of the components contained

within this kit. Excessive force used before, during or after

installation that results in a damaged or non-functional part will void

all warranties.

4. Please follow the procedures in this installation manual. Improper

installation or modification of this product will void all warranties.

Product Description

This fast and easy to mount back up camera allows you to use the license

frame mounting bolts to securely attach a high quality, fully adjustable

reversing camera. The camera is perfect for use on your car, truck, or van.

This Wired Camera is designed for use with an Advent monitor but is

compatible with most monitors/TFT screens and can be connected using a

standard RCA connector.

Packing List

•CMOS Camera – 1qty

•Mounting Screw – 1 qty

•Power & Adaptor Cables – 1 qty

•Owner’s Manual – 1 qty

Part Numbers

Description Barcode

Quantity

CAM 300B 1

Black Full Frame Camera 30192390 1

Power Cable & Adaptor Cable 30192160 1

Mounting Screw 30192010 1

Manual 30192020 1

CAM 300C 1

Chrome Full Frame Camera 30202390 1

Power Cable & Adaptor Cable 302020160 1

Mounting Screw 30202010 1

Manual 30202020 1

CAM 310B 1

Black Partial Camera 30212390 1

Power Cable & Adaptor Cable 30212160 1

Mounting Screw 30212010 1

Manual 30212020 1

CAM 310C 1

Chrome Partial Camera 30222390 1

Power Cable & Adaptor Cable 30222160 1

Mounting Screw 30222010 1

Manual 30222020 1

Camera Installation

1. Remove the rear license plate.

2. Examine the vehicle to determine the best way to run the power wires

to the reverse lights and the extension cable through the car.

3. The Camera can be mounted above or below the plate. Determine the

mounting location that best suits your needs. Be sure to verify that

your installation plan complies with local laws and requirements.

Some states require that the state name, registration stickers, and

license number are not obstructed in any way.

4. Place the frame camera in front of the license plate and line up the

holes. Fasten the camera mounting bracket and the license plate to the

vehicle using the anti-theft screws provided. After installation of

screws with the tool provided, place the tool in the glove

compartment or other safe place for future use.

NOTE: To adjust the viewing angle, loosen the locking ring on the front

of the camera around the lens and then move the ‘camera ball’ to the

suitable angle and tighten the locking ring back up.

There is an alignment mark on the camera to show the top of the image.

5. Route the camera wiring into the vehicle. The wire can be run through

an existing grommet, behind a tail lamp, under the trunk molding, or

if necessary, through a 5/8 inch hole drilled near the vehicle’s rear

license plate. When choosing a wiring path, make sure the cable

will not be damaged or pinched, as this may cause a short circuit

that is not covered by the warranty. If drilling a hole, perform the

following steps:

a) Acquire a 5/8 inch drill bit, rust preventive, all of which can be

purchased at a hardware store.

b) Check behind the intended drilling location before drilling to

verify that no wires or mechanisms can interfere with or be

damaged during drilling.

c) Check for interference with license plate lights and the hatch

release switch and/or mechanism.

d) Drill a 5/8 inch hole at the selected location.

e) Coat the edge of the hole with rust preventative.

f) Route the camera cable through the grommet and then through

the hole.

g) Insert the grommet in the hole to keep water from entering the

vehicle.

6. Assemble camera and mount on the vehicle.

Wiring the Camera to the Vehicle’s Reverse Lamp

1. Locate the reverse lamp in the tail light assembly.

2. Using the tap connector supplied, perform the following steps:

a) Place the un-stripped positive lead from the tail lamp in the run

channel, which runs completely through the connector.

b) Insert the un-stripped red power wire from the camera

completely into the other channel in the connector.

c) Make the connection between the wires by crimping down the

metal connector with a pair of pliers, making sure the metal is

flush with the plastic insulator.

d) Close the top plastic hinged cover until latched.

3. Attach the black wire to the ground (negative).

4. Repeat the above steps for the red wire.

Connecting the Video Signal

5. If used with an Advent LCD Monitor such as LCD4WM or LCDM42

the camera power and signal will be provided through a single cable

to the monitor (supplied with the monitor).

6. If using an alternative monitor, use the adaptor harness to split the

signal to RCA connections then connect to the female RCA input on

the alternative monitor.

Reverse/Normal Image Adjustment

The camera comes standard with a reversed image, designed for mounting

at the rear of the vehicle. If you need to change to a forward or normal

image view, clip the blue jumper wire loop on the wiring cable (labeled

“Mirror Selection” below) to change the camera image to normal. Secure

the clipped wires with electrical tape. To change back to reverse image

view, reconnect the blue wires and secure with electrical tape.

Camera Wiring

Note: If used with an Advent LCD Monitor such as LCD4WM or

LCDM42 the camera power and signal will be provided through a single

cable to the monitor (supplied with the monitor).

Specifications

1. Voltage: DC9V-DC28V

2. Current: 50 mA

3. Signal System: NTSC

4. Image Sensor: ¼” CMOS Sensor

5. Horizontal Resolution: 480 lines

6. Viewing Angle: 160 degrees

7. Minimum Illumination: 0.7 Lux

8. Image Display: Selectable Normal/Reverse Image

9. Adjustable Viewing Angle

10. Dimensions:

•Camera: 26mm W x 30mm L

Troubleshooting

Symptom Solution

No video signal appears while

reversing the vehicle 1. Check the rear view camera

lens and clean if needed.

2. Check the rear view camera

wiring connection and RCA

connection.

3. Check the Fuse – if blown

replace ONLY with fuse of

equal amperage.

Video image is not sharp enough Clean the camera lens.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Audiovox Digitalkamera Handbücher

Audiovox

Audiovox CCDF Bedienungsanleitung

Beliebte Digitalkamera Handbücher anderer Marken

Mercury

Mercury 350K Bedienungsanleitung

Pentax

Pentax Optio LS 465 Bedienungsanleitung

Sanyo

Sanyo VPC-S1085 Bedienungsanleitung

GE SMART A1255 Bedienungsanleitung

Point Grey

Point Grey Gazelle Bedienungsanleitung

Nikon

Nikon COOLPIX A Bedienungsanleitung

Pentax

Pentax P-5 Bedienungsanleitung

BlazeVideo

BlazeVideo A280 Bedienungsanleitung

Sony

Sony MCA-20 Bedienungsanleitung

Sony

Sony Alpha DSLR-A290 Bedienungsanleitung

ATIK Cameras

ATIK Cameras One Bedienungsanleitung

CohuHD Costar

CohuHD Costar 3930 Series Bedienungsanleitung

Leica

Leica M10-R Bedienungsanleitung

FujiFilm

FujiFilm FinePix A700 Bedienungsanleitung

Lorex

Lorex LNZ81P25 Series Bedienungsanleitung

GE J1470S Bedienungsanleitung

Sony

Sony A6700 Benutzerhandbuch

Canon

Canon EOS ELAN7 Bedienungsanleitung