Audtek VR60S Bedienungsanleitung
User Manual
Audiophile Grade
Stereo Volume Control
Model: VR60S
© Audtek Electronics™ Last Revised: 3/22/2017 audtekelectronics.com
Typical Wiring Diagram
Congratulations on your purchase of the Audtek Electronics™
VR60S Audiophile Grade Volume Control. This product
was manufactured with the highest quality components and
designed to deliver superior performance.
Features:
TheAudtekElectronics™AudiophileGradevolumecontrolsweredesigned
to deliver pristine sound. High-quality non-inductive resistors are used to
taper the power without affecting frequency response. Due to the natural at
impedance, power in is truly power out. Transformer based volume controls
typically roll-off both ends of the audible frequency spectrum and results in a
loss of bass and “air” that effectively changes the timbre of the music.
Use of multiple volumes controls within a home or ofce requires the
use the Audtek Electronics™ MSDB-8 for proper amplier impedance
protection. Up to eight sets of speakers (one set per volume control) can
be used in this fashion without the need for speaker switching devices. The
Audtek Electronics™ MSDB-8 uses non-inductive resistors for impedance
protection to ensure the delity of the input signal.
Eachpackage contains three differentcolor inserts andcoversto match
mostdecors.Toinstall orremovethe insert, gentlyapply pressure tothe rear
tabs of the unit. Removable PCB wiring connectors accept up to 14 gauge
wire and allow you to pre-wire a system during new construction before
the drywall stage, reducing the risk of damage to the unit. The connectors
quickly snap into place when construction is complete.
Specications:
Power Handling: 60 Watts per channel max
Input/Output Wire Up to 14 AWG (compression quick connects)
Specications:
Mounting conguration: Standard single duplex electrical box
Dimensions: 4"H x 1-1/2"W x 3"D (depth in wall 2-3/8")
Installation Instructions:
1. Select Location- Select a convenient location in each room or area
that speakers are desired. You will need one volume control for each
pair of speakers. The most common height is the same level as the
electrical light switches in your home or ofce.
CAUTION: Be certain that there are no electrical wires, water pipes,
heat or cold air return ducts in the planned installation area before you
startcuttingintothewall.Ifthereis anelectrical outletanywhere nearby,
turn off the circuit breaker to avoid possible injury. Use of an electrical
wire nder and/or stud nder (found at most home center stores) may
be of assistance.
2. Mounting Box- The volume control is made to be mounted into a
standard single duplex electrical box (also found at most home center
stores). Mount the box using the instructions provided.
3. Speaker Wire- UseULapproved CMR, CL-2 or CL-3 jacketed speaker
wire when possible. Use minimum 16 gauge wire on runs under
100 feet and 14 gauge on runs over 100 feet. You should run one,
4 conductor wire from the amplier location to each volume control,
this is called “home run” wiring. Next, run a 2 conductor wire from the
volume control to each speaker location.
4. Connector Hookup- Removethegreen speaker PCB connectors from
the back of the unit. Loosen the set screws in the connector.
When hooking up the speaker wires to the connectors be sure to
observe the correct polarity. This is very important because improper
polarity will cause unwanted frequency response aberrations. It is also
important to make sure that the wires from the amplier are connected
to the “Input” and the speaker wires are connected to the “Output”.
Leaveapproximately6-8 inches of wire lengthinsidethe box. For future
reference, mark the wires inside the box with their location using a
permanentmarker.Remove 2"of thejacketfromthespeakerwire.Using
wire strippers remove about 1/4" of insulation from each wire. Twist the
strands of wire tightly before inserting them into the connectors (for the
best possible connection, you may want to tin the wires if you have a
soldering iron available). Insert the speaker wires into the connectors
and tighten the set screws.
5. Attach Connectors- Push the green connectors with wire attached
onto the posts on the PCB.
6. Installing the Control- Install the control in the single duplex gang box
by gently pushing the wires into the box and mounting the control using
the two 1" athead screws supplied. DO NOT OVERTIGHTEN.
7. Reinstall Wall Trim Plate- With the two 1/4" screws removed earlier
reinstall the trim plate.
8. Setting Impedance- Set the volume control to the proper impedance
using the chart listed above.
Andere Audtek Fernbedienung Handbücher
Beliebte Fernbedienung Handbücher anderer Marken
Panasonic
Panasonic EUR7622KB0 Bedienungsanleitung
Bang & Olufsen
Bang & Olufsen Beo4 Bedienungsanleitung
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung
Multiplex
Multiplex PROFI TX 9 Bedienungsanleitung
One Remote
One Remote RMB4 Bedienungsanleitung
FUTABA
FUTABA 9ZAP - PART2 Bedienungsanleitung
