Aumuller M-COM Click Schulungshandbuch

Warranty claims require proper and profes-

sional assembly, installation and maintenance

in accordance with national regulations and

manufacturer‘s instructions of the drives.

The safety instructions in the supplied pro-

duct documentation are to be observed.

Strictly observe the information given in this

and in the instructions for installation of

drives when mounting the M-COM® Click.

Details can be found on our website

www.aumueller-gmbh.de

Keep this instruction over the lifetime of the

product.

M-COM®Click (Main control unit) 24V

• By using the M-COM® Click 6 single actuators (drives

or locks) are linked together in a multi-drive system.

• Whithin seconds, the M-COM® Click congurates the

synchronization as well as the sequence control, if

additional locking drives are involved. When using 2

locking drives, these run parallel.

• The LED display of the M-COM® Click signals the

successful initialization, the number of components

installed in the system and – if occurring – malfunctions.

• The use of standard drives in a drive system saves

storage costs.

• Subsequent installed or exchanged components can be

easily adressed and programmed.

Assembly and Commissioning Instructions

M-COM®Click

Rated voltage: 24V DC +/- 20%, (max. 2 Vss)

Current consumption: <12 mA

Control type: S12

Protection rating: IP30

Ambient temperature range: - 5 °C ... + 70 °C

Dimensions: 40 x 26 x 15 mm

Connection: Aumüller Click

Feature: Congures drive parameters by simply plug-

ging into the free click slot of a multi-drive

system.

Suitable for 24 V- or 230 V-drives, but it can only

be used on the 24 V-side.

Equipment: Tongs for removing the M-COM® Click.

Part.-No.: 524167

Application: Communication module for automatic conguration and

surveillance of max. 4 opening and 2 locking drives

version S12 / S3 in synchronised multi-drive systems.

Assembly Instruction

M-COM®Click

Commissioning / TesT run

InstallatIon step 1: First commissioning

InstallatIon step 2: Test run,

Malfunction, Troublshooting

Switch on the supply voltage - in CLOSE direction.

Observe the LED reaction of the M-COM®Click.

Check each drive separately with regard to the closing

direction and move to the CLOSED end position.

Completely connect the multi-drive system, including

the white wires.

Insert M-COM®Click in the drive.

Switch on the supply voltage - in CLOSE direction.

Observe the LED reaction of the M-COM®Click .

LED blinks red (Factory settings).

LED starts blinking red / green. The communication

- to the multi-drive operation - is running.

LED blinks green, for each participator once. The pro-

cess is complete.

Compare the numer of devices with the numer of

identied participants.

Check the operation of the multi-drive system according

the instructions for installation the drives.

Troublshooting: LED blinks red.

Check wiring and the system.

Eliminate faults.

Reset the M-COM®Click (see chapter „Reset and re-

initialisation of M-COM®Click)“.

Series connection with M-COM®Click

Note the installation position of the M-COM®

Click !

Drive

M-COM®Click

LED

LED display

Display State

lights red

Factory settings

(M-COM®Click is reset).

0,5s - 0,5s

blinks red / green (10 times)

Communication - to the multi-drive

operation - becomes set up.

0,5s - 0,5s - 3s

blinks green (X times)

X drives identied

(1 time blinks = identied one drive).

LED display

Display State

0,5s - 0,5s - 3s

blinks green (per drive 1 time)

System is o.k. (can be operated)

drives identied

(1 time blinks = identied one drive).

0,5s - 0,5s - 3s

blinks red (X-times)

When the number of the

learned drives does not coin-

cide with the number of drives

now recognized.

Fault: System is not o.k.

X drives identied

(1 time blinks = identied one drive).

< <<

Assembly Instruction

M-COM®Click

reseT / DemounTing

Reset and reinitialisation of

M-COM®Click

To reset the system: press the pushbutton within the

drilling for about 5 seconds - using a wire (max.

Ø 1mm). The supply voltage is applied.

The LED starts blinking red and lights after successful

reset permanently red.

The factory setting is reached, the learning process will

automatically restart.

Demounting the M-COM®Click

in case exchanging a faulty drive

In case of exchange a faulty drive, demout and reset the

M-COM®Click.

Switch off the supply voltage.

Disconnect the connection cable from the faulty drive.

Demount the faulty drive.

Remove the M-COM®Click from the drive.

Use the pliers to pull the M-COM®Click out of

the drive.

Mount the new / repaired drive and connect it.

Plug the M-COM®Click in the drive.

Switch on the supply voltage - in CLOSE direction.

Reset the M-COM®Click (see chapter „Reset and re-

initialisation of M-COM®Click)“.

Disposing of faulty equipment according to the instal-

lation instructions of drives.

Note The tongs

is included in the scope of

delivery of M-COM®Click.

Drive

M-COM®Click

wire max. ø1 mm

3 mm immersion depth

LED display

Display State

0,5s - 0,5s

blinks red (6 times)

M-COM®Click is waiting.

continuous

lights red

M-COM®Click is reset

(Factory settings).

9000021701_V0.2_KW 21.2023

TroublshooTing

Troublshooting:

Exchanging a faulty drive in the multi-drive

system:

Troublshooting:

M-COM®Click take off under voltage:

Switch off the supply voltage.

Disconnect the connection cable from the faulty drive.

Demount the faulty drive.

Mount the new / repaired drive and connect it.

Switch on the supply voltage - in CLOSE direction.

Reset the M-COM®Click (see chapter „Reset and re-

initialisation of M-COM®Click)“.

No adjustment is carried out in case of ex-

change of drives with special program-

ming (e.g. stroke, speed)!

In case of repair please order an exchange drive with the

same parameter assignment as that of the faulty drive.

If the M-COM®Click is removed under voltage and the

drives move, then the drives stop immediately.

Insert M-COM®Click again into the drive.

Put the system back into operation.

Dieses Handbuch passt für folgende Modelle

Andere Aumuller Steuereinheit Handbücher

Aumuller

Aumuller EMB 7300 Series Installations- und Betriebshandbuch

Aumuller

Aumuller SHEV EMB 8000+ Series Installations- und Betriebshandbuch

Aumuller

Aumuller SHEV EMB 8000+ Series Installations- und Betriebshandbuch

Aumuller

Aumuller LZ1-2,5A-KNX Installations- und Betriebshandbuch

Aumuller

Aumuller M-COM Schulungshandbuch

Aumuller

Aumuller M-COM Click Schulungshandbuch

Aumuller

Aumuller EMB 7300 Installations- und Betriebshandbuch

Aumuller

Aumuller USKM Schulungshandbuch

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung