Austin Hughes AP-20 Bedienungsanleitung
UM-UV-621-20-Q319V1 www.austin-hughes.com
User Manual
dedicated LCD display solutions
NAP-20
Aluminum front bezel
OP-20
Universal Mounting Open Frame
AP-20
20” LCD
Front NEMA4 / IP65
DP-20
Aluminum front cover
Designed and manufactured by Austin Hughes
UM-UV-621-20-Q319V1 www.austin-hughes.com
Legal Information
First English printing, July 2019
Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness
of the contents. The information in this document is subject to change without notice. We are not liable for any injury or
loss that results from the use of this equipment.
Safety Instructions
Please read all of these instructions carefully before you use the device. Save this manual for
future reference.
■Unplug equipment before cleaning. Don’t use liquid or spray detergent; use a moist cloth.
■Keep equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned environment with
temperatures not exceeding 40º Celsius (104º Fahrenheit).
■When installing, place the equipment on a sturdy, level surface to prevent it from accidentally falling and causing
damage to other equipment or injury to persons nearby.
■When the equipment is in an open position, do not cover, block or in any way obstruct the gap between it and the
power supply. Proper air convection is necessary to keep it from overheating.
■Arrange the equipment’s power cord in such a way that others won’t trip or fall over it.
■If you are using a power cord that didn’t ship with the equipment, ensure that it is rated for the voltage and current
labeled on the equipment’s electrical ratings label. The voltage rating on the cord should be higher than the one listed
on the equipment’s ratings label.
■Observe all precautions and warnings attached to the equipment.
■If you don’t intend on using the equipment for a long time, disconnect it from the power outlet to prevent being
damaged by transient over-voltage.
■Keep all liquids away from the equipment to minimize the risk of accidental spillage. Liquid spilled on to the power
supply or on other hardware may cause damage, fire or electrical shock.
■Only qualified service personnel should open the chassis. Opening it yourself could damage the equipment and
invalidate its warranty.
■If any part of the equipment becomes damaged or stops functioning, have it checked by qualified service personnel.
What the warranty does not cover
■Any product, on which the serial number has been defaced, modified or removed.
■Damage, deterioration or malfunction resulting from:
□Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or
failure to follow instructions supplied with the product.
□Repair or attempted repair by anyone not authorized by us.
□Any damage of the product due to shipment.
□Removal or installation of the product.
□Causes external to the product, such as electric power fluctuation or failure.
□Use of supplies or parts not meeting our specifications.
□Normal wear and tear.
□Any other causes which does not relate to a product defect.
■Removal, installation, and set-up service charges.
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
■Re-position or relocate the receiving antenna.
■Increase the separation between the equipment and receiver.
■Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
UM-UV-621-20-Q319V1 www.austin-hughes.com
Contents
< Part. 1 > AP-20 / NAP-20
1.1 Package Content P.1
1.2 Structure Diagram & Dimension P.2 - 3
1.3 Mounting Hardware & Installation P.4
< Part. 2 > DP-20
2.1 Package Content P.5
2.2 Structure Diagram & Dimension P.6 - 7
2.3 Mounting Hardware & Installation P.8
< Part. 3 > OP-20
3.1 Package Content P.9
3.2 Structure Diagram & Dimension P.10 - 11
3.3 Mounting Hardware & Installation P.12
< Part. 4 > Specifications / OSD
4.1 Product Specifications P.13 - 14
4.2 On-screen Display Operation ( OSD ) P.15
< Part. 5 > Options
5.1 Option Table P.16
5.2 3G / HD / SD-SDI input P.17
5.3 MCS Multi-display control solution P.18
5.4 AV2.2D Upgrade : DVI-D, S-Video + BNC & Audio
AV2.2H Upgrade : HDMI, S-Video + BNC & Audio P.19
5.5 AV3.0 Upgrade : HDMI, DVI-D, S-Video + BNC & Audio P.20
5.6 Resistive ( 1-point touch ) P.21 - 22
5.7 DC Power : 12V / 24V / 48V / 125V P.23
5.8 MIL-type or lockable connector P.24
5.9 TV ( Analog ) P.25 - 26
UM-UV-621-20-Q319V1 www.austin-hughes.com
■It is very important to mount the equipment in a suitable cabinet or on a stable surface.
■Make sure the place has a good ventilation, is out of direct sunlight, away from sources of excessive
dust, dirt, heat, water, moisture and vibration.
The equipment comes with the standard parts shown in package content. Check and make sure they are
included and in good condition. If anything is missing, or damaged, contact the supplier immediately.
Unpacking
Before Installation
How To Clean Your LCD Monitor
Caution :
3
4
■To avoid the risk of electric shock, make sure your hands are dry before unplugging your monitor from or
plugging your monitor into an electrical outlet.
■When you clean your monitor, do not press down on the LCD screen. Pressing down on the screen can
scratch or damage your display. Pressure damage is not covered under warranty.
■Use only cleansers made specifically for cleaning monitors and monitor screens. Cleansers not made to
clean monitors and monitor screens can scratch the LCD display or strip off the finish.
■Do not spray any kind of liquid directly onto the screen or case of your monitor. Spraying liquids directly
onto the screen or case can cause damage which is not covered under warranty.
■Do not use paper towels or abrasive pads to clean your monitor. Using an abrasive pad or any wood
based paper product such as paper towels can scratch your LCD screen.
Cleaning Your Monitor
To clean your LCD safely, please follow these steps :
Disconnect the power cord.
Gently wipe the surface using a clean, dry microfiber cloth. Use as little pressure as possible.
1
2
Cleaning Tough Marks and Smudges
To remove tough marks and smudges, please follow these steps :
Disconnect the power cord.
Spray a small amount of non-abrasive cleanser on a microfiber cloth.
Gently wipe the surface. Use as little pressure as possible.
Wait until your monitor is completely dry before plugging it in and powering it up.
1
2
Caution : Do not spray or apply any liquids directly onto the monitor. Always apply the solution to your
microfiber cloth first, not directly on the parts you are cleaning.
UM-UV-621-20-Q319V1 www.austin-hughes.com
20” LCD Display
P. 1
AV3.0 upgrade I/O with advanced features
- An abundance of input connections that include HDMI, DVI-D, VGA, S-Video + BNC and audio
- On-chip Faroudja® DCDi Cinema processing
- Casing dimensions will be changed
Audio
Power
out - in - in
Video PC
VGA
HDMI
S-VideoBNC
AV2.2H upgrade I/O
Basic I/O
AV2.2D upgrade I/O
Power VGADVI-D
Audio
Power
out - in - in
Video PC
VGADVI-DS-VideoBNC
Audio
Power
out - in - in
Video PC
VGADVI-D
HDMI
S-VideoBNC
20" LCD display X 1
6ft VGA cable X 1
Power adapter X 1
Power cord X 1
AP-20 / NAP-20
Mounting hardware X 1 pack
- Mounting bracket x 4 pcs
- M4* 6mm screw x 8 pcs
- M4* 50mm screw x 8 pcs
< Part 1 > AP-20 / NAP-20
< 1.1 > Package Content
UM-UV-621-20-Q319V1 www.austin-hughes.comP. 2
Rear case
LCD panel
Protective 3mm glass
6mm aluminum front bazel
Audio speaker ( for HDMI, Audio or TV option )
LCD membrane
Remote sensor
1
2
3
4
5
6
7
7
1
2
3
4
6
AP-20
NAP-20
5
Model Product Dimension
(W x D x H) Packing Dimension
(W x D x H) Net
Weight Gross
Weight
AP-20
NAP-20 512.5 x 72.1 x 391.6 mm
20.2 x 2.8 x 15.4 inch
651 x 124 x 597 mm
25.6 x 4.9 x 23.5 inch
7 kg
15.4 lb
9 kg
19.8 lb
< 1.2 > Structure Diagram
Front view
Rear view
Side View
Bottom view
UM-UV-621-20-Q319V1 www.austin-hughes.com
20” LCD Display
P. 3
Front View Side View
Rear View
AP-20
NAP-20
UNIT : mm
1mm = 0.03937 inch
Bottom View
< 1.2 > Dimension
UM-UV-621-20-Q319V1 www.austin-hughes.comP. 4
1
x 4 pcs
Mounting
bracket x 8 pcs
M4*6mm screw
2 3
x 8 pcs
M4*50mm screw
Hardware set part no. UV-BK#2
■Install 4 mounting brackets with 8 x M4*6mm screws
■Adjust the LCD panel with 8 x M4*50mm screws and fix it on the surface.
Steps
M4 screw
■Hardware and M4*4 pcs for VESA mount are not provided
VESA mount ( 100*100mm )
< 1.3 > Installation
( I) Panel mount( I) Panel mount
( II ) VESA mount ( 100*100mm )
UM-UV-621-20-Q319V1 www.austin-hughes.com
20” LCD Display
P. 5
AV3.0 upgrade I/O with advanced features
- An abundance of input connections that include HDMI, DVI-D, VGA, S-Video + BNC and audio
- On-chip Faroudja® DCDi Cinema processing
- Casing dimensions will be changed
Audio
Power
out - in - in
Video PC
VGA
HDMI
S-VideoBNC
AV2.2H upgrade I/O
Basic I/O
AV2.2D upgrade I/O
Power VGADVI-D
Audio
Power
out - in - in
Video PC
VGADVI-DS-VideoBNC
Audio
Power
out - in - in
Video PC
VGADVI-D
HDMI
S-VideoBNC
20" LCD display X 1
6ft VGA cable X 1
Power adapter X 1
Power cord X 1
DP-20
< Part 2 > DP-20
< 2.1 > Package Content
UM-UV-621-20-Q319V1 www.austin-hughes.comP. 6
DP-20
< 2.2 > Structure Diagram
Front view
1
2
3
4
5
Rear case
LCD panel
6mm aluminum front cover
Audio speaker, pair
LCD membrane
1
2
3
5
4
Front view Side View
Rear view
Bottom view
Model Product Dimension
(W x D x H) Packing Dimension
(W x D x H) Net
Weight Gross
Weight
DP-20 481.5 x 67.4 x 360.6 mm
19 x 2.7 x 14.2 inch
651 x 124 x 597 mm
25.6 x 4.9 x 23.5 inch
6.5 kg
14.3 lb
8.5 kg
17 lb
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere Austin Hughes Monitor Handbücher
Austin Hughes
Austin Hughes UltraView AP-19 Bedienungsanleitung
Austin Hughes
Austin Hughes Cyber View RP-W719 Bedienungsanleitung
Austin Hughes
Austin Hughes UltraView AP-F17 Bedienungsanleitung
Austin Hughes
Austin Hughes UltraView X24 Series Bedienungsanleitung
Austin Hughes
Austin Hughes UltraView HDP-17 Bedienungsanleitung
Austin Hughes
Austin Hughes UltraView AP-K55 Bedienungsanleitung
Austin Hughes
Austin Hughes CyberView RP-HW119 Bedienungsanleitung
Austin Hughes
Austin Hughes UltraView OP-K17 Bedienungsanleitung
Austin Hughes
Austin Hughes UltraView AP-8 Bedienungsanleitung
Austin Hughes
Austin Hughes UltraView AP-10 Bedienungsanleitung
Austin Hughes
Austin Hughes UltraView AP-F55 Bedienungsanleitung
Austin Hughes
Austin Hughes AP-K43 Bedienungsanleitung
Austin Hughes
Austin Hughes Cyber View RP-F821TV Bedienungsanleitung
Austin Hughes
Austin Hughes UltraView AP-W19 Bedienungsanleitung
Austin Hughes
Austin Hughes UltraView HAP-K32 Bedienungsanleitung
Austin Hughes
Austin Hughes CyberView XMP Series Bedienungsanleitung
Austin Hughes
Austin Hughes AP-X17 Bedienungsanleitung
Austin Hughes
Austin Hughes Ultra View AP-17 Bedienungsanleitung
Austin Hughes
Austin Hughes AP-K15 Bedienungsanleitung
Austin Hughes
Austin Hughes UltraView AP-K13 Bedienungsanleitung
