Austlift 915210 Bedienungsanleitung
SERVICE MANUAL
WIRE ROPE INERTIA REEL BLOCK
PC. 915210, 915220, 915230
Lifting Your Business to A Higher Level
1300 100 120
www.austlift.com.au
AUSTRALIAN LIFTING CENTRE PTY LTD
2
ALC SIM 915210/915220/915230_19
SERVICE MANUAL (VOL:3)
www.austlift.com.au
WIRE ROPE INERTIA REEL BLOCK
915210/915220/915230
SERVICE MANUAL (VOLUME 3) IS FOR:
Plastic Casing (Wire Rope Retractable Fall Arrester)
Retractable Fall Arrester Block
Product Code. 915210. 915220, 915230
STATUTORY CONDITIONS
1. This Service Manual contains step wise illustrations for the servicing of
AUSTLIFT Retractable Fall Arrest Block.
2. This Service Manual shall be in the custody of only a competent authorized
service personnel, duly endorsed by AUSTLIFT.
3. This Service Manual is meant only to be a handbook for ready reckoning of
the trained service provider for AUSTLIFT Retractable Fall Arrester Block.
4. Once the block has been opened up for servicing by the authorized service
personnel, AUSTLIFT shall not be responsible for any damages/ mishaps
whatsoever. It shall be the duty of the service provider only to respond, to
such a situation.
5. It is extremely important to paste back the original label on to the block
casing after completion of the servicing.
6. Please do not forget to complete the service check card provided along with
the block. This will give easy reference for future use of the block.
3
ALC SIM 915210/915220/915230_19
SERVICE MANUAL (VOL:3)
1300 100 120
WIRE ROPE INERTIA REEL BLOCK
915210/915220/915230
INDEX
4
13
22
Step Wise Illustrations
Changing The Coil Spring
Standard Torque Values
4
ALC SIM 915210/915220/915230_19
SERVICE MANUAL (VOL:3)
www.austlift.com.au
WIRE ROPE INERTIA REEL BLOCK
915210/915220/915230
STEP 1
STEP WISE ILLUSTRATIONS
STEP 2
Follow the below mentioned steps for the
Servicing of Plastic/ Aluminium Casing (Wire Rope
Retractable Fall Arrester) AUSTLIFT Retractable
Fall Arrester Block.
1. Place the Block on the Service table with front side up
2. Ensure that the Allen head of the screw is facing up
3. Now peal off the sticker as shown in the above figure
Remove the Main shaft screw by using 4mm Allen Key and place in a
container as shown in the above Figure.
Main shaft
Screw
5
ALC SIM 915210/915220/915230_19
SERVICE MANUAL (VOL:3)
1300 100 120
WIRE ROPE INERTIA REEL BLOCK
915210/915220/915230
STEP 3
STEP 4
Opening of the Casing
Be sure that the Allen Head of the screw is facing up. Remove the 4
screws , one by one as shown in the figure above.
Now open the casing by just inserting a screw driver in between the two
casing with one hand & carefully holding the webbing assembly by the
other hand to prevent it from abruptly moving out (see figure above).
Casing
Screw
Wire Rope Assembly
Screw
Driver
6
ALC SIM 915210/915220/915230_19
SERVICE MANUAL (VOL:3)
www.austlift.com.au
WIRE ROPE INERTIA REEL BLOCK
915210/915220/915230
STEP 5
STEP 6
Caution: While lifting the Plain casing, the drum will unwind as you lift the
casing. Slide your hand into the drum to prevent the unwinding of the drum.
Now, take out the wire rope along with the Hook & other Plastic parts from
the slot of the Ratchet casing by just pulling it up lightly & then release the
tension of the spring by unwinding the drum in anti clock wise direction as
shown in the above fig. You will need to unwind approximately 4 to 5 turns,
until the drum is completely free of tension. After relieving the tension, turn
the whole assembly upside down.
Drum
Direction of
Unwinding
Pulling out the Wire
Rope assembly
Plain Casing
7
ALC SIM 915210/915220/915230_19
SERVICE MANUAL (VOL:3)
1300 100 120
WIRE ROPE INERTIA REEL BLOCK
915210/915220/915230
STEP 7
STEP 8
Now peel off the sticker on the casing.
Remove the main Shaft screw using 4 mm Allen Key.
Allen
Key
8
ALC SIM 915210/915220/915230_19
SERVICE MANUAL (VOL:3)
www.austlift.com.au
WIRE ROPE INERTIA REEL BLOCK
915210/915220/915230
STEP 9
STEP 10
Remove the Ratchet Casing as shown in the above fig.
Try to pull out the Brass Brakes one by one using your fingers to check that
all Brass Brakes are freely moving in and out & the springs pulling them
inwards are not worn or damaged. If not, replace them. Ensure that there is
no friction, whatsoever between the Brass Brakes & the pivot on which they
rotate. The springs should be intact in their position.
Ratchet Casing
Springs
Brass
Brakes
9
ALC SIM 915210/915220/915230_19
SERVICE MANUAL (VOL:3)
1300 100 120
WIRE ROPE INERTIA REEL BLOCK
915210/915220/915230
STEP 11
STEP 12
We will now plan to replace the wire rope or other wearable parts of the
Retractable, in case they have been damaged or worn out. Open the 3 Nos
Grub Screw with the help of 2.0mm/1.5mm allen key as shown in figure
above.
If Grub screw will found stuck or very tight then follow the below steps
of actions to open them:
1. First we will use L-Type Allen key to loosen the grub screw and T-type Allen
key for further opening.
2. While loosening the screws if any screw is not able to loose (stuck into the
hole) then we will not try to apply excessive force on allen, as it will lead to
deform the drive of grub screw.
3. Fix the assembly in Three jaw chuck and with the help of chuck nut
opening gauge try to move the chuck nut anticlockwise for a bit distance
(stop when cuck nut start moving).
4. Now again use L-Type Allen Key and try to loosen the screw, it will get loose
with a ‘click’ sound. Stop and open the grub screw with T-type Allen key.
Hold the assembly in the Three Jaw Chuck as shown.
Open the Chuck Nut by using the Torque Wrench & the Excel Socket as
shown in above figure.
Torque Wrench
Excel socket
Three Jaw
Chuck
3 nos Grub Screws to be
opened one by one
10
ALC SIM 915210/915220/915230_19
SERVICE MANUAL (VOL:3)
www.austlift.com.au
WIRE ROPE INERTIA REEL BLOCK
915210/915220/915230
STEP 13
STEP 14
Remove the Chuck Nut.
Remove the Pressure Washer. It is essential to replace this Washer Every
time you service a Retractable. So it would be better to discard it and get
a new one in its place.
Pressure Washer
Chuck Nut
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Austlift Hebesystem Handbücher
Beliebte Hebesystem Handbücher anderer Marken
morse
morse 82H-124 Bedienungsanleitung
Braun
Braun NL955 Series Bedienungsanleitung
haacon
haacon 1889.10 Bedienungsanleitung
Protekt
Protekt AT 252 Bedienungsanleitung
R. Beck Maschinenbau
R. Beck Maschinenbau HS 600 Bedienungsanleitung
Nova Technology International, LLC
Nova Technology International, LLC NAS Series Bedienungsanleitung
Genie
Genie Z-60/34 Bedienungsanleitung
Screen Technics
Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung
Mortuary Lift
Mortuary Lift ULTIMATE 1000 Bedienungsanleitung
Custom Equipment
Custom Equipment Hy-Brid 3 Series Programmierhandbuch
Custom Equipment
Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch
Hy-Brid Lifts
Hy-Brid Lifts HB-P3.6 Programmierhandbuch
