Autani CORE Bedienungsanleitung
Document: 80309
Revision-01, November 2021
Autani LLC
7090 Columbia Gateway Drive, Suite 140, Columbia, MD 21046, USA,
(443) 320-2233 | (240) 755-0092 (fax) www.autani.com.
This document contains the Proprietary and Confidential Information of Autani LLC. Any use of this
information without the expressed written consent of Autani, LLC is prohibited. Copyright Autani LLC,
2010-2020. All rights reserved. Please refer to www.autani.com/legal for licensing, intellectual property,
and other legal notices and information.
Quick Installation Sheet
Autani CORE/Manager
Page | 2
1. Mounting Instructions
The Autani CORE/Manager can be mounted to a ceiling tile or wall, and should be mounted
within a range of 1000 feet line of sight to the controlling/communication devices, and near a
120VAC wall outlet. When using fixture controllers with the CORE/ Manager, please consult
with Autani support to determine the distance between edge devices and the CORE/Manager,
as these ranges may vary based on the edge device that is used.
NOTE: The CORE/Manager should NOT be installed near any type of heat sources. Specifically,
heating systems or areas that are receiving direct sunlight for the majority of the day.
1.1. Space Requirement
The CORE/Manager should be mounted with minimum clearances for ventilation and signal
transmission, as shown below.
Page | 3
1.2. Mounting the CORE/Manager onto a Wall
1. Position the wall plate on a wall and mark the four mounting holes. Remove the wall
plate and pre-drill the mounting holes.
2. Insert wall anchors into the mounting holes, and position the wall plate to align with the
mounting holes.
3. Insert the screws through the wall plate into the mounting holes. Tighten the screws.
Page | 4
4. Insert the CORE/Manager into the groove on the wall plate. It will snap into place.
Page | 5
1.3. Mounting the CORE/Manager onto a Ceiling
1. Position the wall plate on a ceiling tile and mark the four mounting holes. Remove wall
plate and pre-drill the mounting holes.
2. Position the wall plate on front of ceiling tile and back plate on back of ceiling tile,
aligning the mounting holes.
3. Insert the screws through the wall plate, ceiling tile, and back plate. Tighten the screws.
Page | 6
4. Insert the CORE/Manager into the groove on the wall plate. It will snap into place.
Page | 7
1.4. Removing the CORE/Manager from Wall Plate
1. To remove the CORE/Manager from the wall plate, press the release tab outward on the
wall plate, and then slide the CORE/Manager up.
Page | 8
2. Hardware Connections
▪The CORE/Manager must be installed and used in accordance with
appropriate electrical codes and regulations.
▪Installation by a qualified electrician is recommended.
1. Remove the front cover from the CORE/Manager to make connections. Press the snap-fit
on both sides of the CORE/Manager to remove the cover.
Page | 9
2.1. Connection to a Power
2. Connect a power source to the CORE/Manager. There are two options: direct power and
POE.
Surge and Battery Protection Recommended.
NOTE: The CORE/Manager will power ON the moment power is supplied. In cases where
this is not desired, it is recommended to do a safe power-down. Press and release
RESET button and wait around 30 seconds until the LED ring goes dark. For more
information on the status of LED ring, refer to section 5.1. LED Ring Status.
DIRECT POWER
Connect the provided AC/DC power adapter or similar device to the 12VDC port. NOTE: It
is recommended to install the CORE/Manager with a UPS (Uninterrupted Power Supply)
near a grounded, 120VAC wall outlet.
POWER OVER ETHERNET (POE)
The CORE/Manager can be powered using a network switch, POE injector, and an Autani
sourced POE splitter. Below are two examples illustrating the connection options with
the POE method.
Page | 10
NOTE: Using the POE method eliminates the need for an AC outlet near the
CORE/Manager and is used in place of the provided AC/DC power adapter.
2.2. Connecting an External Antenna Extension Kit
3. Before initiating the connection, shutdown the core manager by pressing the Reset
button once. Wait 15 sec for the Red spinning to go Dark. Then, start and wait for Green
Spinning.
Shutdown Phase:
The LED ring will spin RED counterclockwise
(takes ~15 seconds).
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Autani Steuereinheit Handbücher
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
