AuthenTrend ATKey.BLE Bedienungsanleitung
1
ATKey.BLE Quick Guide (Windows 10)
2018.01 rev1.1
• Preface
o ATKey.BLE
o Windows 10 RS2 (Creators Update, build 1703) or later version
o ATKey app (download from Windows Store:
https://www.microsoft.com/store/apps/9P7GR8W9SJD3)
o Note 1: One host device (Windows or Mac) can just pair one BLE key, but one BLE key
can work for multiple host devices (Windows and Mac).
o Note 2: to support FIDO U2F, it needs to download extra U2F plug-in for Chrome
browser to enable it
2
• Before install app
o Enable PIN
§ Windows hello needs PIN code of Windows, please setup it from below page:
• Windows Settings = > Accounts
• Accounts => Sign-in Option
• PIN
o SETUP your PIN code following Windows instructions
3
o After installed, find “ATKey for Windows” icon
4
• Start your ATKey.BLE
o Plug micro-USB power cable in to wake up Key first – LED Blue ON
o Then, LED RED ON, power is charging
o You can continue power charging, or remove the micro-USB cable (if LED is flash RED, it means
low power state, please re-charge it)
o Battery full charge – LED will be off
o Low battery (20% or lower) – the KEY won’t work, RED LED is flashing, please do battery charge
by Micro USB cable
5
• Pair ATKey.BLE to your PC and APP
o Click to run app (ATKey for Windows)
• you can turn system Bluetooth on here
• showing the name of the host PC System
• listing “Registered ATKey here”
• Starts from “+” Add and Register AKTeky
o Discover ATKey (base on RSSI) around the host PC
• Showing discovered ATKey
o 1st example, ever registered and also rename the key
o 2nd example, find a new ATKey, showing BLE ID (last 2 digits we noted on label
sticker)
o Click “icon” to connect the specific ATKey …
6
o Wizard mode: 1/6, pair the device
• “Yes” to pair
• Target ATKey LED is flashing (Blue), please tap the fingerprint to confirm the pairing (within 10
sec); if you did not touch the fingerprint to confirm within 10 sec. (timeout), please re-do it by
Cancel first. “Yes” to pair
7
o Next to 2/6, you can type in a name for the key (store inside PC app, not inside the Key)
o Next to 3/6, enroll fingerprint (ATKey BLE LED is flashing by BLUE color)
§ If there is fingerprint enrolled, it will bypass step 3/6, and go to 4/6
§ If there is NO fingerprint enrolled:
8
o Please enroll your fingerprint following screen message (touch and lift, slightly move
finger for more locations of the specific fingerprint to be enrolled, but don’t just
change the angle during your fingerprint enrollment), till 100% showing
§ Please enroll your fingerprint by the same direction; after enrolled, you can
touch by any 360 degrees to verify (but don’t do 360 degree enrollment)
o Just touch the fingerprint by your specific finger
o during the enrollment, the % is increasing like 8%, 16%, …., normally it need 8~10
times enrollment
9
o Next to 4/6, Verify enrolled fingerprint
Verify “Success” ( ATKey LED is Green), then go to 5/6;
Verify “Fail” (LED is RED), then LED continue flashing (Blue), try again; if it continues failed, please
“Cancel” to stop it.
10
o Next to 5/6, register this ATKey to Windows CDF
• “Check” the check box to enable it
o It will request fingerprint verification from ATKey (LED is flashing BLUE)
o And also request “PIN” code verification (Windows behavior)
Inhaltsverzeichnis
Andere AuthenTrend Kartenleser Handbücher
Beliebte Kartenleser Handbücher anderer Marken
Rosslare
Rosslare DR-6255 Bedienungsanleitung
Lindy
Lindy 51541 Bedienungsanleitung
Diapro T?bbi Ürünler
Diapro T?bbi Ürünler Across System Bedienungsanleitung
Johnson Controls
Johnson Controls Kantech tyco ioSmart Bedienungsanleitung
ACS
ACS ACR122L Bedienungsanleitung
Secukey
Secukey S2-MF Bedienungsanleitung
