Autojack ECOCUT-40 Installationshandbuch
SAFETY AND OPERATING MANUAL
ECOCUT-40 Plasma Cutter
ORIGINAL INSTRUCTIONS
2
ECOCUT-40
Welcome to Autojack!
Dear Customer, Congratulations on your purchase.
Before using this product for the first time, please be sure to
read these instructions for use.
They provide you with all the information necessary for using
the product safely and to ensure its long service life.
Closely observe all safety information in these instructions!
General Power Tool Safety Warnings 3
Symbols and Cable Rating Chart 8
Technical Specification/Package Contents 9
Operation 10
Maintenance and Service 11
Autojack Guarantee 13
Declaration of Conformity 15
Machine Schematic 16
Wiring Diagram 17
TABLE OF CONTENTS
3
ECOCUT-40
WARNING, please read all safety
warnings and instructions.
Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for
future reference.
The term “Power tool” in the warnings refers to
your electric (corded) power tool or battery-
operated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignire the dust or
fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
2. Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adaptor plugs with grounded
power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
b} Avoid body contact with grounded surfaces,
such as pipes, radiators, ranges and
refridgerators. There is an increased risk of
electric shock if your body is grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
GENERAL POWER TOOL SAFETY WARNINGS
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk
of electric shock.
3. Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power
tools may result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off position before connecting to
power source and/or battery pack, picking up or
carrying the tool. Carrying power tools with your
finger on the switch or energizing power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
4
ECOCUT-40
e) Do not overreach. Keep proper footing and
balance at all times. This enables better
control of the power tool in unexpected
situations.
f) Dress properly. Do not wear loose clothing
or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce dust-
relatedhazards.
4. Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at
the rate for which it was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from the
power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the
risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
GENERAL POWER TOOL SAFETY WARNINGS
e) Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any other
condition that may affect the power
tool’s operation. If damaged, have the
power tool repaired before use. Many
accidents are caused by poorly
maintained power tools.
f) Use the power tool, accessories
and tool bits etc. in accordance with
these instructions, taking into
account the working conditions and
the work to be performed. Use of the
power tool for operations different
from those intended could result in
a hazardous situation.
5. Service
a) Have your power tool serviced by a
qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power tool
is maintained.
b) If the replacement of the
supply cord is necessary, this has
to be done by the manufacturer
or its agent in order to avoid a
safety hazard.
Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury orfire
5
ECOCUT-40
7
Additional Safety
Instructions for welders
Welders have many sources of danger. It
is therefore particularly important for the
welder to comply with the following rules
so as not to place themselves or others in
danger and to avoid endangering people
and equipment.
a)
Have all work on the mains voltage
system, for example on cables, plugs,
sockets, etc., performed only by trained
electricians. This particularly applies to
configuring intermediate cables.
b)
If an accident occurs, disconnect the
welding power source from the mains
immediately.
c)
If electric touch voltages occur, switch
off the welding set immediately and have
it checked by an expert.
d)
Always check for good electrical
contacts on the welding current side.
e)
Wear insulating gloves on both hands
for welding. These offer protection from
electric shocks (idling voltage in the
welding circuit), harmful radiation (Heat
and UV radiation) and from glowing
metal and slag spatter.
f)
Wear firm, insulated footwear. Your
shoes should also protect you in wet
conditions. Open- toed footwear is not
suitable since falling droplets of glowing
metal will cause burns
GENERAL POWER TOOL SAFETY WARNINGS
e) Wear suitable clothing, do not wear
synthetic clothes.
f) Do not look into the arc with
unprotected eyes, use only a welding
safety shield with the proper safety glass in
compliance with DIN standards. In addition to
light and heat, which may cause dazzling and
burns, the arc also gives off UV radiation.
Without proper protection, this invisible
ultraviolet radiation causes very painful
conjunctivitis, which will only be noticeable
several hours later. In addition, UV radiation
will cause sunburn-type symptoms on
unprotected parts of the body.
g) Personnel or assistants in the vicinity of the
arc must also be notified of the
dangers and provided with the required
protection; if necessary install safety walls.
h) Ensure adequate ventilation for
welding, particularly in small rooms
since the process causes smoke and
harmful gases.
i) Do not carry out any welding work on tanks
that have been used to store gases, fuels,
mineral oil or the like, even if they have been
empty for a lengthy period of time, since any
residue will result in a danger of explosion.
6
ECOCUT-40
l) Special regulations apply in areas where
there is a potential risk of fire and/or
explosion.
m) Welds that are exposed to large stresses
and must comply with safety requirements
may only be completed by specially trained
and approved welders. Examples of such
welds include pressure vessels, rails, trailer
hitches, etc.
n) It must be noted that the protective
conductor in electrical systems of
appliances may be destroyed by the
welding current in the event of negligence,
for example if the earth terminal is placed
on the welding set casing to which the
protective conductor of the electrical
system is connected. The welding work is
completed on a machine with a protective
conductor connection. It is therefore
possible to weld on the machine without
having connected the earth terminal to it.
In this case the welding current will flow
from the earth terminal through the
protective conductor to the machine. The
high welding current may cause the
protective conductor to melt.
o) The fuses on the supply cables to the
mains sockets must comply with the
relevant regulations (VDE 0100). To
comply with these regulations, only fuses
or circuit breakers suitable for the cross-
section of the cables may be used (for
earthing contact sockets max. 16 A fuses or
16 A circuit breakers). The use of too high
a fuse may result in the cable burning and
fire damage to the building.
GENERAL POWER TOOL SAFETY WARNINGS
8. Additional Safety Instructions for
Constricted and Wet Areas
When working in constricted, wet or
hot areas, use insulating supports and
intermediate layers as well as slip-on
gloves made of leather or other non-
conductive materials to insulate your
body against the floor, walls,
conductive parts of the machine and
the like.
If you use small welding transformers
for welding in places with an increase
electrical risk, for example in
constricted areas with conductive
walls, (tanks, pipes, etc.), in wet areas
(which make work clothes wet) and in
hot areas (perspiration on work
clothes), the output voltage of the
welding set when idling must not
exceed 48 V (effective value).
Therefore, the appliance may not be
used for these purposes because its
output voltage is higher than this.
7
ECOCUT-40
9. Additional Safety Instructions for safety
clothing
a) While working, the welder must protect his
entire body from radiation and burns by wearing
suitable clothing and a face guard.
b) Slip-on gloves made of a suitable material
(leather) must be worn on both hands. They must
be in perfect condition.
c) Suitable aprons must be worn to protect
clothing from sparks and burns. A safety suit and if
necessary, head protection must be worn if
required by the type of work in question, e.g.
overhead welding.
d) The safety clothing used as well as all
accessories must comply with the “Personal Safety
Equipment” directive.
10. Additional Safety Instructions for
Protection from Radiation and Burns.
a) Provide information about the risk to eyes at
the working site in the form of a poster with the
wording “Caution – do not look at the flames”.
Workplaces are to be screened off wherever
possible so that personnel in the vicinity are
protected. Unauthorised persons are to be kept
away from the welding work.
b) The walls in the immediate vicinity of
stationary workplaces should not have a light
colour or a sheen. Windows up to head height
are to be protected against radiation passing
through them or reflecting off them, for example
by coating them with a suitable paint.
Do not store or use the equipment in wet
conditions or in the rain. Use the equipment only
indoors.
GENERAL POWER TOOL SAFETY WARNINGS
11. Using an Extension Cable.
a)
If an extension cable is required, use an
approved triple core extension cable
suitable for the power input of the tool.
b)
Grounded tools always require a three
wire extension cable.
c)
As the distance from the supply outlet
increases you must use a heavier gauge
extension cable. Using extension cables with
inadequately sized wire causes a serious drop
in voltage, resulting in loss of power and
possible tool damage.
d)
The smaller the gauge number of the wire
the greater the capacity of the cord.
e)
When using a cable reel, always unwind
the cable completely.
8
ECOCUT-40
SYMBOLS AND POWER RATING CHART
9
ECOCUT-40
SPECIFICATION
ECOCUT-40
Mains Voltage
230v / 50Hz
Rated Max Supply Current
16A
Duty Cycle
25%
No Load Voltage
300V
Current Range
15-40A
Input Current
28.8A
Input Capacity
6.3KVA
Max Cutting Thickness
15mm
Air Pressure
0.15-0.25Mpa
Rated Output Voltage
96v
Protection Class
IP21S
Dimensions
430 x 290 x 390mm
Net Weight
18kg
Gross Weight
19kg
Package Contents
•Plasma Cutter
•Link Lead
•Plasma Torch
•Torch Consumable Set
•Brush
•Mask
•Earth Cable with Clamp
•Instruction Manual
TECHNICAL SPECIFICATION
10
ECOCUT-40
OPERATION
1. Ensure the correct tip is fitted corresponding with the workpiece.
2. Check that the consumables are all in good condition.
3. Make sure your workpiece is clean without rust.
4. Clamp your workpiece using the earth clamp.
5. Set your current dependent on the thickness of the workpiece.
6. Move your torch across the side of the workpiece that you would like to cut
without making contact and whilst pressing the trigger to make the cut.
7. You should hear air hiss out of the torch and an arc will ignite.
8. Once your cut is finished, release the trigger.
9. The arc will cease and the air will hiss out for a couple of seconds when
complete.
The picture shown to the far left
of the image above displays
how you should hold the torch
when cutting. You should be
roughly 2mm away from the
workpiece to ensure minimal
damage to the consumables.
The image above shows how
the electrode and nozzle
should look before and after.
Inhaltsverzeichnis
Andere Autojack Schweißsystem Handbücher
Autojack
Autojack iMIG200DP Installationshandbuch
Autojack
Autojack ECOTIG-160 Installationshandbuch
Autojack
Autojack Mig Master MIG130 Installationshandbuch
Autojack
Autojack EGIMIG-155 Installationshandbuch
Autojack
Autojack Mig Master MIG100 Installationshandbuch
Autojack
Autojack ECN-140 Bedienungsanleitung
Beliebte Schweißsystem Handbücher anderer Marken
TAFA
TAFA 30*8B35 Bedienungsanleitung
Lincoln Electric
Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung
ESAB
ESAB Buddy Arc 145 Bedienungsanleitung
CIGWELD
CIGWELD 636804 Kurzanleitung
Red-D-Arc
Red-D-Arc DC-400 Bedienungsanleitung
Hobart Welding Products
Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung
