Auton 3000-INH Bedienungsanleitung

INVIS-O-TRAK

MODEL

# 3000-INH

# 3000-INV

The Authority in Custom Motorized Lifts

INSTALLATION MANUAL

WWW.AUTON.COM

29102 Hancock Pkwy | Valencia, California 91355

Phone: 661-257-9282 | Fax: 661-295-5638

E-mail: [email protected]

Step 1: Horizontal

A. With mechanism in “open” position, attach

to jamb using all 8 mounting holes (4 upper

and 4 lower).

the face of the wall.

C. Make certain horizontal rails are level, or

picture will not hang level.

Step 3:

A. Attach “hanger rail”

to back side of painting.

Make certain it’s level.

Installation

Installation support:

We take great pride in manufacturing the best lift systems in the world. Our design and production techniques enable simple installation.

In the event that you require assistance, do not hesitate to contact one of our technicians. We will be happy to answer your questions and resolve

any problems you encounter during the installation process. Phone Support: 661-257-9282, ext. 104 • Email Support: [email protected]m

Step 2:

A. Connect the Molex plugs

between the mechanism and

the control box.

B. Plug power cord into the 115

VAC outlet.

Step 1: Vertical

A. With mechanism in “open” position, attach to jamb using all 8 mounting holes

(4 right and 4 left).

C. Make certain vertical rails areperpendicular, or picture will not hang level.

Keep unit free of debris, keep covered prior to installation

1. to increase open travel:

turn the top screw clockwise; turn counter-clockwise to decrease the

down travel.

2. to increase closed travel:

turn the bottom screw clockwise; turn counter-clockwise to decrease the

down travel.

3. Run the lift in the opposite direction for approximately 6” and stop. The motor will recognize the adjustment.

Step 4: Adjust Motor & Limit Switches

(choose which motor you have either a ________ or a __________.

NOTE:

When adjusting the limit switches, turn the adjusting screw in very small increments so

over-adjustment doesn’t occur. Each full turn of the screw corresponds to 3/8” in travel.

caution:

Dropping or jarring unit by hitting walls, ceilings,

or other objects may cause misalignment of lift.

Limit switches are preset at the factory for optimal positioning and performance, but they may be changed.

Two adjusting screws for the limit are located at the end of the motor. The bottom screw controls the open

travel , the top screw controls the closed travel.

*The motor is equipped with a built-in thermal overload protection system. In the event the lift (motor) is moved

too frequently in a short period of time, the unit will be disabled to prevent overheating and possible damage.

The unit will automatically re-set itself within 10-15 minutes.

Using a power tool to adjust the limits will void the warranty.

1. to increase open travel:

turn the bottom screw counter clockwise; turn clockwise to decrease the

up travel.

2. to increase closed travel:

turn the top screw counter clockwise; turn clockwise to decrease the

down travel.

3. Run the lift in the opposite direction for approximately 6” and stop. The motor will recognize the adjustment.

Continued

Adjust Motor and Limit Switch Continued

NOTE:

When adjusting the limit switches, turn the adjusting screw in very small increments so

over-adjustment doesn’t occur. Each full turn of the screw corresponds to 3/8” in travel.

caution:

Dropping or jarring unit by hitting walls, ceilings,

or other objects may cause misalignment of lift.

Limit switches are preset at the factory for optimal positioning and performance, but they may be changed.

Two adjusting screws for the limit are located at the end of the motor. The bottom screw controls the open

travel, the top screw controls the closed travel.

*The motor is equipped with a built-in thermal overload protection system. In the event the lift (motor) is moved

too frequently in a short period of time, the unit will be disabled to prevent overheating and possible damage.

The unit will automatically re-set itself within 10-15 minutes.

Using a power tool to adjust the limits will void the warranty.

1. to increase open travel:

turn the top screw clockwise; turn counter-clockwise to decrease the

down travel.

2. to increase closed travel:

turn the bottom screw clockwise; turn counter-clockwise to decrease the

down travel.

3. Run the lift in the opposite direction for approximately 6” and stop. The motor will recognize the adjustment.

Continued

Adjust Motor and Limit Switch Continued

NOTE:

When adjusting the limit switches, turn the adjusting screw in very small increments so

over-adjustment doesn’t occur. Each full turn of the screw corresponds to 3/8” in travel.

caution:

Dropping or jarring unit by hitting walls, ceilings,

or other objects may cause misalignment of lift.

Limit switches are preset at the factory for optimal positioning and performance, but they may be changed.

Two adjusting screws for the limit are located at the end of the motor. The top screw controls the open

travel , the bottom screw controls the closed travel.

*The motor is equipped with a built-in thermal overload protection system. In the event the lift (motor) is moved

too frequently in a short period of time, the unit will be disabled to prevent overheating and possible damage.

The unit will automatically re-set itself within 10-15 minutes.

Using a power tool to adjust the limits will void the warranty.

- +

Step 5: Operation Instructions

Multi-Function Controller

1) Stop

2) Up*

3) Down*

The multi-function controller operates with RF (Radio Frequency),

IR (Infrared) simultaneously and has3 buttons:

1) Stop - Press and release for stop motion

2) Down/Right – Press and release for down (or Right) motion*

3) Up/Left – Press and release for up (or Left) motion*

Additional Button Functions:

A) When in motion, press the opposite direction.

The lift will pause for 1 second and then reverse direction.

B) When in motion, press the same button direction.

The lift will stop.

* Horizontal Installation moves left and right, Vertical Installation moves up and down

Optional Control Method

Connect optional control accessory

to AUX port

IR Control

Connect the IR eye to the EYE port

Dry Contact Operation:

Short desired operation with COM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Auton Hebesystem Handbücher

Auton

Auton PL-1-9 Bedienungsanleitung

Beliebte Hebesystem Handbücher anderer Marken

morse

morse 82H-124 Bedienungsanleitung

Braun

Braun NL955 Series Bedienungsanleitung

haacon

haacon 1889.10 Bedienungsanleitung

Protekt

Protekt AT 252 Bedienungsanleitung

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Bedienungsanleitung

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Bedienungsanleitung

Genie

Genie Z-60/34 Bedienungsanleitung

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Bedienungsanleitung

Custom Equipment

Custom Equipment Hy-Brid 3 Series Programmierhandbuch

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Programmierhandbuch

BERG

BERG BeNomic EasyLeaf Bedienungsanleitung

Powermate

Powermate LiftGate LG-3 Bedienungsanleitung

Snorkel

Snorkel TM12 Series Bedienungsanleitung

Terberg

Terberg OMNIDEKA Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL625 Betriebsanleitung

Rotary

Rotary SPO16 Bedienungsanleitung