Autonics Krn100 series Bedienungsanleitung

Preface

USER MANUAL

For COMMUNICATION

ii © Copyright Reserved Autonics Co., Ltd.

Preface

Thank you for choosing our Autonics products.

Please familiarize yourself with the information contained in the Safety Considerations section

before using this product.

This user manual for communication contains information about the product and its proper use,

and should be kept in a place where it will be easy to access.

User Manual Guide

iv © Copyright Reserved Autonics Co., Ltd.

User Manual Guide

This user manual for communication contains information about the product and its proper use,

and should be kept in a place where it will be easy to access.

Please familiarize yourself with the information in this manual before using the product.

This manual provides detailed information on the product's features. It does not offer any

guarantee concerning matters beyond the scope of this manual.

This manual may not be edited or reproduced in either part or whole without permission.

A user manual is not provided as part of the product package.

Visit our home-page (www.autonics.com) to download a copy.

The manual's content may vary depending on changes to the product's software and other

unforeseen developments within Autonics, and is subject to change without prior notice.

We contrived to describe this manual more easily and correctly. However, if there are any

corrections or questions, please notify us these on our homepage.

User Manual for Communication Symbols

User Manual for Communication

Symbols

Symbol

Description

Supplementary information for a particular feature.

Failure to follow instructions can result in serious injury or death.

Failure to follow instructions can lead to a minor injury or product damage.

An example of the concerned feature's use.

※1 Annotation mark.

Safety Considerations

vi © Copyright Reserved Autonics Co., Ltd.

Safety Considerations

Please observe all safety considerations for safe and proper product operation to avoid

hazards.

Safety considerations are categorized as follows.

Warning Failure to follow these instructions may result in serious

injury or death.

Caution Failure to follow these instructions may result in personal

injury or product damage.

Fail-safe device must be installed when using the unit with machinery that may cause

serious injury or substantial economic loss. (e.g. nuclear power control, medical equipment,

ships, vehicles, railways, aircraft, combustion apparatus, safety equipment, crime/disaster

prevention devices, etc.)

Failure to follow this instruction may result in personal injury, fire, or economic loss.

The unit must be installed on a device panel before use.

Failure to follow this instruction may result in electric shock.

Do not connect, repair, or inspect the unit while connected to a power source.

Failure to follow this instruction may result in electric shock.

Check the terminal numbers before connecting the power source.

Failure to follow this instruction may result in fire or product damage by a fire.

This unit uses lithium battery. Do not disassemble or burn up this unit.

Failure to follow this instruction may result in explosion.

Do not touch the unit or terminals within 30 sec. after turning off the power.

Failure to follow this instruction may result in electric shock.

Ground the F.G. terminal separately. Grounded wire should be over AWG16(1.25 mm2).

Failure to follow this instruction may result in electric shock.

Do not insert your finger or object into the vent of this unit.

Failure to follow this instruction may result in electric shock or personal injury.

Do not disassemble or modify the unit. Please contact us if necessary.

Failure to follow this instruction may result in fire, personal injury or economic loss.

Do not use the unit outdoors.

Failure to follow this instruction may result in electric shock or shortening the life cycle of the

unit.

When connecting the power input or measuring input, power cable should be over AWG

20(0.50mm2). Make sure to tighten the terminal screw bolt above 0.74 N•m to 0.90 N•m.

Safety Considerations

Use the unit within the rated specifications.

Failure to follow this instruction may result in fire or shortening the life cycle of the unit.

Do not use loads beyond the rated switching capacity of the relay contact.

Failure to follow this instruction may result in insulation failure, contact melt, contact failure,

relay broken, or fire, etc.

When connecting magnet contact as load of relay contact output, connect surge absorber

on coil part of contact.

Failure to follow this instruction may result in malfunction.

Do not use water or oil-based detergent when cleaning the unit. Use dry cloth to clean the

unit.

Failure to follow this instruction may result in electric shock or fire.

Do not use the unit where flammable or explosive gas, humidity, direct sunlight, vibration, or

impact may be present.

Failure to follow this instruction may result in fire or explosion.

Keep dust and wire residue from flowing into the unit.

Failure to follow this instruction may result in fire or malfunction.

Check the polarity of the power contact before wiring the unit.

Failure to follow this instruction may result in fire or explosion.

Check the polarity of the terminal when connecting a temperature sensor to the unit

Failure to follow this instruction may result in cause malfunction.

Check the connection diagram of this manual before supplying power.

Failure to follow this instruction may result in fire.

Do not touch terminal during dielectric or insulation resistance test.

Failure to follow this instruction may result in electric shock.

Use insulation transformer and noise filter power for too much noise from the power. Attach

noise filter on the grounded panel, etc. Use short cables for noise filter output part and

power terminal of the unit.

Failure to follow this instruction may result in product damage, malfunction by surge, etc.

Before connecting temperature sensor (thermocouple, RTD) and analog (voltage, current)

input, set jumper pin of universal input card as input type.

Failure to follow this instruction may result in product damage and malfunction.

Do not connect or separate input, output cards while power is ON.

Failure to follow this instruction may result in serious damage.

Do not open the cover or insert your finger during operation.

Failure to follow this instruction may result in electric shock.

Do not control the alarm output or measure the data during firmware upgrade. Failure to

follow this instruction may result in malfunction. Alarm output, contact input, data

measurement do not operate normally.

After completing firmware upgrade, check the complete message and turn OFF to ON the

power.

Failure to follow this instruction may result in malfunction.

Safety Considerations

viii © Copyright Reserved Autonics Co., Ltd.

All parameter set value is reset after firmware upgrade. It may not operate as same way

with before upgrade operation.

Use voltage output of transmitter power output card only for transmitter power.

Failure to follow this instruction may result in output module damage.

The specifications and dimensions of this manual are subject to change

without notice.

Table of Contents

Preface .............................................................................................................................iii

User Manual Guide ......................................................................................................... iv

User Manual for Communication Symbols....................................................................... v

Safety Considerations ..................................................................................................... vi

Table of Contents ............................................................................................................ ix

1Modbus RTU protocol............................................................................... 11

1.1 Read Coil Status(Func01–01H)......................................................................... 11

1.2 Read Input Status(Func02–02H) .......................................................................12

1.3 Read Holding Registers(Func03–03H) .............................................................13

1.4 Read Input Registers(Func04–04H)..................................................................14

1.5 Preset Single Registers(Func06–06H)..............................................................15

1.6 Preset Multiple Registers(Func16–10H) ...........................................................16

1.7 Exception process (Exception Response-Error Code) .....................................17

2Modbus TCP protocol...............................................................................19

2.1 Read Coil Status(Func01–01H).........................................................................20

2.2 Read Input Status(Func02–02H) .......................................................................21

2.3 Read Holding Registers(Func03–03H) .............................................................22

2.4 Read Input Registers(Func04–04H)..................................................................23

2.5 Preset Single Registers(Func06–06H)..............................................................24

2.6 Preset Multiple Registers(Func16–10H) ...........................................................25

2.7 Exception process (Exception Response-Error Code) .....................................26

3Modbus Mapping Table ............................................................................27

3.1 Read Coil Status(Func 01) / Force Single Coil(Func 05) ..................................27

3.2 Read Discrete Input Status(Func 02)..............................................................28

3.3 Read Input Register(Func 04) ...........................................................................30

3.4 Read Holding Register(Func 03) / Preset Single Register(Func 06) / Preset

Multiple Registers(Func 16) ...........................................................................................34

3.4.1 INPUT SETUP(Input setting)..................................................................... 34

3.4.2 ALARM SETUP(Alarm setting) .................................................................. 59

3.4.3 DIGITAL INPUT SETUP(Digital input setting)............................................ 73

3.4.4 COMMUNICATION SETUP(Communication setting)................................ 77

3.4.5 RECORD SETUP(Record setting .............................................................. 78

3.4.6 SYSTEM SETUP(System setting)............................................................. 80

3.4.7 FILE/MEMORY SETUP(File/Memory setting)............................................ 81

3.4.8 USER INFORMATION SETUP(User information setting).......................... 81

Table of Contents

Andere Handbücher für krn100 series

Inhaltsverzeichnis

Andere Autonics Diktiergerät Handbücher

Autonics

Autonics KRN1000 Series Bedienungsanleitung

Beliebte Diktiergerät Handbücher anderer Marken

Sony

Sony ICD-UX533F Bedienungsanleitung

RCA

RCA VR5230 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics BULLSHOOTER ENDLESS LOOP BS2C Benutzerhandbuch

Sony

Sony TCM-400DV Bedienungsanleitung

LogTag

LogTag TREL30-16 Bedienungsanleitung

SVAT

SVAT CVP800 Bedienungsanleitung

Marantz

Marantz PMD620 Bedienungsanleitung

Zoom

Zoom H4next Bedienungsanleitung

Roland

Roland BR-900CD Bedienungsanleitung

JVC

JVC ProHD GY-HMZ1U Bedienungs- und Wartungshandbuch

Panasonic

Panasonic PQT8531-P Bedienungsanleitung

Sanyo

Sanyo TRC-6400 Bedienungsanleitung

Tascam

Tascam DR-07 Bedienungsanleitung

Olympus

Olympus DW-90 Bedienungsanleitung

Sanyo

Sanyo ICR-B150 Bedienungsanleitung

Korg

Korg D4 Bedienungsanleitung

Sony

Sony ICD-SX46 - Ic Recorder Bedienungsanleitung

Olympus

Olympus DIGITAL VOICE RECORDER WS-200S Montageanleitung

Autonics krn100 series Bedienungsanleitung

Beliebte Diktiergerät Handbücher anderer Marken